Creating logical partitions
The Create Logical Partition wizard on the Hardware Management Console (HMC) guides you through the procedure of creating logical partitions and partition profiles on your server.
The HMC Classic interface is not supported in Hardware Management Console (HMC) Version 8.7.0, or later. The functions that were previously available in the HMC Classic interface are now available in the HMC Enhanced+ interface.
You can create an AIX®, Linux, or IBM® i logical partition by clicking Create Partition, or by using the Create a Partition from Template wizard. For more information about creating a logical partition by using the Create a Partition from Template wizard, see Creating a logical partition by using a template
To create an AIX, Linux, or IBM i logical partition by using Create Partition, complete the following steps:
- In the navigation pane, click the Resources icon .
- Click All Systems. The All Systems page is displayed.
- In the work pane, select the system and click Actions > View System Partitions. The Partitions page is displayed.
- Click Actions > Partitions.
- Click Create Partition. You can create a logical partition with minimum resources. By default, the logical
partition is created in the shared mode with 0.1 processing units for the
Maximum, Allocated, and Minimum
fields and 1 virtual processor for the Maximum,
Allocated, and Minimum fields. When the server does
not support shared processor pools, the logical partition is created in the dedicated mode with 1
processor for the Maximum, Allocated, and
Minimum fields. The default value for the Maximum
field is 4 GB, and 1 GB for the Allocated, and Minimum
fields, for both the shared and dedicated modes. Before you activate the logical partition, you
must assign storage and network resources to the logical partition. Optionally, you can change the
default values that were assigned by using the Manage Partition functions.
Alternatively, you can select the Assign All System Resources check box to assign all the resources to the partition. The logical partition creation succeeds only when all the other active logical partitions and Virtual I/O Servers are shut down.
You can also click the Create Using Templates tab to create a logical partition by using the Create a Partition from Template wizard.
- Creating logical partitions on a new or nonpartitioned server
Use these procedures to create logical partitions on your new or nonpartitioned server using the Hardware Management Console (HMC). - Creating additional logical partitions
You can use the Create Logical Partition wizard on the Hardware Management Console (HMC) to create a new logical partition. When you create a logical partition, you also create a partition profile that contains the resource allocations and settings for the logical partition. - Creating a logical partition with suspension capability
You can create an AIX or Linux logical partition with suspension capability by using the Hardware Management Console (HMC). The HMC provides options to enable suspension of the logical partition when the logical partition is created. The HMC also provides an option to enable suspending a running logical partition. - Enabling the suspension capability of a logical partition
You can enable the suspension capability of a logical partition by using the Hardware Management Console (HMC), after the logical partition is created. - Suspending a logical partition
You can suspend a logical partition by using the Hardware Management Console (HMC) after the logical partition is created. - Recovering a suspended logical partition
When the suspend or resume operation has failed, the logical partition might be in an invalid state. You can then recover a suspended logical partition by using the Hardware Management Console (HMC). - Assigning a single root I/O virtualization logical port to a logical partition
You can assign a single root I/O virtualization (SR-IOV) logical port to a logical partition by using the Hardware Management Console (HMC). - Creating a logical partition with synchronization of the current configuration
You can create an AIX or Linux logical partition with synchronization of the current configuration capability by using the Hardware Management Console (HMC). - Enabling the synchronization of the current configuration capability
You can enable the synchronization of the current configuration capability on a logical partition by using the Hardware Management Console (HMC), after the logical partition is created. - Assigning a reserved storage device to a logical partition
You must assign a reserved storage device to a remote restart capable partition before you activate the logical partition. - Creating a logical partition with the simplified remote restart or remote restart capability
You can create an AIX, IBM i, or Linux logical partition with the partition remote restart capability or the simplified version of the remote restart capability by using the Hardware Management Console (HMC). The HMC provides options to enable the remote restart of the logical partition when the logical partition is created. - Remote restart states
A remote restartable partition goes through several state changes regarding the remote restart operation, both on the source and destination servers. Most of the remote restart operations are supported only when the partition is in the appropriate remote restart state. A remote restart state is not related to the partition state, but is an indicator that is specifically associated with the remote restart operation. - Enabling or disabling the remote restart capability or the simplified version of the remote restart capability
You can enable or disable the remote restart capability or the simplified version of the remote restart capability of a logical partition after the logical partition is created, by using the Hardware Management Console (HMC). - Validating the remote restart operation of a logical partition
You can validate the remote restart operation of an AIX, Linux, or IBM i logical partition by using the Hardware Management Console (HMC) command-line interface. - Remotely restarting a logical partition
You can restart an AIX, Linux, or IBM i logical partition remotely by using the Hardware Management Console (HMC) command-line interface. You can also restart a partition that supports the simplified version of the remote restart capability. You can run up to four concurrent remote restart operations for a destination server. When the HMC is at version 8.5.0 or later, you can run up to 32 concurrent remote restart operations for a destination server. - Viewing the details of a remote restart operation
You can view the details of a remote restart operation of an AIX, Linux, or IBM i logical partition, or the server by using the Hardware Management Console (HMC) command-line interface. - Aborting a remote restart operation
You can abort or cancel a remote restart operation of an AIX, Linux, or IBM i logical partition by using the Hardware Management Console (HMC) command-line interface. - Recovering a remote restart operation
If a remote restart operation of an AIX, Linux, or IBM i logical partition fails, the Hardware Management Console (HMC) attempts an auto recover operation. When the auto recover operation fails, you can recover a remote restart operation by using the HMC command-line interface. - Creating a logical partition with Virtual Trusted Platform capability
You can create an AIX logical partition with Virtual Trusted Platform Module (VTPM) capability by using the Hardware Management Console (HMC). HMC Version 7.7.4 or later, provides an option to enable a VTPM on the logical partition when the logical partition is created. The HMC also provides an option to enable a VTPM on a running logical partition. - Enabling and disabling a Virtual Trusted Platform Module on a logical partition
You can enable a Virtual Trusted Platform Module (VTPM) on a logical partition by using the Hardware Management Console (HMC), after the logical partition is created. - Viewing the Virtual Trusted Platform Module settings
You can view the advanced Virtual Trusted Platform Module (VTPM) settings by using the Hardware Management Console (HMC). - Creating additional partition profiles
You can create more than one partition profile for a logical partition using the Hardware Management Console (HMC). Each partition profile can specify a different amount of system resources and different logical partition startup attributes. You can change the attributes used by a logical partition by shutting down the logical partition and restarting the logical partition using a different partition profile. - Creating a system profile
You can create a system profile using the Hardware Management Console (HMC). A system profile is an ordered list of partition profiles. When you activate a system profile, the managed system attempts to activate the partition profiles in the system profile in the order in which the partition profiles are listed. - Creating an AIX logical partition that uses IBM i virtual I/O resources
You can create an AIX logical partition that uses IBM i virtual I/O resources on servers that are managed by a Hardware Management Console (HMC). This allows you to maximize utilization of the physical hardware and simplify the backup procedure for your managed system. - Creating an IBM i logical partition that uses IBM i virtual I/O resources
You can create an IBM i logical partition that uses IBM i virtual I/O resources on servers that are managed by a Hardware Management Console (HMC). This allows you to maximize utilization of the physical hardware and simplify the backup procedure for your managed system. - Creating a Linux logical partition that uses IBM i virtual I/O resources
You can create a Linux logical partition that uses IBM i virtual I/O resources on servers that are managed by a Hardware Management Console (HMC). This allows you to maximize utilization of the physical hardware and simplify the backup procedure for your managed system. - Designating the service logical partition for your managed system
The service logical partition is the IBM i logical partition on a server that you can configure to apply server firmware updates to the service processor or to the hypervisor. You can also use the service logical partition to communicate server common hardware errors to IBM. These abilities are useful if the Hardware Management Console (HMC) is undergoing maintenance or is otherwise unable to perform these functions. - Resetting the managed system to a nonpartitioned configuration
You can use the Hardware Management Console (HMC) and the Advanced System Management Interface (ASMI) to erase all of your logical partitions and reset the managed system to a nonpartitioned configuration. When you reset the managed system, all of the physical hardware resources are assigned to a single logical partition. This allows you to use the managed system as if it were a single, nonpartitioned server. - Deleting a logical partition
You can use the Hardware Management Console (HMC) to delete a logical partition and all of the partition profiles associated with the logical partition.