Map location codes to hardware.
For address information, see Addresses – model 561 and 570.
Use the following illustrations to help you map a location code to a position on the server.
Use the following illustration to map a node location when you are working with a multiple node installation. All of the nodes have the same location codes inside the system unit; only the serial number is different (Utttt.mmm.sssssss-).
Use the following illustration to help you identify parts of the control panel.
Number | Name | Description |
---|---|---|
1 | Display | Displays current status of system startup, or diagnostic information in the event of a hardware problem. |
2 | Front serial port | Port uses RJ-45 connector. Use to plug in external devices at the front of the system unit. |
3 | Increment up | Scrolls the information in the display up. |
4 | Enter | Enter |
5 | Increment down | Scrolls the information in the display down. |
8 | System reset button | Resets the system |
9 | Power LED | Blinking - When connected to the power source
(System is in standby mode). Solid - When power button has been pressed.
Note: There is approximately a 30-second transition period from the
time the power-on button is pressed to when the power LED goes from
blinking to on solid. During the transition period, you may observe
the blinking intervals speed up.
|
10 | Power-on button | Turns the system power on and off. |
11 | Service processor reset switch (pinhole) | Service Personnel Use |
12 | Serial number label | Displays the system serial number |
The following table contains location codes for the parts that make up the server.
Failing item name | Symbolic failing item name | Physical location code | Identify LED | Link to part number | Failing item removal and replacement procedures |
---|---|---|---|---|---|
System unit | Un | NA | NA | ||
Fans | |||||
Fan 1 | Un-A1 | Yes | Part assembly diagrams | Fan | |
Fan 2 | Un-A2 | Yes | Part assembly diagrams | Fan | |
Power supplies | |||||
Power supply 1 | PWRSPLY | Un-E1 | Yes | Power parts | Power supply |
Power supply 2 | PWRSPLY | Un-E2 | Yes | Power parts | Power supply |
Backplanes | |||||
Input/output backplane with embedded:
|
CLCKMOD |
Un-P1 | Yes | 28DA 7733 (used only with 2.2 GHz processor ) | I/O backplane |
SCSI controller 1– bus 0 | Un-P1-T12 | ||||
SCSI controller 1– bus 1 | Un-P1-T13 | ||||
SCSI controller 2– bus 0 | Un-P1-T14 | ||||
IDE controller | Un-P1-T15 | ||||
Passthru card | Provides connection for VPD card, system ports, and SPCN | 25F8 | |||
I/O backplane assembly | NODEPL | Un-P1 | Yes | 28DA 7733 (used only with 2.2 GHz processor ) | I/O backplane |
System processor backplane | MEMBRD | Un-P2 | 27AE | System backplane | |
Disk drive backplane | Un-P3 | Yes | 28DB | Disk drive enclosure | |
SCSI/IDE card | Un-P3-C1 | 180A | SCSI-IDE converter card | ||
Media drive backplane | Un-P4 | Yes | 28DC | Media device enclosure | |
Ports | |||||
system port 2 (back of system unit) | Un-P1-T1 | NA | |||
system port 1 (back of system unit) | Un-P1-T2 | NA | |||
S1 system port (front of control panel) | Un-P1-T2 | NA | |||
Rack indicator connector | Un-P1-T3 | NA | |||
Integrated 2-port USB port 1 (AIX or Linux only) | Un-P1-T4 | NA | |||
Integrated 2-port USB port 2 (AIX or Linux only) | Un-P1-T5 | NA | |||
Integrated dual 1 GB Ethernet controller-port 1 | Un-P1-T6 | NA | |||
Integrated dual 1 GB Ethernet controller-port 2 | Un-P1-T7 | NA | |||
RIO/HSL left connector | HSL_LNK |
Un-P1-T8 | Yes | External cables | RIO/HSL cables (concurrent) |
RIO/HSL right connector | HSL_LNK |
Un-P1-T9 | Yes | External cables | RIO/HSL cables (concurrent) |
System cable connector | Un-P1-T10 | NA | |||
Processor and processor regulator | |||||
Processor card 1 | MEMCTLR |
Un-P2-C1 | Yes | Processor parts | System processor |
Processor card 2 | MEMCTLR |
Un-P2-C2 | Yes | Processor parts | System processor |
SMP processor cable | Un-P2-C1-T1 and Un-P2-C2-T1 | Model 561 and 570 cables | SMP processor cable | ||
Temperature sensor | Un -P2-C1 and Un -P2-C2 | Processor parts | System processor | ||
Voltage regulator 1 | Un-P2-C3 | Yes | Power parts | Voltage regulator card assembly | |
Voltage regulator 2 | Un-P2-C4 | Yes | Power parts | Voltage regulator card assembly | |
Voltage regulator 3 | Un-P2-C5 | Yes | Power parts | Voltage regulator card assembly | |
VPD card | Un-P1-T10 | VPD parts | VPD card | ||
Service processor | |||||
Service processor card | SVCPROC | Un-P1-C8 | Yes | 28EA | Service processor assembly |
Service processor cable | I2CBUS | Un-P1-T10 | Model 561 and 570 cables | Service processor cable | |
Time-of-day (TOD) | Un -P1-C8 | 28EA | Service processor assembly | ||
Time-of-day Battery | TOD_BAT | Un-P1-C8-E1 | Power parts | Service processor time-of-day battery | |
HMC 1 connector | Un-P1-C8-T1 | NA | |||
HMC 2 connector | Un-P1-C8-T2 | NA | |||
SPCN 0 connector | Un-P1-C8-T3 | NA | |||
SPCN 1 connector | Un-P1-C8-T4 | NA | |||
Adapters | |||||
PCI adapter in slot 1 | PIOCARD |
Un-P1-C1 | Yes | System parts | PCI adapter |
PCI adapter in slot 2 | PIOCARD |
Un-P1-C2 | Yes | System parts | PCI adapter |
PCI adapter in slot 3 | PIOCARD |
Un-P1-C3 | Yes | System parts | PCI adapter |
PCI adapter in slot 4 | PIOCARD |
Un-P1-C4 | Yes | System parts | PCI adapter |
PCI adapter in slot 5 | PIOCARD |
Un-P1-C5 | Yes | System parts | PCI adapter |
PCI adapter in slot 6 | PIOCARD |
Un-P1-C6 | Yes | System parts | PCI adapter |
RIO/HSL |
SI_CARD |
Un-P1-C7 | Yes | System parts | RIO/HSL adapter/InfiniBand host channel adapter |
RIO/HSL adapter connector | HSL_LNK |
Un-P1-C7-T1 | Yes | External cables | RIO/HSL cables (concurrent) |
RIO/HSL adapter connector | HSL_LNK |
Un-P1-C7-T2 | Yes | External cables | RIO/HSL cables (concurrent) |
Dual channel SCSI RAID enablement card | Un-P1-C9 | 5709 | RAID enablement card | ||
PCI bridge set 1 | BRDGSET |
Un-P1 | 28DA 7733 (used only with 2.2 GHz processor ) | I/O backplane | |
PCI bridge set 2 | BRDGSET |
Un-P1 |
Replace the I/O backplane and cards using the removal and replacement procedures corresponding to the locations indicated. | ||
PCI bridge set 3 | BRDGSET |
Un-P1 |
Replace the I/O backplane and cards using the removal and replacement procedures corresponding to the locations indicated. | ||
Memory modules | |||||
Memory module 1 | MEMDIMM | Un-P2-C1-C1 | Yes | Memory parts | Memory module |
Memory module 2 | MEMDIMM | Un-P2-C1-C2 | Yes | Memory parts | Memory module |
Memory module 3 | MEMDIMM | Un-P2-C1-C3 | Yes | Memory parts | Memory module |
Memory module 4 | MEMDIMM | Un-P2-C1-C4 | Yes | Memory parts | Memory module |
Memory module 5 | MEMDIMM | Un-P2-C1-C5 | Yes | Memory parts | Memory module |
Memory module 6 | MEMDIMM | Un-P2-C1-C6 | Yes | Memory parts | Memory module |
Memory module 7 | MEMDIMM | Un-P2-C1-C7 | Yes | Memory parts | Memory module |
Memory module 8 | MEMDIMM | Un-P2-C1-C8 | Yes | Memory parts | Memory module |
Memory module 1 | MEMDIMM | Un-P2-C2-C1 | Yes | Memory parts | Memory module |
Memory module 2 | MEMDIMM | Un-P2-C2-C2 | Yes | Memory parts | Memory module |
Memory module 3 | MEMDIMM | Un-P2-C2-C3 | Yes | Memory parts | Memory module |
Memory module 4 | MEMDIMM | Un-P2-C2-C4 | Yes | Memory parts | Memory module |
Memory module 5 | MEMDIMM | Un-P2-C2-C5 | Yes | Memory parts | Memory module |
Memory module 6 | MEMDIMM | Un-P2-C2-C6 | Yes | Memory parts | Memory module |
Memory module 7 | MEMDIMM | Un-P2-C2-C7 | Yes | Memory parts | Memory module |
Memory module 8 | MEMDIMM | Un-P2-C2-C8 | Yes | Memory parts | Memory module |
Note: First quad of memory
modules is plugged into memory module slots P2-Cx-C1, P2-Cx-C3, P2-Cx-C6,
and P2-Cx-C8. Second quad of memory modules is plugged into memory
module slots P2-Cx-C2, P2-Cx-C4, P2-Cx-C5, and P2-Cx-C7.
|
|||||
Device physical locations | |||||
Disk drive 1 | Un-P3-D1 (logical location with RAID card Un-P1-T13-L5-L0, logical location without RAID card Un-P1-T14-L5-L0) | Yes | Disk unit parts | Disk drive | |
Disk drive 2 | Un-P3-D2 (logical location with RAID card Un-P1-T13-L4-L0, logical location without RAID card Un-P1-T14-L4-L0) | Yes | Disk unit parts | Disk drive | |
Disk drive 3 | Un-P3-D3 (logical location with RAID card Un-P1-T13-L3-L0, logical location without RAID card Un-P1-T14-L3-L0) | Yes | Disk unit parts | Disk drive | |
Disk drive 4 | Un-P3-D4 (logical location with RAID card Un-P1-T12-L5-L0, logical location without RAID card Un-P1-T12-L5-L0) | Yes | Disk unit parts | Disk drive | |
Disk drive 5 | Un-P3-D5 (logical location with RAID card Un-P1-T12-L4-L0, logical location without RAID card Un-P1-T12-L4-L0) | Yes | Disk unit parts | Disk drive | |
Disk drive 6 | Un-P3-D6 (logical location with RAID card Un-P1-T12-L3-L0, logical location without RAID card Un-P1-T12-L3-L0) | Yes | Disk unit parts | Disk drive | |
IDE drive 1 | Un-P4-D1 | Yes | Removable media device parts | Media device | |
IDE drive 2 for 570 | Un-P4-D2 | Yes | Removable media device parts | Media device | |
Control panel | |||||
Control panel (bottom media bay) | Un -D1 | 28D4 | Control panel | ||
Server firmware | |||||
Server firmware | Un-Y1 |
Multi-adapter bridge domain / Peripheral Component Interconnect (PCI) bridge set | IOA assignment rules |
---|---|
Adapters embedded in -P1 planar (no IOP) | Embedded SCSI, embedded Ethernet |
C1 - C2 | Embedded SCSI, C2 |
C3 - C6 | C4, C5, C6 |