How to NOT connect an SVC in a core-edge Brocade fabric
seb_ 060000QVK2 Comments (18) Visits (29983)
In one of my previous posts I wrote about "Why inter-node traffic across ISLs should be avoided". There is an additional "bad practice" that could lead to performance problems in the host-to-SVC traffic.
Let's imagine a core-edge fabric. A powerful switch (or director) in its center is the core. The SVC and its backend storage subsystems are directly connected to it. Beside of that there are also the ISLs to the edge switches where the hosts are connected to. As there is an SVC in the fabric, all host traffic usually goes to the SVC and the SVC is the only host of all other storages. From time to time I see a cabling like the one below. The devices are connected in a common pattern. For example SVC ports are always on port 0, 4, 8, ... or for a director for example on port 0 and 16 on each card... Something like that. The reason behind that is often to spread the workload over several cards/ASICs to minimize impact in case of a hardware failure. But there's a risk in doing so.
Index Port Address Media Speed State Proto ====
The SAN perspective
In the situation described above, all host traffic is passing the ISLs from the edge switches to the core. ISLs are logically "partitioned" into so called virtual channels. Of course the ISL is still just one fibre and only one signal is passing it physically at the same time. The virtual channels are just portions of buffer credits dedicated and the decision which virtual channel a frame takes - and therefore which portion of the buffers credits it uses - is made by looking into the destination fibre channel address.
Technical deep dive
A normal non-QOS ISL has 4 virtual channels for data traffic. For an 8G link each one of them has 5 buffers. They can only work with these 5 buffers and there is no possibility to "borrow" some out of a common pool like for QoS links. With the command "portregshow" you can see the buffer credits assigned to the virtual channels (I added the first line):
VC 0 1 2 3 4 5 6 7 0xe6692400: bbc_trc 4 0 5 5 5 5 1 1
Only VCs 2-5 are used for data traffic. This makes 20 usable buffers which normally should be enough for a normal multimode connection between two switches in the same room with only some metres cable length. Basically the switch uses the last two bits of the second byte of the destination address. That looks so:
So where's the problem now?
In our imaginary core-edge fabric where for example all SVC ports are connected to ports 0 (bin 00), 4 (bin 100), 8 (bin 1000), 12 (bin 1100) , ... all host I/O towards SVC would use the same virtual channel. As this is the only traffic that passes the ISLs from edges to cores, only a quarter of the buffers are actually used! 5 buffers are very heavy in use and 15 are idling around never to be filled. And 5 buffers are actually pretty few for an edge switch full of hosts wants to speak with the core switch where the SVC is connected. The result would be credit starvation and congestion on a virtual channel level.
How to solve that?
There are 3 possibilities:
1.) You could re-cable your SAN in a manner that all VCs are used. But beside of the risk of physical problems and problems introduced by maintenance actions the devices have to learn about the new addresses of the SVC ports. For many operating systems this still means reboots or reconfigurations. It could involve a lot of work and risk for outages.
2.) You could just change the addresses with the portaddress command. This command is usually used in the virtual fabric environment and if you can use it depends on installed firmware and used platform. While it avoids the physical actions, it still has the disadvantages for the hosts because of changed addresses.
3.) The best and least interrupting possibility might be to set the ISLs to LE mode. This is the long distance mode dedicated for links under 10km in length. It will not only put more buffers on the link (40 for user traffic in an 8G link compared with the 20 for a normal 8G E-Port) but will also collapse the 4 user traffic VCs to just one. It looks like this then:
VC 0 1 2 3 4 5 6 7 0xe6602400: bbc_trc 4 0 40 0 0 0 1 1
So all buffers and therefore also all buffer credits will be used by the hosts and nothing idles. There will of course be a short interruption while changing the ISL to LE mode but beside of that nothing changes for the hosts, because all the addresses stay the same. This is clearly the way to go in the situation described above.
Just something strange for the end: Some switches are delivered from manufacturing with an alternative addressing pattern. For example port 1 of domain 3 won't have the address 030100 then but something like 030d00. In that case the problem can happen similarly but on other ports. But using LE-mode would solve it in the pretty same way.
Please keep in mind that the whole article relates to a very special (although very common) SAN layout in an SVC-centered environment. This is clearly not a standard action plan for all performance problems but it could help if you have a customer in a situation like this. For any questions, feel free to contact me.
Additionally, please be aware that this is not an SVC problem by itself but will happen with every central storage connected to a switch using a pattern as described above and being used by hosts connected to another switch over an ISL!
Update from May 9th:
I was made aware that readers of this article queried their vendors, maintenance providers or business partners with the idea to just set all their ISLs to LE-mode regardless if the condition as described above is actually met. Because of that, I would like to state more clearly: Using LE-mode as a general approach for your ISLs can cause severe problems!
If the SVC ports are not connected in a way that only one Virtual Channel would be used, it actually makes sense to have ISLs with more than one VC. Virtual Channels are a good feature to prevent that a latency bottleneck due to back pressure impairs the traffic of all devices using the same ISL. If devices on the edge switches communicate with other devices connected to other ports of the core (or other edges) as well, the impact of using LE-mode would be even more extreme in the case of slow drain devices.
I made some drawings to illustrate this. The first one shows 1 normal ISL between the edge and the core. You can see the 4 VCs used for data traffic. (I left out the other VCs for better visibility):
Here host 1 and 2 make traffic against the SVC (green), host 3 against an additional disk subsystem (purple) and host 4 against a tape drive (orange). Based on the ports these devices are connected to, other VCs are used for that traffic.
If you would use an LE-port instead, it would look like this:
Now all 4 data traffic VCs collapsed to a single one. As long as everything runs smoothly, you won't see an impact.
Buf if for example one of the devices connected to the core is slow draining, following will happen most probably:
In the picture above the purple disk is a slow drain device. Due to back pressure the whole ISL will be a latency bottleneck, because all data traffic shares the same VC in LE-mode. The back pressure goes further towards the edge switch and all 4 hosts of our example are affected now although only host 3 communicates with the slow drain device!
With a normal E-port it looks like this:
Now only VC4 is affected while VC2, 3 and 5 are running smoothly, because they have their own, unaffected buffer management. Therefore only host 3 will face a performance problem while the hosts 1, 2 and 4 are running fine.
You see: Using LE-mode for the purpose described in my original article does only make sense if these special conditions are really met. In all other cases it can impair the SAN performance tremendously!