Explanation
This message is the first in a group of messages
that VTAM® issues when an identification
exchange (IDX) device failed to initialize. A complete description
of the message group follows.
IST1650I IDX INITIALIZATION FAILED FOR trlename DEVICE device_number CODE code
IST1651I IDX RECEIVED BY VTAM:
IST1574I offset hexdata_1 hexdata_2 hexdata_3 hexdata_4 EBCDIC_data
⋮
IST1574I offset hexdata_1 hexdata_2 hexdata_3 hexdata_4 EBCDIC_data
IST1652I IDX SENT BY VTAM:
IST1574I offset hexdata_1 hexdata_2 hexdata_3 hexdata_4 EBCDIC_data
⋮
IST1574I offset hexdata_1 hexdata_2 hexdata_3 hexdata_4 EBCDIC_data
IST314I END
IST1650I
VTAM issues this message while
processing an OPENPATH request unit when initializing an identification
exchange (IDX) with a device, such as the IBM® S/390® Open
Systems Adapter or a HiperSockets™ (iQDIO)
adapter. - The trlename value is the name of the device,
as defined on the TRLE definition statement in the TRL major node
or dynamically created in the ISTTRL major node.
- The device_number value is the hexadecimal
address of the WRITE or READ subchannel, as defined on the WRITE or
READ operand on the TRLE definition statement in the TRL major node.
- The code value is a 1-byte hexadecimal value
that indicates the reason that the device failed to initialize. The code value
is one of the following:
- If the code value is less than X'80',
it is a code that is generated by the OSA or the HiperSockets adapter. See the OSA IDX failure return codes information in zEnterprise System and System z10 OSA-Express
Customer's Guide and Reference for a description of the failures generated
by the OSA. Contact the IBM Software
Support Center for failures generated by the HiperSocket adapter.
- If the code value is greater than or equal
to X'80', then that code is byte 3 of a data link control
(DLC) status code that describes the error. Byte 2 of the DLC status
code that describes this type of error is X'40'. Together,
bytes 2 and 3 of a DLC status code form the completion code. For example,
if code is X'80', this error is documented as completion
code X'4080'. See the completion
code information in z/OS Communications Server: IP and SNA Codes for a description of the completion code.
IST1574I - This message displays the IDX received from (if preceeded by
message IST1651I) or sent to (if preceded by message IST1652I) the
IDX device.
- offset is the hexadecimal offset in the IDX.
- hexdata_1, hexdata_2, hexdata_3 and hexdata_4 each
display 4 bytes of the IDX in hexadecimal format.
- EBCDIC_data displays 16 bytes of the IDX in
EBCDIC format. Unprintable characters are represented by periods.
IST1651I - This message is a header for the information displayed in message
IST1574I for the IDX received from the IDX device.
IST1652I - This message is a header for the information displayed in message
IST1574I for the IDX sent by VTAM to
the IDX device.
System action
The IDX connection is not established.
Operator response
Save the system log and print the TRL major
node definition for problem determination.
For code 8B
(insufficient storage), wait a short time and reenter the command.
If VTAM continues to issue
this message, enter the DISPLAY STORUSE and DISPLAY CSM commands.
Save the system log and dump for problem determination.
System programmer response
For code 82, verify
that the subchannel address in the I/O generation and in the TRL major
node are correct.
For
code 8B (insufficient
storage):
For code 8C, verify that the TRL major
node name is configured correctly in the IDX device.
For an
apparent software problem, take the following actions:
- If you have access to IBMLink, search for known problems with similar
symptoms. If no applicable matches are found, report the problem
to IBM using the Electronic
Technical Report (ETR) option on IBMLink.
- If you do not have access to IBMLink, report the problem to the IBM software support center.
Routing code
Descriptor code