Don't shoot the messenger - The error 1370
seb_ 060000QVK2 Comments (10) Visits (32274)
The Storwize V7000 and the SVC (SAN Volume Controller) share the same code base and therefore the same error codes. Many of them indicate a failure condition in this very machine, but there are others just pointing to an external problem source. The error 1370 is one of the second kind. There is not really much information about it in the manuals but in fact it could give you a good understanding about what's going wrong.
As storage virtualization products the SVC and the V7000 - if you use it to virtualize external storage - are actually the hosts for the external storage. Speaking SCSI they are the initiators and the external backend storage arrays are the targets. Usually the initiators monitor their connectivity to the targets and do the error recovery if necessary. And so the SVC and the V7000 focus on monitoring the state of their backend storage and can actually help you to troubleshoot them.
So you have 1370 errors, what now?
They come in two flavors: The event id 010018 (against an mdisk) and the event id 010030 (against a controller - aka storage array). I'll explain the 010030 as it's easier to understand but understanding it will give the insight to understand the 010018, too.
If you double-click the 1370 in your event log, you see the details of the error:
You see the reporting node and the controller the error is reported against. But the most important thing is the KCQ. The Sense Key - Code - Qualifier.
Imagine this situation: The SVC is the initiator. It sends an I/O towards the storage device - the target. But the target faces a "note-worthy" condition at the very moment. So it will make the initiator aware of it by sending a so called "check condition". As curious as it is, the initiator wants to know the details and requests the sense data. These sense data will now be stored in - you already guess it - a 1370 in the format Key - Code - Qualifier. Often the last both are referred to as ASC (Additional Sense Code; the green one) and ASCQ (Additional Sense Code Qualifier; the blue one).
Where's the Rosetta Stone?
These sense data can be translated using the official SCSI reference table by Technical Commitee T10 (the council making the SCSI protocol). If you encounter an ASC/ASCQ combination in a 1370 that can't be found in that list, it's most probably a vendor specific one. In that case the manufacturer of the target device could give you more information about it.
Back to our example. So you see the ASC 29 (the "Code") and the ASCQ 00 (the "Qualifier") here. Looking that up in the list reveals: It's a "POWER ON, RESET, OR BUS DEVICE RESET OCCURRED". This so called "POR" should make you aware that the target was recently either powered on or did a reset. Usually the initiator gets this with the first I/O it does against the target after such an event, to be aware that any open I/O it has against this target is voided and has to be repeated.
Ah, okay. That's it?
No! You see the orange box? This is the time since this sense data was received. The unit is 10ms, so this number actually represents a long time since there really was a POR for this controller.
So why do we have a 1370 today?
The 1370 is more of a container for sense data. The number behind the attributes show the "slot". So the information visible here are for the first slot and as such a long time passed since it occurred it's meaningless for us now. Let's scroll down a bit:
In the second slot you see what's really going wrong within the external storage device at the moment, because the time value is 0. That means the 1370 was triggered because of it. And it contains a different set of sense data. ASC 0C / ASCQ 00! If you try to look it up in the list, you will find 0C/00, but hey - this cannot be! The combination 0C/00 means "WRITE ERROR", but it's not defined for "Direct Access Block Devices" like storage arrays.
A Dead End?
No, of course not. In this example the storage is a DS4000. Just download the DS4000 Problem Determination Guide and it will provide an ASC/ASCQ table. Here you'll see that 0C 00, together with the Sense Key 06 (the red circle) means "Caching Disabled - Data caching has been disabled due to loss of mirroring capability or low battery capacity."
Running without the cache in the backend storage could lead to severe performance degradation and should definitely be troubleshooted! Without even looking into the backend storage you already know what's going wrong there! No need to involve SVC or V7000 support this time. Just focus on the backend storage and find out why the caching is disabled.
So please don't shoot this messenger, it just tries to help you!
Update - December 2nd 2013
The SCSI Interface Guide for IBM FlashSystem can be found here.