0A5

Explanation
The system detected a logic error in one of the
hardware configuration definition (HCD) modules.
The right-most
four bytes of the program status word (PSW) have the following format: xrrr0www
 where: x
Irrelevant information.
rrr
A hexadecimal reason code indicating the reason for the failure.
www
The wait state code.

 The reason code (rrr) is one of the
following: 070
Two UIMs made multiple attempts to build a GIT. The first UIM
is flagged as in error.
071
Two UIMs specified the same generic preference value. The last
UIM is flagged as in error.
072
A UIM defines a generic device type with a compatible list that
contains duplicate entries.
073
Two UIMs made multiple attempts to build a CIT for the indicated
control unit. The first UIM is flagged as in error.
074
A UIM specified an non-valid device number in DFP. Message reason code 1: The device number in the DFP is greater
than the maximum allowed device number.
Message reason code 2: A DFT exists already for the device number
specified in the DFP.

075
A UIM specified either in the DFP or UIP a generic name for which
the GIT could not be found. The indicated UIM is flagged as in error.
076
The indicated UIM specified more than 5 MLT names or specified
no MLT names. The indicated UIM is flagged as in error.
077
The indicated UIM specified more than the 256 bytes of device-dependent
information. The indicated UIM is flagged as in error.
078
The indicated UIM specified an non-valid UCB segment type for
an ACON position pointer. The indicated UIM is flagged as in error.
079
The indicated UIM specified an non-valid UCB segment type for
an ACON relocation pointer. The indicated UIM is flagged as in error.
080
The indicated UIM specified an offset for an ACON position pointer
that is not within the specified UCB segment. The indicated UIM is
flagged as in error.
081
Two UIMs made multiple attempts to build a UIT for the indicated
device. The first UIM is flagged as in error.
082
The indicated UIM specified more than 24 bytes of device-dependent
segment data. The indicated UIM is flagged as in error.
083
The indicated UIM specified a device number greater than the maximum
allowed device number. Message reason code 1: Device number in the relocation information
is greater than the maximum allowed device number.
Message reason code 2: Device number in the device class extension
area is greater than the maximum allowed device number.

 The indicated UIM is flagged as in error.
084
The indicated UIM specified an non-valid device class in the DFPTBYT3
field. The indicated UIM is flagged as in error.
085
The DCT information specified for a DASD does not match the previously
specified information for this DASD type.
086
A UIM specified a DCT entry length greater than the allowed maximum.
087
Insufficient space in DCT for current DCT entry.
088
The indicated UIM tried to build a CIT by passing a CIP that does
not specify an attachable device list.
091
The indicated generic name as specified in the list of compatible
generics could not be found in the list of GITs. The first indicated
generic is deleted from the list of compatible generics. The UIM is
flagged as in error.

System action
The system enters wait state X'0A5'.
The system issues the following hardware configuration definition
(HCD) messages with the following wait state reason codes: Code
Accompanying Message
070
CBDA070I, to display the UIM name and the generic name.
071
CBDA071I, to display the UIM name and the generic names.
072
CBDA072I, to display the UIM name and the generic name.
073
CBDA073I, to display the UIM name and the control unit type/model.
074
CBDA074I, to display the UIM name, device number, and reason code.
075
CBDA075I, to display the UIM name and the DFP or UIP, as applicable.
076
CBDA076I, to display the UIM name.
077
CBDA077I, to display the UIM name.
078
CBDA078I, to display the UIM name and UCB segment type.
079
CBDA079I, to display the UIM name and the UCB segment type.
080
CBDA080I, to display the UIM name.
081
CBDA081I, to display the UIM names and the device type/model.
082
CBDA082I, to display the UIM name.
083
CBDA083I, to display the UIM name, device number, and reason code.
084
CBDA084I, to display the UIM name, device number, and Ucbtype3.
085
CBDA085I, to display the DASD type.
086
CBDA086I, to display the UIM name.
087
CBDA087I.
088
CBDA088I, to display the UIM name and control unit type/model.
091
CBDA091I, to display the generic names.

Operator response
Notify the system programmer. If requested
by the system programmer, obtain a stand-alone dump.

System programmer response
Search problem reporting databases
for a fix for the problem. Use the following search argument: WS/D0A5: Wait state code
PRCS/hhhhhhhh: Reason code
PIDS/name of UIM: Program name
VALU/Ccccccccc: Message variable text

 If no fix exists, ask the operator to obtain the stand-alone
dump. Contact the IBM® Support
Center. Provide the stand-alone dump, the UIM name, if available,
and the accompanying message. 

Source
Hardware configuration definition (HCD)