TS4300 Fix Readme

                        ===================================================================================================
                        Firmware Level: 1.5.0.0-A00
                        Release Date: 12/03/21
                        ===================================================================================================
                        New Features:
                        - LTO9 tape drive support
                        Fixes:
                        - Fixed issue where LDAP settings were not reset when resetting library to default configuration
                        - Multiple Help pages updates
                        - Fixed issue where events time was inconsistent with library time
                        - Fixed issue where SNMPv1 does not handle multiple community names
                        - Fixed issue where web sessionID was not regenerated
                        - Fixed issue missing events reported to rsyslog server in case TCP RST has been occurred
                        ===================================================================================================
                        Firmware Level: 1.4.1.0-B00
                        Release Date: 05/31/21
                        ===================================================================================================
                        New Features:
                        - None
                        Fixes:
                        - Documentation improvements for library and drive diagnostics
                        - Fixed issue where non admin users were not allowed to change their password
                        - Fixed issue where TA28d was not reported for redundant power supply failure
                        - Fixed issue where TA flags where not triggered for SCSI
                        - Fixed issue where an event was not reported for an elevator blocked
                        ===================================================================================================
                        Firmware Level: 1.4.0.0-A00
                        Release Date: 09/07/20
                        ===================================================================================================
                        New Features:
                        - None
                        Fixes:
                        - Added a survey to provide feedback to IBM
                        - Added Drive Test option in dropdown menu in Drives page
                        - Improved event handling for the condition where the Robotic Lock Lever is not fully locked or unlocked
                        - Fixed issue where default superuser comes back after firmware upgrade
                        - Fixed issue where incorrect default users were restored from an old backup file
                        - Fixed LDAP issue where when a wide DN is set, several files are shown as if they were regular users
                        - Fixed issue where a firmware downgrade over REST fails
                        - Fixed issue where SNMP app fails with "UNINTENDED TERMINATION" error
                        - Fixed LDAP issue where if adding a Server with an autocomplete password could lead to invalid command parameter
                        - Fixed LDAP issue where users were not added when the group is in a sub folder
                        ===================================================================================================
                        Firmware Level: 1.3.0.1-A00
                        Release Date: 12/06/19
                        ===================================================================================================
                        New Features:
                        - None
                        Fixes:
                        - Fixed issue where IO slots were shown on OP panel in source and destination after being removed
                        - Updated error message when not compliant password was used for first login password change
                        - Added control card SN to library logs
                        - Fixed initial configuration wizard issue when default admin was removed
                        - Fixed issue where wrong severity was assigned for move cartridges problems
                        - Fixed issue where an incorrect behavior for move media was shown when there was no tape in library
                        ===================================================================================================
                        Firmware Level: 1.3.0.0-D00
                        Release Date: 08/16/19
                        ===================================================================================================
                        New Features:
                        - None
                        Fixes:
                        - Improved login security
                        - Added ability to move cartridges from the operator panel
                        - Added SNIA MIB file
                        - Fixed issue where KMIP Connectivity Check can take longer that RMI autologout
                        - Fixed issue where an invalid configuration did not report the proper error
                        - Fixed issue where custom certificate backup failed with "internal software error" message
                        - Fixed issue where SKLM z/OS does not work with IPv6 link local address
                        - Fixed issue where RMI and OCP report different drive encryption status
                        - Improvements for sequential mode operation
                        - Fixes for CVE-2018-20679 and CVE-2019-5489 vulnerabilities
                        - Fixed issue where the state of drive is shown as Idle during drive initialization
                        - Fixed issue where event 4154 is logged when certificate is invalid
                        - Fixed issue where SSL Create Custom Certificate Wizard fails to generate CSR if hostname is too long
                        - Fixed issue where IPv6 DNS does not work for SMTP server
                        ===================================================================================================
                        Firmware Level: 1.2.1.0-A00
                        Release Date: 12/10/18
                        ===================================================================================================
                        New Features:
                        - 40 Slots Accessor support
                        Fixes:
                        - Improvements for auto calibration
                        - Upgrade of Unzip from 5.52 to 6.00
                        - Upgrade of Lighttpd to apply security fixes
                        - Fixed issue where Robotic cycle counter is reset to 0 in Robotic NVM
                        - Fixed issue where no event is logged about robotic movement problem after failed autocalibration
                        - Fixed issue where no event is generated when trying to update drive FW when library is busy
                        - Fixed issue where no ticket is created for failed pre-inventory initialization
                        - Fixed issue where data is written unencrypted after switching from KMIP -> SKLM -> KMIP
                        - REST - Fixed issue where it's not possible to unlock mailslot with user/monitor account
                        - Fixed issue where no Warning Event 4018 was generated after a wrong Drive FW upgrade
                        - Fixed issue where power shutdown starts after 10 seconds although up/down buttons are still pressed on the OCP
                        - Fixed issue for SKLM z/OS with IPv6 link local address
                        - Fixed issue where tape VOLSER not showing up in sKLM logs when using KMIP
                        - Improvements of GUI Email (SMTP) Settings buttons
                        ===================================================================================================
                        Firmware Level: 1.2.0.0-B00
                        Release Date: 10/01/18
                        ===================================================================================================
                        New Features:
                        - SKLM for z/OS Encryption 
                        Fixes:
                        - Improvement of 3D View tooltip
                        - Improvement of validation message when adding users
                        - Improvement of the layout of Modify Port Settings dialog
                        - Improvement of recovery process when incorrect inventory
                        - Fixed issue where Expert/Basic Partition Wizard can be started with loaded drive
                        - Fixed issue where a Move a Tape by Web Interface into a non partition does not show a warning
                        - Fixed issue where library switches to Idle instead of Idle (Offline) during magazine wait period
                        - Fixed issue where queuing of more than 2 mailslot unlocks does not work
                        - Fixed spelling mistake in solution suggestion of Event 4158
                        - Fixed typo in troubleshooting steps for Event 4155
                        - Fixed issue where led is off after attempt to unlock mailslot when system is busy
                        - Fixed issue where library state changed to Offline for a long time after attempt to open partition wizard when mailslot is being unlocked
                        - Fixed REST issue where no error was returned after resetting the drive removed from library
                        - Fixed issue where wrong message is shown during disabling I/O slots
                        - Fixed issue where horizontal scroll bar appears, but it is unusable in OP Panel
                        - Improvement of log package
                        - Fixed problem where basic partition wizard can not be started with IE11
                        - Fixed issue where a blank popup was shown on modify port settings page
                        - Fixed problem where drive cleaning test could fail
                        - Fixed issue where a confirmation message is not shown after change SNMP settings
                        - Fixed issue where information about KMIP Server and encryption mode was not correct in system log
                        - Fixed issue where wrong message was shown when not valid hostname was used for SNMP Target
                        - Fixed issue where library got stuck in magazine-removed state after magazine removal and re-insertion
                        - Fixed issue where error event listing doesn't load most recent event
                        - Fixed problem where a locked user could login if another user changes the Password Rules to not lock out
                        - Fixed REST issue where Admin can get the list of service events
                        - Fixed REST issue where the text for service events is not correctly shown
                        - Fixed REST issue where Library status "Unit lock unlocked" is shown as "Unknown"
                        - Fixed REST issue where GET /rest/partition/information shows wrong LUN information
                        - Fixed issue KMIP Wizard during first configuration
                        - Fixed issue where move cycle counter in robotic is not correct after system restart
                        - Fixed LDAP Issue with using user names with parentheses
                        - Fixed typo in KMIP Wizard
                        - Fixed problem where Unit Auto Calibration Wizard stopped with timeout
                        - Fixed problem where OP Panel Pin was not set properly after Configuration File restore
                        - Fixed issue where Warning Event 4124 was shown during Demo Mode Test
                        - Fixed issue where library in Sequential Mode shows Idle (Offline) in red instead Idle in green
                        - Fixed problem where error event 2065 was shown during initialization
                        - Fixed Security Vulnerabilities CVE-2018-0732, CVE-2018-5733 and CVE-2018-5391
                        - Fixed problem where primary ports are disabled after drive FW upgrade by SCSI
                        - Fixed problem with insufficient memory when pulling library logs
                        ===================================================================================================
                        Firmware Level: 1.1.1.2-A00
                        Release Date: 04/30/18
                        ===================================================================================================
                        New Features:
                        - Support of sequential mode
                        Fixes:
                        - Improvement of GUI dialogs 
                        - Improvement of SSL signing wizard
                        - Improvement of I/O Station and Magazine timeout
                        - Improvement of KMIP wizard
                        - Fixed problem where a corrupted drive FW did not report an error during update
                        - Improvement of Basic Partition wizard
                        - Improvement of Logical Library wizard
                        - Improvement of SNIA-SML-MIB
                        - Fixed problem where IP and host name is not shown correctly in SNMP traps
                        - Fixed problem where some operations can be started while reset to defaults is in progress
                        - Improvement of Help information
                        - Fixed problem where GUI and OP panel could hang after the upload of custom certificate
                        - Fixed problem where clearing values of KMIP wizard does set the correct default values
                        - Improvement of IPv4 Network configuration in OP Panel
                        - Fixed problem where LTO8 drive could fail writing data if LME is enabled
                        - Fixed problem where KMIP setup could fail with I/O error
                        - Fixed problem where drives and slots configuration can be lost after configuring partition with KMIP 
                        - Fixed problem where self signed KMIP certificate does not work with SKLM v2.7
                        - Fixed problem where maximum number of partitions is incorrect in Expert Partition wizard
                        - Fixed problem where invalid characters can be saved for SMTP
                        - Improvements for LTO Type M cartridges management
                        - Fixed problem where Initial configuration wizard could fail in the Date & Time page
                        ===================================================================================================
                        Firmware Level: 1.1.1.1-B00
                        Release Date: 01/29/17
                        ===================================================================================================
                        New Features:
                        - Un-initialized M8 media support
                        Fixes:
                        - Fixed problem where user could set illegal values for date and time
                        - Improvement for Drive Tests wording
                        - Fixed issue where a cartridge in drive may not be reported in library inventory
                        - Fixed issue where a warning about an older FW is not shown when downgrading the library FW
                        - Improvement for events 2053 and 2054 troubleshooting
                        - Fixed problem where the Basic Partition Wizard could crash
                        - Fixed issue where naming of a resolved ticket is not correct
                        - Fixed issue where self signed certificate is not selected as default
                        - Fixed issue where Restore configuration button is active when no file was selected
                        - Fixed issue where wellness test status is not updated correctly
                        - Fixed problem where Domain name is not validated correctly
                        - Fixed problem where SMTP did not report a library reboot
                        - Fixed problem where login was not possible in Web Interface after unit to unit lock-unlock and power cycle
                        - Improvement for KMIP error message when using a not supported certificate
                        - Improvement for magazine button led handling
                        - Improvements for IO station management
                        - Improvements for Magazine management
                        - Fixed problem where if no reboot was made for factory reset, the library will stay in reserved state
                        - Fixed issue where incorrect encryption is shown in system log
                        - Fixed problem where drive encryption settings were not updated after logical library encryption update
                        - Fixed issue where an error pop up was not cleared when trying to change the port configuration while drive is powering up
                        - Fixed issue where the accessor could fall in a recovering loop after an accessor block
                        ===================================================================================================
                        Firmware Level: 1.1.1.0-A00
                        Release Date: 11/23/17
                        ===================================================================================================
                        New Features:
                        - LTO8 tape drive support
                        - Pre-initialized M8 media is supported with a minimum LTO8 tape drive firmware level of HB82
                        Fixes:
                        - Fixed problem where user has been logged out from Operator Panel without warning message.
                        - Fixed problem where no data validation was made in Manage Encryption wizard when adding a Signed Certificate 
                        - Fixed problem where  Move  button gets an incorrect color when clicked
                        - Fixed incorrect behavior of  Stop Test  button toggles to  Run  button immediately when Library Verify Test is aborted even though test is still processing
                        - Fixed issue with header time not matching Time Zone settings
                        - Fixed typo in Operator Panel drive diagnostics message
                        - Fixed message when no license is installed
                        - Fixed issue where  Retry  button does not refresh in the Management GUI after reboot from FW Upgrade
                        - Fixed unexpected response from REST Interface on invalid IO open request
                        - Fixed issue where Management GUI activity is short time changing to  scanning  and back idle
                        - Fixed issues with Auto Clean
                        - Fixed problem where no event is logged after failure during head test
                        - Fixed problem where wrong result is reported for Library test after Drive test failed
                        - Fixed issue when I/O button is pushed during movement into drive
                        - Fixed issue where no event is logged after drive test failed due to diagnostic cartridge placed into wrong I/O slot
                        - Fixed problem where library status is shown as Upgrading after a failed Upgrade
                        - Improvement of error handling when export of diag cartridge failed and new drive test is started
                        - Improvement of Start Test button by blocking it quickly after starting the test
                        - Improvement of Cartridge and Slots pages by inform which slots belong to I/O stations
                        - Fixed issue where an unhandled exception was thrown when having spooling problems
                        - Improvement for capitalization for text on buttons
                        - Fixed field name for LDAP wizard
                        - Fixed issue where status  Magazine removed  is not reported after powering on the unit with released magazine
                        - Improvement for message shown for incompatible drive error
                        - Fixed problem where library could enter in a loop after a system reboot from Operator Panel
                        - Improvement for event description for Cartridge found in inaccessible slot of lowermost slots
                        - Improvement for incompatible drive event handling
                        - Fixed problems with magazine button behavior in case of emergency stop condition
                        - Fixed occasional inventory scan problem if emergency stop condition occurs during magazine unlock
                        - Improvement for IO Station handling in the case of an Emergency stop during the magazine scan
                        - Fixed Management GUI hang issue during Drive Tests
                        - Fixed magazine button hang condition if pressed while media removal is prevented
                        - Improvement for description of "Drive was hot-removed" event
                        - Fixed issue where Operator Panel Display initialization was delayed up to 5s after power on
                        - Fixed problem where Wellness test failed on verification of power board instead of power supply
                        - Fixed issue where Magazine can be re-opened while locking
                        - Fixed problem where it was possible to configure not supported drives
                        - Fixed problem where the IO Station was not scanned after moving back into the unit
                        - Fixed problem where Autoclean did not work
                        - Improvement for License file management when non-CRU controller is put into non-CRU chassis
                        - Improvement for Management GUI main menu
                        - Fixed problem where Library Properties screen is shown empty
                        - Fixed problem where Magazine buttons were disabled after release timeout
                        - Fixed issue where empty hostname is not on Operator Panel
                        - Fixed issue where "Library Firmware changed" event was logged in Configuration Log after restoring configuration
                        - Fixed issue where Update button behaves incorrectly in Update Drive Firmware page
                        - Improvement for Reset Internal IP Range by adding a confirmation message
                        - Improvement for Ipv6 validation in Operator Panel
                        - Improvement for Ipv4 validation in Management GUI
                        - Fixed issue where an incorrect error pops up for "Cleaning tape expired" event
                        - Fixed problem where Operator Panel fail when downgrading Library Firmware
                        - Fixed issue where unlocked IO Station LED stops flashing when another IO Station is reinserted
                        - Fixed problem where IO Station handling hangs when a request to open magazine is made
                        - Fixed problem where Magazine is not scanned if delay of inventory scan occurs
                        - Improvement for Remote Logging with a confirmation dialog after navigation from Remote Logging page
                        - Fixed issue where an incorrect error is shown after Drive firmware update completes with Internet Explorer
                        - Improvement for login list when many users are available 
                        - Fixed an unexpected unit attention when trying to open Magazine while media removal prevented
                        - Improvement of troubleshooting steps for events 2053 and 2054
                        - Fixed issue with Kerberos when having users with the same name
                        - Fixed problem to load session after switch from SSL to not SSL
                        - Fixed problem where Personality is missing if system is in Startup Halted State
                        - Fixed incorrect title of Kerberos error popup
                        - Fixed issue where some valid symbols are not allowed in principal name for Kerberos
                        - Fixed issue where some valid symbols used in the realm name caused an "internal Software error" for Kerberos
                        - Fixed problem where deletion of user (principal) containing special chars was not impossible for Kerberos
                        - Fixed problem where Encryption key requests were not handled anymore after SCSI abort
                        - Fixed problem where it was not possible to read encrypted data
                        - Fixed problem where Superuser cannot clear KMIP config
                        - Fixed problem where KMIP certificates were removed from unit after disabling KMIP license
                        ===================================================================================================
                        Firmware Level: 1.1.0.1-A00
                        Release Date: 08/29/17
                        ===================================================================================================
                        New Features:
                        - None
                        Fixes:
                        - Fixed problem where Auto login caused a database access error