ibm_fw_uefi_yuooh1c-1.50_anyos_32-64: Version 1.50 - BuildID: YUOOH1C ------------------------------------------------- Version 1.50, YUOOH1C Problem(s) Fixed: - Update openssl to 1.0.2d. - Updated the firmware to address security vulnerabilities: CVE-2015-3200. - Disable CBC cipher and weak MAC algorithm for SSH in high security mode. Version 1.49, YUOOG9A Problem(s) Fixed: - Updated the firmware to address security vulnerabilities: CVE-2015-4000, CVE-2009-5146, CVE-2015-0209, CVE-2015-0286, CVE-2015-0287, CVE-2015-0288, CVE-2015-0289, CVE-2015-0292, CVE-2015-0293, CVE-2015-1788, CVE-2015-1789, CVE-2015-1790, CVE-2015-1791, CVE-2015-1792, CVE-2015-3216, - Enhance LDAP client security in high security mode of IMM. This is to remove the low security of cipher suite during the security LDAP communication. - Fix the IE8 compatiblity issue of IMM web (security page) interface for Customer. - Enhance logging for the case of losing configuration. Version 1.48, YUOOG8C Problem(s) Fixed: - Updated the firmware to address security vulnerabilities: CVE-2015-0204, CVE-2014-3570, CVE-2014-3572, CVE-2014-8275, CVE-2015-2808, CVE-2014-0191, CVE-2014-3660 - Fixed the issue where one invalid password entry for LDAP connection causes user lockout - Fixed the issue where password may become empty if it's updated by ASU tool through KCS interface. Version 1.47, YUOOG7C Problem Fixed: - Updated the firmware to address these vulnerabilities: CVE-2014-3566, CVE-2014-3568 - Fixed the problem that session cookie does not have the "HttpOnly" property Version 1.46, YUOOG7A Problem Fixed: - Enabled multicast filter to avoid IGMP flood on HS22, HS22V, HX5 Enhancements: - Updated the firmware to address these vulnerabilities: CVE-2013-2174, CVE-2014-0015, CVE-2014-0138,CVE-2014-0139 - Russia time zone update Version 1.45, YUOOG6D Problem Fixed: - - Fixed a problem on the x3550M3 where the IMM2 reports the SNMP engineID in ASCII instead of hexadecimal. Version 1.44, YUOOG6C Problem Fixed: - Critical Fix for x3550M3, x3650M3, dx360M3, x3630M3, x3400M3, x3620M3, x3500M3, x3200M3, x3250M3, dx360M2, x3550M2, x3650M2, x3400M2, x3500M2, x3850/x3950X5, x3690X5 -- Updated the firmware with patches to address the OpenSSL vulnerabilities listed in CVE-2014-0224, CVE-2014-0076 Enhancements: N/A Version 1.43, YUOOG6B Problem Fixed: - Fixed the problem that the LDAP group filter name changed after upgrading IMM. - Fixed the problem on blade servers where the management bus will become unstable if the AMM in slot1 is removed from chassis. - Fixed the problem that the SNMP engine ID is changed after IMM reset. Enhancements: - Add security enhancements. Version 1.42, YUOOG2C Problem Fixed: - Fixed a NTP sync problem on IMM web - Fixed a time zone setting problem on IMM web Enhancements: - Added SHA256 and SHA512 support - Add a message in IMM event logs when power on is blocked due to VRD issue on x3850 X5 - Power off the server after N boot attempts without locating a boot device on x3850 X5/x3950 X5/HX5. Version 1.41, YUOOF7C Problem Fixed: - Fixed the problem on blades where sometimes no throttle event was reported by AMM when CPU temperature is higher than Tcontrol. Enhancements: - Enhanced logging for throttle and Power Management. Version 1.40, YUOOF7A Problems Fixed: - Fixed the problem on x3690X5 that host OS will be shut down due to wrong overtemp event. - Fixed the problem that "unsupported software version" could be showed in event logs after updating IMM version 1.30 or newer on x3850/x3950 X5, x3690X5 and HX5 - Fixed the problem that SMTP user name field on IMM web page only allows 16 chars. - Fixed the problem on HS22 where IMM reports 0 watt power during initialization Enhancements: - Enabled IMM to fail over to backup automatically when there is a IMM firmware corruption - Enhanced IMM web GUI response. - Added notification when a corrupted GUID Partition Table (GPT) is encountered by UEFI during POST. Please refer to RETAIN Tip H207759 for details. - Enhanced logging for Power Controls management. Version 1.39, YUOOF2C Problems Fixed: - Fixed the problem on IBM System x3850X5 where SAP HANA configurations can reset in rare cases. More details in RETAIN Tip H207295. Version 1.38, YUOOF2B Problems Fixed: - Fixed the problem on x3850 X5/x3950 X5 where the System Fault LED will be lit when only one PSU is installed. Version 1.37, YUOOE9C Problems Fixed: - Corrected the voltage sensor threshold for HS22 and HS22V system. Version 1.36, YUOOF2A Enhancements: - Improved IMM web page Accessibility Version 1.35, YUOOE9B Problems Fixed: - Fixed the thermal issue for Broadcom quad port ethernet (IBM PN 49Y7948., FRU 49Y7949). - Fixed the problem that user authentication for LDAP with SSL will fail when Configured Credentials is enabled. - Updated the thermal profile for NVIDIA M2090 GPU card support in dx360 M3. - Fixed the problem on HS22 systems where pressing the KVM button too soon (right after Power LED starts blinking slowly) would make the KVM owner unable to be changed. - Fixed the problem on blade servers where IMM may report the "Unsupported blade/blower combination" error for 130W Westmere CPUs. - Fixed the problem on x3200 M3 where when power policy is set as "restore" or "always on" in uEFI, enforcing system shutdown during POST will cause automatic system boot-up. - Fixed the problem about SNMP drops intermittently and SNMP data cannot be accessed in a period of time - Fixed the problem on x3850 X5/x3950 X5 Multi-Node systems where "redundancy lost" event is not logged in the Primary Node when one of the power supplies in the Secondary Node is lost. - Optimized CPU power consumption calculation method for x3690 X5. - Fixed the problem on blade servers where IMM does not automatically recover NCSI. - Fixed the problem on blade servers that IMM constantly has "Init Failures" and fails to start up. - Fixed the Readme file problem that some IP addresses of LAN-over-USB instructions are inconsistent. - Fixed the CMOS Voltage Over Threshold problem on HS22V systems. - Fixed the problem that SSH login failed when the setting is configured as "Local first then Ldap" or ldap settings are not valid. - Fixed the problem that the IMM web interface responds too slowly or even fails to respond. Enhancements: - Enhanced the entropy (randomness) when generating SSL keys. - Added secure SMTP authentication support. - Added I/O board VPD information in IMM web interface - Added the function of letting Location LED remain on after system power-off. - Enhanced event Severity reporting of the QPI Link LED on x3850 X5/x3950 X5 so that IBM Director can interpret it correctly. - Improved IMM version reporting for IBM Director. - Added a function to keep 110V Power Supply Redundancy by throttling the system for x3850 X5/x3950 X5. - Usability enhancement: all events will be checked by default on the alert setting web page. - Enabled ASU to control each sub-category for email alert recipient setting and SNMP alerts setting. - Added new BCH Midplane (that supports 8Gbit Fibre Channel) support. - Added the function to capture all IMM logs with one button click. - Enhanced the DataPower appliance blade support. Version 1.34, YUOOE3E Enhancement: - Add support of the following fusion-io adapters : 1.2TB High IOPS MLC Adapter for IBM System x 2.4TB High IOPS MLC Adapter for IBM System x 365GB High IOPS MLC PCIe Adapter for IBM System x 785GB High IOPS MLC PCIe Adapter for IBM System x Version 1.33, YUOOE3C Problems Fixed: - Fixed the problem that a blade's Fault LED is showed as "on" on AMM GUI while there is no active critical event and the LED on the physical blade is off. - Fixed the problem that the "Date" header is missing from the IMM SMTP trap. - Fixed the problem that the "Look Below" LED (CR48) on x3690 X5 Memory Expansion Board may turn on incorrectly when there are no errors detected. - Fixed the problem on x3850 X5/x3950 X5 where the system information in the IMM configuration file may be truncated and the incomplete system information will cause the HTTP server in IMM run into an unstable state. - Fixed the problem that the Scalability LED turns off after the IMM on either node of a 2-Node x3850 X5/x3950 X5 is reset. - Fixed the problem that IMM on x3850 X5/x3950 X5 might fail to start after the IMM firmware is successfully upgraded. - Fixed the problem where "Comm Errors" may occur when the IMM firmware on HX5 is upgraded. - Fixed the problem that dx360 M3 may have PCI errors when a NVIDIA M2090 GPU card is installed. - Fixed the problem that opening the ActiveX remote console closes all open tabs in the same Internet Explorer window. - Fixed the problem that x3550 M3 may occur ServerRAID BBU over temperature and ServerRAID M5016 over heat issues. Enhancements: - Added Internet Explorer 9 support. - Changed the maximum User's Distinguished Name(DN) for LDAP from 128 bytes to 256 bytes. - Removed the limitation of 255 memberOf groups for an LDAP user in IMM. - Enhanced IMM Web session management. - Added an IMM command line (CLI) command for one time PXE boot option setting. - Added a new unique error code in AMM and changed the text in AMM and IMM for CMOS battery errors. - Updated Russia time zone definition to no more daylight saving time. Version 1.32, YUOOD4G Problems Fixed: - Fixed a problem where IMM web interface does not lock out a user if the same user exhausts login retries and gets locked out through the SSH interface - Fixed a problem that caused the IMM to report false critical DIMM temperature events - Fixed an intermittent problem where sometimes the Power Supply DC status LED is not illuminated on the x3550 M2/M3, x3650 M2/M3, x3620 M3 and x3630 M3 - Fixed a problem that sometimes causes the IMM web interface to shut down after multiple invalid login attempts Enhancements: - Added Service Advisor support on x3850/x3950 X5 and x3690 X5 - Changed the IMM firmware to allow every service port to be Enabled or Disabled - Changed the IMM firmware to not disable the network interface when there is a conflict IP address on the network - Changed the IMM firmware to permit SSL client certificates to be managed while the SSL client is enabled Version 1.31, YUOOC7F Problems Fixed: - Fixed the problem that after updating IMM firmware from versions prior to v1.10(YUOO57H) to v1.30(YUOOC7E) the system won't power on correctly -------------------------------------------------------------------------- ibm_fw_uefi_d6e162a-1.20_linux_32-64 IBM 7376/7377 (IBM system x 3620 M3/3630 M3 Server) uEFI Flash Update Version 1.20 (BuildID D6E162A) Change History Version 1.20 - BuildID: D6E162A - Suggested (Be aware to check the change history for any critical updates) Problem(s) Fixed: Enhancements: Limitations: Dependencies: -------------------------------------------------------------------------- ibm_fw_dsa_dsytc5f-9.53_linux_32-64 Version 9.53, Build ID DSYTC5F o New System Support: o New Operating System support: o New server options support: o Problem(s) Fixed: o Enhancement: o Limitations: Refer to readme o Functional change: o Dependencies: o Special usage: -------------------------------------------------------------------------- ibm_fw_sraidmr_1000-20.13.1-0245_linux_32-64 ServeRAID M1000 Series SAS/SATA Controller Firmware Update Adapters Supported: ServeRAID M1115 SAS/SATA Controller for IBM System X (81Y4448) ServeRAID M1015 SAS/SATA Controller (46M0831) Version 20.13.1-0245 - Moderate Impact/Low Probability of Occurrence --------------------- - Fixed an issue where virtual drivers become inconsistent after the system an AC failure. (SCGCQ00897229) - Fixed an issue where Illegal request sense messages are seen repeatedly in FW logs due to attempts to collect temperaure for pds which does not support page (0x2F) at every smart poll interval. (SCGCQ00898459) - Fixed an issue where command "cli set securitykey=Lsi@12345" fails with error code "1001" and error message "invalid key". - Added a warning message when preboot configuration utility is Disabled but the user tries to launch it. (SCGCQ00662761) - Fixed an issue where WebBIOS Advance software option menu from main page could hang the system. (SCGCQ00683327) - Updated the drive speed display string to support 12Gb/s (SCGCQ00751036) - Corrected inconsistency in size showing in for total capacity property between webBIOS and MSM (SCGCQ00752176) -------------------------------------------------------------------------- ibm_fw_mpt2sas_h1110-1.20.02_linux_32-64 BIOS/FW/UEFI Update for ServeRAID H1110 SAS/SATA Controller for IBM System x Controller Supported: ServeRAID H1110 SAS/SATA Controller for IBM System x (81Y4492) Version 1.20.02 ------------- Contains: BIOS Firmware UEFI Driver 7.39.00.00 20.00.05.00 7.27.04.00 - Fixed SMP passthrough command failure due to smp back off interrupt. Appears in system log as 0x311c0030. (SCGCQ00889925) - Fixed issue where host boot fails in the presence of blank flash/corrupt firmware in flash (SCGCQ00894439) - Fixed issue where SATA drive errors, bad performance, or boot failure may appear after update to 20.00.02.00 firmware (SCGCQ00859226)(Retain Tip# H015210) -------------------------------------------------------------------------- ibm_fw_hdd_sas-1.17.02_linux_32-64: Version 1.17.02 IBM SAS/SATA HDD/SSD Update Program Version 1.17.02 - Update Utility release for IBM x86 servers. Note: * - Fixed extremely low probable data compare error on I/O held in standby when followed by power cycle; extremely low probable data compare error due to nonvolatile cache(NVC) write data not getting written to disc. RETAIN TIP: H214784 - MIGR-5098277 Note: # - Fixed a block misalignment during a sequential read. RETAIN TIP: H214635 MIGR-5098037 This package acknowledges support of qualified devices and may include updates for drives with product ID strings of: SAS 3.5" - HUS724020ALS61, HUS724040ALS61 to N3L6 - internal updates. - ST1000NM0023, ST2000NM0023, ST3000NM0023, ST4000NM0023 to BC5H - See Note * above. - ST2000NM0054, ST4000NM0054, ST6000NM0054 to EC66 - see Note * above. - ST2000NM0043, ST4000NM0043 to EC5D - See Note * above. - Other drive codes are present for support identification. SAS 2.5" - WD3001BKHG-23D, WD6001BKHG-23D, WD9001BKHG-23D to ZA34 - follow-on release. - WD3002BKTG-23E, WD6002BKTG-23E, WD9002BKTG-23E to ZC33 - follow-on release. - HUC109030CSS60, HUC109060CSS60, HUC109090CSS60 to J2EH - follow-on release. - TXA2D20200GA6I, STXA2D20400GA6I, TXA2D20800GA6I, TXA2E21600GA6I to GB7P - enhancements. - ST300MM0006, ST600MM0006, ST900MM0006 to B56T - See Note * above. - ST300MM0026, ST600MM0026, ST900MM0026 to E56E - See Note * above. - ST2000NM0043, ST4000NM0043 to EC5D - See Note * above. - ST1200MM0007 to B57E - See Note * above. - ST1200MM0017 to E577 - See Note * above. - HUSMM1620ASS20, HUSMM1640ASS20, HUSMM1680ASS20, HUSMM1616ASS20 to J4C8 - See Note # above - HUSMM1620ASS20E, HUSMM1640ASS20E, HUSMM1680ASS20E, HUSMM1616ASS20E to N4C8 - See Note # above - Other drive codes are present for support identification. SATA 3.5" - MG04ACA200E, MG04ACA300E, MG04ACA400E, MG04ACA500E to SJ1D - performance inhancements. - ST1000NM0033, ST2000NM0033, ST3000NM0033, ST4000NM0033 to BB5C - See Note * above. - ST2000NM0024, ST4000NM0024, ST5000NM0024, ST6000NM0024 to BB65 - See Note * above. - WD2003FYYS-23W0B0 to WA36 - configuration additions. - WD2000FYYZ-23UL, WD3000FYYZ-23UL, WD4000FYYZ-23UL to WD39 - configuration additions. - HUA723030ALA6 to MKAOA930 - enhancements. - HUA723020ALA6 to MK7OA930 - enhancements. - Other drive codes are present for support identification. SATA 2.5" - MZ7GE240HMHP-000M3, MZ7GE480HMHP-000M3, MZ7GE960HMHP-000M3 to EXT0CA34 - ship level. - Other drive codes are present for support identification. SATA 1.8" - Drive codes are present for support identification.