Troubleshooting
Problem
Diagnostic error codes Refer to the following Diagnostic Error Codes when using the IBM PC Enhanced Diagnostics test. In the following index, X can represent any number.
Resolving The Problem
Diagnostic error codesRefer to the following Diagnostic Error Codes when using the IBM PC Enhanced Diagnostics test.
In the following index, X can represent any number.
| Diagnostic Error Code | FRU/Action |
| 000-000-XXX BIOS Test Passed |
1. No action |
| 000-002-XXX BIOS Timeout |
1. Flash the system 2. System board |
| 000-024-XXX BIOS Addressing test failure |
1. Flash the system 2. System board |
| 000-025-XXX BIOS Checksum Value error |
1. Flash the system 2. Boot block 3. System board |
| 000-026-XXX FLASH data error |
1. Flash the system 2. Boot block 3. System board |
| 000-027-XXX BIOS Configuration/Setup error |
1. Run Setup 2. Flash the system 3. Boot block 4. System board |
| 000-034-XXX BIOS Buffer Allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 000-035-XXX BIOS Reset Condition detected |
1. Flash the system 2. System board |
| 000-036-XXX BIOS Register error |
1. Flash the system 2. Boot block 3. System board |
| 000-038-XXX BIOS Extension failure |
1. Flash the system 2. Adapter card 3. System board |
| 000-039-XXX BIOS DMI data error |
1. Flash the system 2. System board |
| 000-195-XXX BIOS Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 000-196-XXX BIOS test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log. 2. Re-start the test to reset the log file. |
| 000-197-XXX BIOS test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 000-198-XXX BIOS test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 000-199-XXX BIOS test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 000-250-XXX BIOS APM failure |
1. Flash the system 2. System board |
| 000-270-XXX BIOS ACPI failure |
1. Flash the system 2. System board |
| 001-000-XXX System Test Passed |
1. No action |
| 001-00X-XXX System Error |
1. System board |
| 001-01X-XXX System Error |
1. System board |
| 001-024-XXX System Addressing test failure |
1. System board |
| 001-025-XXX System Checksum Value error |
1. Flash the system 2. System board |
| 001-026-XXX System FLASH data error |
1. Flash the system 2. System board |
| 001-027-XXX System Configuration/Setup error |
1. Run Setup 2. Flash the system 3. System board |
| 001-032-XXX System Device Controller failure |
1. System board |
| 001-034-XXX System Device Buffer Allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 001-035-XXX System Device Reset condition detected |
1. System board |
| 001-036-XXX System Register error |
1. System board |
| 001-038-XXX System Extension failure |
1. Adapter card 2. System board |
| 001-039-XXX System DMI data structure error |
1. Flash the system 2. System board |
| 001-040-XXX System IRQ failure |
1. Power-off/on system and re-test 2. System board |
| 001-041-XXX System DMA failure |
1. Power-off/on system and re-test 2. System board |
| 001-195-XXX System Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 001-196-XXX System test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log. 2. Re-start the test to reset the log file. |
| 001-197-XXX System test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 001-198-XXX System test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 001-199-XXX System test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 001-250-XXX System ECC error |
1. System board |
| 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error |
1. System board |
| 001-260-XXX 001-264-XXX System IRQ error |
1. System board |
| 001-268-XXX System IRQ1 failure |
1. Device on IRQ1 2. System board |
| 001-269-XXX System IRQ2 failure |
1. Device on IRQ2 2. System board |
| 001-270-XXX System IRQ3 failure |
1. Device on IRQ3 2. System board |
| 001-271-XXX System IRQ4 failure |
1. Device on IRQ4 2. System board |
| 001-272-XXX System IRQ5 failure |
1. Device on IRQ5 2. System board |
| 001-273-XXX System IRQ6 (diskette drive) failure |
1. Diskette Cable 2. Diskette drive 3. System board |
| 001-274-XXX System IRQ7 failure |
1. Device on IRQ7 2. System board |
| 001-275-XXX System IRQ8 failure |
1. Device on IRQ8 2. System board |
| Diagnostic Error Code | FRU/Action |
| 001-276-XXX System IRQ9 failure |
1. Device on IRQ9 2. System board |
| 001-277-XXX System IRQ10 failure |
1. Device on IRQ10 2. System board |
| 001-278-XXX System IRQ11 failure |
1. Device on IRQ11 2. System board |
| 001-279-XXX System IRQ12 failure |
1. Device on IRQ12 2. System board |
| 001-280-XXX System IRQ13 failure |
1. Device on IRQ13 2. System board |
| 001-281-XXX System IRQ14 (hard disk drive) failure |
1. Hard disk drive Cable 2. Hard disk drive 3. System board |
| 001-282-XXX System IRQ15 failure |
1. Device on IRQ15 2. System board |
| 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure |
1. System board |
| 001-292-XXX System CMOS RAM error |
1. Run Setup and re-test 2. System board |
| 001-293-XXX System CMOS Battery |
1. Battery 2. System board |
| 001-298-XXX System RTC date/time update failure |
1. Flash the system 2. System board |
| 001-299-XXX System RTC periodic interrupt failure |
1. System board |
| 001-300-XXX System RTC Alarm failure |
1. System board |
| 001-301-XXX System RTC Century byte error |
1. Flash the system 2. System board |
| 005-000-XXX Video Test Passed |
1. No action |
| 005-00X-XXX Video error |
1. Video card, if installed 2. System board |
| 005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX Video Signal failure |
1. Video card, if installed 2. System board |
| 005-016-XXX Video Simple Pattern test failure |
1. Video Ram 2. Video card, if installed 3. System board |
| 005-024-XXX Video Addressing test failure |
1. Video card, if installed 2. System board |
| 005-025-XXX Video Checksum Value error |
1. Video card, if installed 2. System board |
| 005-027-XXX Video Configuration/Setup error |
1. Run Setup 2. Video drivers update 3. Video card, if installed 4. System board |
| 005-031-XXX Video Device Cable failure |
1. Video cable 2. Monitor 3. Video card, if installed 4. System board |
| 005-032-XXX Video Device Controller failure |
1. Video card, if installed 2. System board |
| 005-036-XXX Video Register error |
1. Video card, if installed 2. System board |
| 005-038-XXX System BIOS extension failure |
1. Video card, if installed 2. System board |
| 005-040-XXX Video IRQ failure |
1. Video card, if installed 2. System board |
| 005-195-XXX Video Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 005-196-XXX Video test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 005-197-XXX Video test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 005-198-XXX Video test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 005-199-XXX Video test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 005-2XX-XXX 005-3XX-XXX Video subsystem error |
1. Video card, if installed 2. System board |
| 006-000-XXX Diskette interface Test Passed |
1. No action |
| 006-0XX-XXX Diskette interface error |
1. Diskette drive Cable 2. Diskette drive 3. System board |
| 006-195-XXX Diskette interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 006-196-XXX Diskette interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 006-197-XXX Diskette interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 006-198-XXX Diskette interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 006-199-XXX Diskette interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 006-25X-XXX Diskette interface Error |
1. Diskette drive cable 2. Diskette drive 3. System board |
| 011-000-XXX Serial port Interface Test Passed |
1. No action |
| 011-001-XXX Serial port presence |
1. Remove external serial device, if present 2. Run setup, enable port 3. System board |
| 011-002-XXX 011-003-XXX Serial port Timeout/Parity error |
1. System board |
| 011-013-XXX 011-014-XXX Serial port Control Signal/Loopback test failure |
1. System board |
| 011-015-XXX Serial port External Loopback failure |
1. Wrap plug 2. System board |
| 011-027-XXX Serial port Configuration/Setup error |
1. Run Setup, enable port 2. Flash the system 3. System board |
| 011-03X-XXX 011-04X-XXX Serial port failure |
1. System board |
| 011-195-XXX Serial port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 011-196-XXX Serial port test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 011-197-XXX Serial port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 011-198-XXX Serial port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined Problems |
| 011-199-XXX Serial port test failed, cause unknown |
1. Go to Undetermined Problems 2. Flash the system and re-test 3. Replace component under function test. |
| 011-2XX-XXX Serial port signal failure |
1. External serial device 2. System board |
| 014-000-XXX Parallel port Interface Test Passed |
1. No action |
| 014-001-XXX Parallel port Presence |
1. Remove external parallel device, if present 2. Run setup, enable port 3. System board |
| 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error |
1. System board |
| 014-013-XXX 014-014-XXX Parallel port Control Signal/Loopback test failure |
1. System board |
| 014-015-XXX Parallel port External Loopback failure |
1. Wrap plug 2. System board |
| 014-027-XXX Parallel port Configuration/Setup error |
1. Run Setup, enable port 2. Flash the system 3. System board |
| 014-03X-XXX 014-04X-XXX Parallel port failure |
1. System board |
| 014-195-XXX Parallel port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 014-196-XXX Parallel port test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 014-197-XXX Parallel port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 014-198-XXX Parallel port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 014-199-XXX Parallel port test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 014-2XX-XXX 014-3XX-XXX Parallel port failure |
1. External parallel device 2. System board |
| 015-000-XXX USB port Interface Test Passed |
1. No action |
| 015-001-XXX USB port presence |
1. Remove USB Device(s) and re-test 2. System board |
| 015-002-XXX USB port Timeout |
1. Remove USB Device(s) and re-test 2. System board |
| 015-015-XXX USB port External Loopback failure |
1. Remove USB Device(s) and re-test 2. System board |
| 015-027-XXX USB port Configuration/Setup error |
1. Flash the system 2. System board |
| 015-032-XXX USB port Device Controller failure |
1. System board |
| 015-034-XXX USB port buffer allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 015-035-XXX USB port Reset condition detected |
1. Remove USB Device(s) and re-test 2. System board |
| 015-036-XXX USB port Register error |
1. System board |
| 015-040-XXX USB port IRQ failure |
1. Run setup and check for conflicts 2. Flash the system 3. System board |
| 015-195-XXX USB port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 015-196-XXX USB port test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 015-197-XXX USB port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 015-198-XXX USB port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 015-199-XXX USB port test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 018-000-XXX PCI Card Test Passed |
1. No action |
| 018-0XX-XXX PCI Card Failure |
1. PCI card 2. Riser card, if installed 3. System board |
| 018-195-XXX PCI Card Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 018-196-XXX PCI Card test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 018-197-XXX PCI Card test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 018-198-XXX PCI Card test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 018-199-XXX PCI Card test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 018-250-XXX PCI Card Services error |
1. PCI card 2. Riser card, if installed 3. System board |
| 020-000-XXX PCI Interface Test Passed |
1. No action |
| 020-0XX-XXX PCI Interface error |
1. PCI card 2. Riser card, if installed 3. System board |
| 020-195-XXX PCI Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 020-196-XXX PCI test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 020-197-XXX PCI test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 020-198-XXX PCI test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 020-199-XXX PCI test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 020-262-XXX PCI system error |
1. PCI card 2. Riser card, if installed 3. System board |
| 025-000-XXX IDE interface Test Passed |
1. No action |
| 025-00X-XXX 025-01X-XXX IDE interface failure |
1. IDE signal cable 2. Check power supply 3. IDE device 4. System board |
| 025-027-XXX IDE interface Configuration/Setup error |
1. IDE signal cable 2. Flash the system 3. IDE device 4. System board |
| 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure |
1. IDE signal cable 2. Check power supply 3. IDE device 4. System board |
| 025-195-XXX IDE interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 025-196-XXX IDE interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 025-197-XXX IDE interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 025-198-XXX IDE interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 025-199-XXX IDE interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 030-000-XXX SCSI interface Test Passed |
1. No action |
| 030-00X-XXX 030-01X-XXX SCSI interface failure |
1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-027-XXX SCSI interface Configuration/Setup error |
1. SCSI signal cable 2. Flash the system 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-03X-XXX 030-04X-XXX SCSI interface error |
1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-195-XXX SCSI interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 030-196-XXX SCSI interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 030-197-XXX SCSI interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 030-198-XXX SCSI interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 030-199-XXX SCSI interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 035-000-XXX RAID interface Test Passed |
1. No action |
| 035-0XX-XXX RAID interface Failure |
1. RAID signal cable 2. RAID device 3. RAID adapter card, if installed 4. System board |
| 035-195-XXX RAID interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 035-196-XXX RAID interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 035-197-XXX RAID interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 035-198-XXX RAID interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 035-199-XXX RAID interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 071-000-XXX Audio port Interface Test Passed |
1. No action |
| 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error |
1. Run Setup 2. Flash the system 3. System board |
| 071-03X-XXX Audio port failure |
1. Speakers 2. Microphone 3. Audio card, if installed 4. System board |
| 071-04X-XXX Audio port failure |
1. Run Setup 2. Audio card, if installed 3. System board |
| 071-195-XXX Audio port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 071-196-XXX Audio port test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 071-197-XXX Audio port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 071-198-XXX Audio port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 071-199-XXX Audio port test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 071-25X-XXX Audio port failure |
1. Speakers 2. Audio card, if installed 3. System board |
| 080-000-XXX Game Port interface Test Passed |
1. No action |
| 080-XXX-XXX Game Port interface Error |
1. Remove the game port device and re-test the system |
| 080-195-XXX Game Port interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 080-196-XXX Game Port interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 080-197-XXX Game Port interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 080-198-XXX Game Port interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 080-199-XXX Game Port interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 086-000-XXX Mouse Port interface Test Passed |
1. No action |
| 086-001-XXX Mouse Port interface Presence |
1. Mouse 2. System board |
| 086-032-XXX Mouse Port interface Device controller failure |
1. Mouse 2. System board |
| 086-035-XXX Mouse Port interface Reset |
1. Mouse 2. System board |
| 086-040-XXX Mouse Port interface IRQ failure |
1. Run Setup 2. Mouse 3. System board |
| 086-195-XXX Mouse Port interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 086-196-XXX Mouse Port interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 086-197-XXX Mouse Port interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 086-198-XXX Mouse Port interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 086-199-XXX Mouse Port interface test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 089-000-XXX Microprocessor Test Passed |
1. No action |
| 089-XXX-XXX Microprocessor failure |
1. Microprocessor(s) 2. System board |
| 089-195-XXX Microprocessor Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 089-196-XXX Microprocessor test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 089-197-XXX Microprocessor test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 089-198-XXX Microprocessor test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 089-199-XXX Microprocessor test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 170-000-XXX Voltage Sensor(s) Test Passed |
1. No action |
| 170-0XX-XXX Voltage Sensor(s) failure |
1. Flash system 2. System board |
| 170-195-XXX Voltage Sensor(s) Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 170-197-XXX Voltage Sensor(s) test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 170-198-XXX Voltage Sensor(s) test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 170-199-XXX Voltage Sensor(s) test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error |
1. Power supply 2. System board |
| 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error |
1. System board 2. Microprocessor |
| 175-000-XXX Thermal Sensor(s) Test Passed |
1. No action |
| 175-0XX-XXX Thermal Sensor(s) failure |
1. Flash system 2. System board |
| 175-195-XXX Thermal Sensor(s) Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded |
1. Press F3 to review the log file. See Viewing the test log 2. Re-start the test to reset the log file. |
| 175-197-XXX Thermal Sensor(s) test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 175-198-XXX Thermal Sensor(s) test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to Undetermined problems |
| 175-199-XXX Thermal Sensor(s) test failed, cause unknown |
1. Go to Undetermined problems 2. Flash the system and re-test 3. Replace component under function test. |
| 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error |
1. Check fans 2. Check Power supply 3. Microprocessor 4. System board |
| 185-000-XXX Asset Security Test Passed |
1. No action |
| 185-XXX-XXX Asset Security failure |
1. Assure AssetSecurity Enabled 2. Flash system 3. System board |
| 185-278-XXX Asset Security Chassis Intrusion |
1. C2 Cover Switch 2. System board |
| 201-000-XXX System Memory Test Passed |
1. No action |
| 201-XXX-XXX System Memory error |
1. Replace the memory module called out by the test 2. System board |
| 202-000-XXX System Cache Test Passed |
1. No action |
| 202-XXX-XXX System Cache error |
1. Cache, if removable 2. System board 3. Microprocessor |
| 206-000-XXX Diskette Drive Test Passed |
1. No action |
| 206-XXX-XXX Diskette Drive error |
1. Diskette Drive Cable 2. Check power supply voltages 3. Diskette drive 4. System board |
| 215-000-XXX CD-ROM Drive Test Passed |
1. No action |
| 215-XXX-XXX CD-ROM Drive error |
1. CD-ROM Drive Cable 2. Check power supply voltages 3. CD-ROM drive 4. System board |
| 217-000-XXX Hard Disk Drive Test Passed |
1. No action |
| 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error |
1. Hard Disk Drive Cable 2. Check power supply voltages 3. Hard Disk drive (IDE) 4. System board |
| 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error |
1. Hard Disk Drive Cable 2. Check power supply voltages 3. Hard Disk drive (SCSI) 4. SCSI adapter card 5. System board |
| 220-000-XXX Hi-Capacity Cartridge Drive Test Passed |
1. No action |
| 220-XXX-XXX Hi-Capacity Cartridge Drive error |
1. Remove the Hi-Capacity Cartridge Drive and re-test the system |
| 301-000-XXX Keyboard Test Passed |
1. No action |
| 301-XXX-XXX Keyboard error |
1. Keyboard 2. Check and test Mouse 3. System board |
| 302-000-XXX Mouse Test Passed |
1. No action |
| 302-XXX-XXX Mouse error |
1. Mouse 2. Check and test Keyboard 3. System board |
| 303-000-XXX Joystick Test Passed |
1. No action |
| 303-XXX-XXX Joystick error |
1. Remove the Joystick and re-test the system |
| 305-000-XXX Monitor DDC Test Passed |
1. No action |
| 305-250-XXX Monitor DDC self test failure |
1. Run Setup to enable DDC 2. Cable 3. Monitor 4. Video card 5. System board |
| 415-000-XXX Modem Test Passed |
1. No action |
| 415-XXX-XXX Modem error |
1. Remove the Modem and re-test the system |
Document Location
Worldwide
[{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"QU02OWA","label":"Older System x->Netfinity 1000->8477"},"Platform":[{"code":"PF025","label":"Platform Independent"}],"Line of Business":{"code":"","label":""}}]
Was this topic helpful?
Document Information
Modified date:
28 January 2019
UID
ibm1MIGR-48WUP9