Installing VMware ESX Server 3.0 - IBM xSeries 346 (Type 8840, 1880)

Steps

Installation Instructions for VMware ESX Server 3.0 for IBM xSeries 346 (Type 8840, 1880)

1.0 What you will need

2.0 Where to download device drivers and files

3.0 Preparing the hardware

4.0 Detailed installation instructions

• 4.1 Installing VMware ESX Server 3.0
• 4.2 Installing the ASM driver

5.0 Notices

Revision Level: 1.00

Updated: 31 May 2007

(C) Copyright International Business Machines Corporation 2007. All rights reserved. US Government Users Restricted Rights - Use, duplication, or disclosure restricted by GSA ADP Schedule Contract with IBM Corp.

Note: Before using this information and the product it supports, read the general information in 5.0 Notices in this document.

Supported Server: IBM xSeries 346 Type 8840

Follow the instructions in this document in sequential order unless these instructions advise you otherwise. Windows and messages might differ from those in this document. Throughout this document, the term select is used to denote the use of arrow keys, the Tab key, Alt + a letter combination, or the mouse to make a selection.

References to optional hardware in this document do not imply support of that hardware. For information about supported options, see the ServerProven information for your blade server at http://www-03.ibm.com/servers/eserver/serverproven/compat/us/.

You must have the following software and hardware for the installation:

• A registered copy of VMware ESX Server 3.0.
• Supported hard disk drives. Go to http://www-03.ibm.com/servers/eserver/serverproven/compat/us/ for the ServerProven list of supported options and part numbers for the server.
• One blank diskette to create a BIOS code update diskette. You might need additional blank diskettes for firmware updates.
• If you are using the Adaptec HostRAID functionality, you need the IBM ServeRAID-7e (Adaptec HostRAID) Support CD.
• If you are using an IBM ServeRAID adapter, you need the IBM ServeRAID Support CD.

You can download device drivers and files from the following sites:

• VMware Web site: http://www.vmware.com
• IBM U.S. Support Web site: http://www.ibm.com/systems/support/
• IBM device driver download site: Software and device drivers
• For countries outside the U.S., start at http://www.ibm.com/

You can download product specifications from the following sites:

• For IBM System x product specifications, go tohttp://www.ibm.com/servers/eserver/education/cust/xseries/xref.html

To prepare the hardware, update system firmware, and configure arrays, refer to the Installation Guide located at the IBM Support Web site at http://www.ibm.com/systems/support/.

To install VMware ESX Sever 3.0, complete the following steps:

1. Insert the VMware ESX Server 3.0 operating system CD into the CD drive and boot the system.
2. Follow the detailed instructions from the Installation and Upgrade Guide located at http://www.vmware.com/pdf/vi3_30_20_installation_guide.pdf to install Vmware ESX Server 3.0.
3. Visit http://www.vmware.com/support/pubs/ for further information on installation and support of guest operating systems, and configuration and administration of VMware ESX 3.0.

Note: If a CD/RW drive is installed in your system, follow these steps before installing virtual machines:

1. Log on to the ESX server as root and make a copy of /boot/grub/grub.conf.
2. Edit grub.conf and look for "hda=ide-scsi" at the end of the kernel load image.
3. Remove "hda=ide-scsi".
4. Reboot the server.

To install the ASM driver, complete the following steps:

1. Insert the VMware ESX Server 3.0 operating system CD into the server and mount the drive.

   mount /mnt/cdrom
   

2. Go to the VMware/RPMS directory on the CD and install libusb-0.1.6-3.i386.rpm and libusb-devel-0.1.6-3.i386.rpm.

   rpm -ivh libusb-0.1.6-3.i386.rpm
   

   rpm - ivh libusb-devel-0.1.6.-3.i386.rpm
   

3. Download the ASM driver from http://www.ibm.com/systems/support/supportsite.wss/brandmain?brandind=5000008
   
   
4. If this is an upgrade to an existing Remote Supervisor Adapter II daemon, the previously installed Remote Superviser Adapter II daemon must be removed. Do not try to upgrade the rpm with the upgrade (-U) switch. To install the RPM execute the following commands:

   rpmbuild --rebuild ibmusbasm-1.XX.src.rpm
   

5. In order to make the RPM file, which builds and installs the Remote Supervisor Adapter II daemon and/or support software for the IBM Remote Supervisor Adapter II, run the following steps.

   cd /usr/src/redhat/RPMS/i386
   

   rpm -ivh ibmusbasm-1.XX.i386.rpm
   

INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS PUBLICATION "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some jurisdictions do not allow disclaimer of express or implied warranties in certain transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the publication. IBM may make improvements and/or changes in the product(s) and/or the program(s) described in this publication at any time without notice.

IBM, eServer, System x, e-business logo, ServerProven, and ServeRAID are trademarks of the International Business Machines Corporation in the United States, other countries, or both.

Other company, product, or service names may be trademarks or service marks of others.