Integrated Baseboard Management Controller (iBMC) - IBM System x3100 M3

Download Description

• New IBM xSeries firmware and device driver file naming convention
• Having trouble downloading a file from our site?

Change history

Version 0.13.0 - BuildID: J2BT13A

• Fixed : iBMC-System should be get MBE LOG in BIOS SEL when set erase MBE LOG in next
• reset Fixed : iBMC-Flash iBMC FW to factory configuration will cause E-mail alert function fail
  
• Fixed : iBMC-P3V3 AUX sensor UC voltage reading fail
  
• Fixed : iBMC-Cannot save the network configuration in WebGUI
  

Enhancements:
Limitations:
Dependencies:

Version 0.12.0 - BuildID: J2BT12A

• Fixed : EMET-No iBMC SEL while system occur memory Multi bit error
  
• Fixed : iBMC-WebGUI Virtual Media function failed
  
• Fixed : iBMC-Battery error LED light on when flash J2BT11A FW
  
• Fixed : iBMC-FW IOL power cycle drop too many KA packets
  
• Fixed : iBMC-Hard reset pef&snmp alert of Watchdog sensor cannot received in the destination

Enhancements:
Limitations:
Dependencies:

Version 0.11.0 - BuildID: J2BT11A

• Fixed : iBMC-DIMM Err Led cannot be lighted with OEM command
  
• Fixed : iBMC-When Remove the CPU Fan or System Fan, sometimes the Fan error LED can't be lighted
  
• Fixed : EMET-System Error LED will turn off when system reboot
  
• Fixed : iBMC-When Press the NMI button, the Front fault LED and sys board LED cannot be lighted Fixed : BIOS-System hang up when running AC power cycle
  
• Fixed : iBMC-iBMC generate a sel for P3V3 Aux automatically
  
• Fixed : iBMC-During the iBMC flashing,system halt
  

Enhancements:

• Support HTTP protocol to log Web GUI
  
• Support "no timeout" in Web GUI
  

Limitations:
Dependencies:

Version 0.10.0 - BuildID: J2BT10A
Problem(s) Fixed:

• Fixed : BIOS-System halt and buzzer will buzze when run warmboot or stress under SLES11 64bit Fixed : EMET-No iBMC SEL while system occur memory Multi bit error
  
• Fixed : EMET-No error message in BIOS event LOG while system occur memory multi-bit error
  
• Fixed : EMET-Motherboard all error LED can not be lighted at sometimes
  
• Fixed : EMET-When inject memroy SBE to system,The memory error LED can no be lighted at sometimes
  
• Fixed : iBMC-P1 temp status was unnormal in WebGUI
  

Enhancements:
Limitations:
Dependencies:

Version 0.9.0 - BuildID: J2BT09A
Problem(s) Fixed:

• Fixed : iBMC-FW flashed Fail because usb device detected timeout
  
• Fixed : iBMC-Flashing J2BT08A FW is failed
  
• Fixed : WHQL-"Signed Driver Check" VGA test failed caused by lack of SSID
  
• Fixed : iBMC-Check FW version in SMBridge is mismatch with WebGUI
  

Enhancements:
Limitations:
Dependencies:

Version 0.8.0 - BuildID: J2BT08A
Problem(s) Fixed:

• Fixed : WHQL-Dvd test failed
  
• Fixed : WHQL-Cdrom test failed
  
• Fixed : iBMC-Email alert has no function in webgui setup
  
• Fixed : EMET-IMM SEL show LOG message mismatch with BIOS SEL
  

Enhancements:
Limitations:
Dependencies:

Version 0.7.0 - BuildID: J2BT07A
Problem(s) Fixed:

• Fixed : iBMC-Trap settings are unreasonable
  
• Fixed : iBMC-Password of User id 2,3,4 can not set to null
  
• Fixed : iBMC-MP EMS virtual device is unstable showing in BIOS
  
• Fixed : iBMC-IPv6 address function fail under WebGUI
  
• Fixed : iBMC-Get system restart cause by PEF power cycle Fail
  
• Fixed : iBMC-Flash BMC firmware on linux platform,the shell script cannot be executed
  
• Fixed : iBMC-Establish iol connection fail with user id 1
  
• Fixed : iBMC-Error led did not keep lightting on when system restart
  
• Fixed : iBMC-BMC USERID 1 cannot be enabled
  
• Fixed : BIOS-System usually stay at LOGO screen, BIOS screen or POST screen about several secends
  

Enhancements:
Limitations:
Dependencies:

Version 0.6.0 - BuildID: J2BT06A
Problem(s) Fixed:

• Fixed : EMET-No error message in BIOS event LOG while system occur memory single or Multi bit error
  
• Fixed : EMET-No iBMC SEL while system occur memory Multi bit error
  
• Fixed : EMET-The Memory error LED no light while system occur memory single or Multi bit error
• Fixed : iBMC-BMC Alert Setting Consistence Fail
  

Enhancements:
Limitations:
Dependencies:

Version 0.5.0 - BuildID: J2BT05A
Problem(s) Fixed:

• Fixed : iBMC-Email alert has no function in webgui setup
  
• Fixed : iBMC-Current iBMC Firmware version mismatch with WebGUI
  
• Fixed : iBMC-Power LED status is fail
  
• Fixed : EMET-The PCIE slot error LED no light while system occur PCIE error
  
• Fixed : iBMC-No PEF relate sel logged when PEF trap trigger
  
• Fixed : iBMC-The power unit failure detected function of Sys Pwr Monitor sensor is fail
  
• Fixed : iBMC-The AC lost function of Sys Pwr Monitor sensor is fail
  
• Fixed : iBMC-Watchdog pre-timeout interrupt flag can not be get
  
• Fixed : iBMC-Chassis control/Soft-shutdown IPMI command not be supported
  
• Fixed : iBMC-Soft Reset can not be detected by IPMI command
  
• Fixed : iBMC-DC Off/On system via pushbutton can not be detect by IPMI command
  
• Fixed : iBMC-The response code format of set LED status command not match with spec
  
• Fixed : iBMC-Network speed and duplux mode are unusefull items under WebGUI
  

Enhancements:
Limitations:
Dependencies:

Version 0.4.0 - BuildID: J2BT04A
Problem(s) Fixed:

• Fixed : iBMC-iBMC WEBGUI has no VM and KVM function
  
• Fixed : iBMC-The SEL sequence of P1 Temp sensor is wrong
  
• Fixed : iBMC-P1 ProcHot sensor has no function
  
• Fixed : IFT-Linux-ASR function test failed in RHEL5.4 and SLES11
  
• Fixed : EMET-The System Error LED and Planner Fault LED have not Light while system occur error
• Fixed : iBMC-Can not Flash BMC Firmware under Windows platform (wflash)
  
• Fixed : iBMC-Can not Flash BMC Firmware under SLES XEN platform (lflash)
  
• Fixed : iBMC-Can not Flash BMC Firmware under SLES platform (lflash)
  
• Fixed : iBMC-Can not Flash BMC Firmware under RHEL platform (lflash)
  
• Fixed : iBMC-System error LED status is fail
  
• Fixed : iBMC-iBMC need long time to initialize at POST
  
• Fixed : iBMC-System fan LED function fail
  
• Fixed : iBMC-Planner fault LED function fail
  
• Fixed : iBMC-SNMP alert has no function in webgui setup
  
• F ixed : iBMC-P1 state sensor has no function
  
• Fixed : iBMC-HDD fan LED function fail
  
• Fixed : iBMC-CPU Fault LED function fail
  
• Fixed : iBMC-CPU Fan LED function fail
• Fixed : iBMC-System auto generates two SLP Status system envent logs
  Fixed : iBMC-SEL State sensor has no function
• Fixed : iBMC-SEL Full Rate sensor cannot trigger a upper non-recoverable event
  
• Fixed : iBMC-System auto generates two P1 Temp system envent logs
  
• Fixed : iBMC-P1 VRD sensor has no function
  
• Fixed : iBMC-Can not connect to iBMC via serial port
  
• Fixed : iBMC-SMI sensor has no function
  
• Fixed : iBMC-Number of event filter table entries mismatch with iBMC spec
  
• Fixed : iBMC-Get LED status command fail and the response code format not comply with spec describe
  

Enhancements:
Limitations:
Dependencies:

Version 0.3.0 - BuildID: J2BT03A
Problem(s) Fixed:

• Fixed : CPU FAN always in full speed
  
• Fixed : Get sensor event enable error on Fans sensor
  
• Fixed : Get sensor reading error on Fans sensor
  
• Fixed : Get sensor reading error on sensor P1 CATERR
  
• Fixed : Get sensor threshold error on Fans sensor
  
• Fixed : HDD FAN always in full speed
  
• Fixed : iBMC_DIMMM argin Sensor Function Fail
  
• Fixed : System FAN always in full speed
  

Enhancements:
Limitations:

Version 0.2.0 - BuildID: J2BT02A
Problem(s) Fixed:

• Fixed : iBMC-iBMC have no SDR
  
• Fixed : iBMC-iBMC selftest fail
  

Enhancements:
Limitations:

Version 0.1.0 - BuildID: J2BT01A

• Initial release