HD83774: PART:MULTI-SECTION SOLID GIVES ERROR MESSAGE FOR DIFFERENT CLOS ING POINTS IN SPECIAL CASE

APAR status

• Closed as program error.

Error description

• PART:Multi-Section Solid gives error message for
  different closing points in special case.
  .
  SCENARIO:
  0. Start V5- Workbench: Part Design
  1. Open the supplied CATPart
  2. Select the command: Multi-section Solid
  3. Select Sketch1 in the tree
  4. Select Sketch2 in the tree
  5. Mark the line 1 with sketch1 in the menu and use
  the right mouse button with Replace closing point
  and select Point1_1_2
  6. Mark the line 2 with sketch2 in the menu and use
  the right mouse button with Replace closing point
  and select Point2_1
  7. Switch to Coupling and select the Sections
  coupling:Vertices
  8. Push the Add button and then select in the tree
  Point1_1_2 and Point2_1, Point1_1_2 and Point2_2
  Point1_3_4 and Point2_3,Point1_3_4 and Point2_4
  9. Use Preview
  An error is thrown Multi-Sections Solid.1 - Loft
  operator:
  Impossible to homogenize the sections before the
  loft computation
  For detail scenario please refer the avi file
  attached.
  .
  RESULT:
  An error is thrown Multi-Sections Solid.1 - Loft
  operator:
  Impossible to homogenize the sections before the
  loft computation.
  Solid is not created
  .
  .
  

Local fix

Problem summary

• PART:Multi-Section Solid gives error message for different clos
  ing points in special case
  PART:Multi-Section Solid gives error message for
  different closing points in special case.
  .
  SCENARIO:
  0. Start V5- Workbench: Part Design
  1. Open the supplied CATPart
  2. Select the command: Multi-section Solid
  3. Select Sketch1 in the tree
  4. Select Sketch2 in the tree
  5. Mark the line 1 with sketch1 in the menu and use
  the right mouse button with Replace closing point
  and select Point1_1_2
  6. Mark the line 2 with sketch2 in the menu and use
  the right mouse button with Replace closing point
  and select Point2_1
  7. Switch to Coupling and select the Sections
  coupling:Vertices
  8. Push the Add button and then select in the tree
  Point1_1_2 and Point2_1, Point1_1_2 and Point2_2
  Point1_3_4 and Point2_3,Point1_3_4 and Point2_4
  9. Use Preview
  An error is thrown Multi-Sections Solid.1 - Loft
  operator:
  Impossible to homogenize the sections before the
  loft computation
  For detail scenario please refer the avi file
  attached.
  .
  RESULT:
  An error is thrown Multi-Sections Solid.1 - Loft
  operator:
  Impossible to homogenize the sections before the
  loft computation.
  Solid is not created
  .
  .
  

Problem conclusion

• THIS PROBLEM WILL BE FIXED ON CATIA VERSION
  5 RELEASE R19 SP05 AND R20 GA LEVEL.
  Incident Diagnosis:
  Sections homogenization fails in particular case of
  coupling lines intersecting one another on section
  closure point
  .
  Correction Explanation:
  There was a confusion with closure point for the
  intersection point of coupling guide/section.This
  behavior has been corrected.
  .
  

Temporary fix

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

Fix information

• Fixed component name

  CATIA V5 NT>XP

• Fixed component ID

  569151000

Applicable component levels

• R519 PSN

     UP