HD98612: Measure Does Not Update When Accessed Through Catalog

APAR status

• Closed as program error.

Error description

• ABSTRACT:
  Measure does not get updated when accessed through Catalog.
  .
  SCENARIO:
  1. Start CATIA V5R19SP5 and go to Tools/Options/Parameters and M
  easure/Measure Tools tab and enable "Automatic update in part".
  2. Open "SamplePart.CATPart" that has the following characterist
  ics:
   a. One PartBody composed of a single Pad
   b. Assigned material Aluminum
   c. Inertia Measure named InertiaVolume.1
   d. Parameter Mass.1 that reports mass volume from InertiaVolume
  .1
   e. Parameter PartLength corresponding to a dimension on the pad
  
   f. Parameter PartNumber
   g. Design table with 5 configurations. Two columns: PartNumber,
   Length (Reference SamplePartDT.xls)
  3. Note the mass value under InertiaVolume.1.
  3. Create new Catalog Document.
  4. Click ???Add Part Family??? and click ???Select Part Document
  ???. Select SamplePart.CATPart file. Click OK.
  5. In catalog document, Right click on any configuration and sel
  ect "Open New Document". A new document is created and opened.
  6. Note the mass value under InertiaVolume.1.
  The reported mass in the measurement InertiaVolume.1 is 0lb. Con
  sequently the Mass.1 parameter displays 0lb. The measurement can
  not be updated. Editing the InertiaVolume.1 measure indicates th
  at there is no selection. An accurate, updated value is expected
  .
  .
  RESULT:
  The reported mass in the measurement InertiaVolume.1 is "0". The
   Mass value is not updated when it is accessed through Catalog.
  .
  EXPECTED RESULT:
  The Mass value should be accurate & updated when it is accessed
  through Catalog.
  

Local fix

• empty
  

Problem summary

• ABSTRACT:
  Measure does not get updated when accessed through Catalog.
  .
  SCENARIO:
  1. Start CATIA V5R19SP5 and go to Tools/Options/Parameters
  and Measure/Measure Tools tab and enable "Automatic update in
  part".
  2. Open "SamplePart.CATPart" that has the following
  characteristics:
   a. One PartBody composed of a single Pad
   b. Assigned material Aluminum
   c. Inertia Measure named InertiaVolume.1
   d. Parameter Mass.1 that reports mass volume from
  InertiaVolume.1
   e. Parameter PartLength corresponding to a dimension on the
  pad
   f. Parameter PartNumber
   g. Design table with 5 configurations. Two columns:
  PartNumber, Length (Reference SamplePartDT.xls)
  3. Note the mass value under InertiaVolume.1.
  3. Create new Catalog Document.
  4. Click ???Add Part Family??? and click ???Select Part Document
  ???.
  Select SamplePart.CATPart file. Click OK.
  5. In catalog document, Right click on any configuration and
  select "Open New Document". A new document is created and
  opened.
  6. Note the mass value under InertiaVolume.1.
  The reported mass in the measurement InertiaVolume.1 is 0lb.
  Consequently the Mass.1 parameter displays 0lb. The
  measurement cannot be updated. Editing the InertiaVolume.1
  measure indicates that there is no selection. An accurate,
  updated value is expected.
  .
  RESULT:
  The reported mass in the measurement InertiaVolume.1 is "0".
  The Mass value is not updated when it is accessed through
  Catalog.
  .
  EXPECTED RESULT:
  The Mass value should be accurate & updated when it is
  accessed through Catalog.
  

Problem conclusion

• THIS PROBLEM WILL BE FIXED ON CATIA VERSION V5R21 GA level.
  NOTE THAT THIS PROBLEM WILL ALSO BE FIXED ON V5R20 SP5.
  Additional Closure Information:
  Incident Diagnosis
  Measure Does Not Update When Avccessed Through Catalog.
  Correction Explanation
  There was a problem with building the Rep which was causing
  the issue. This problem is now corrected.
  

Temporary fix

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

Fix information

• Fixed component name

  CATIA V5 NT>XP

• Fixed component ID

  569151000

Applicable component levels

• R521 PSN

     UP