II08399: CBDG065I MSGCBDG065I CBDG060I MSGCBDG060I CBDG149I MSGCBDG149I RECEIVED AFTER DEFINING A SWITCH SWCH 9032 VIA HCD

APAR status

• Closed as canceled.

Error description

• PROBLEM 1:
  After defining a switch to HCD error msg's may
  be received when creating a production IODF.  The procedure to
  correct the error situations are as follows:
  1)  CBDG065I MSGCBDG065I The switch control unit XXX of switch
      yy has no channel path attached via the switch.
   a) Using HCD on the Define Channel Path panel specify a
      dynamic switch, entry switch and port.  On this panel the
      port specification refers to the entry port.
  
                        Dyn +  --Entry +--
  / CHPID Type + Mode + Switch Switch Port Con.
  _ 20    CNC    DED    01     01     C2
  .
    2) CBDG060I A switch and port must be specified for control
       unit xxxx to connect the control unit to channel path yy
       of processor bbbbb.
  
  
  a) In this case the switch and port information must be
     filled in using the Change Control Unit Definition Panel.
     Action code 'c' on the Control Unit List panel will take
     you to the Change Control Unit Definition panel.
  Connected to switches  . . . 01  __  __  __  __  __  __  __  +
  Ports  . . . . . . . . . . . D7  __  __  __  __  __  __  __  +
  .
   In this case the Port specification is the port to which the
  control unit will be attached.
  .
  ****************************************************************
  * For a more detailed description see the HCD and Dynamic I/O  *
  * Reconfiguration Primer Chapter 5 (GG24-4037)                 *
  ****************************************************************
  PROBLEM 2:
  CBDA260I Device type 9032 not supported by os type MVS.
  MSGCBDG154I CBDG154I No switch information is available
  MSGCBDG150I CBDG150I No Switch Information Table (SIT)
                       found for switch type
  The above messages are received when trying to define a
  d/t9033 or d/t9032 in HCD.
  Customers need to have FMID HSWF100 installed. This is
  the FMID for ESCON Director Device Support. For a 9033
  model 3 (9033-3) OW08540 is required. This FMID is orderable
  as a feature of MVS. The Feature number is 5872.
  Note:  In order to use the 9032 or 9033 it is not necessary
         to define the switch CU and IODEVICE in your IODF.
         Thus if the Escon Director Device support FMID is
         not installed devices that are attached to an
         ESCON director will be accessable via MVS even if
         the switch CU and IODEVICE are not defined at that
         time.  However, the CHPID and Control Unit's must
         be modified in the IODF to include switch number and
         link address.  Once the switch is defined in the IODF
         additional error reporting and validation will be
         available. See HCD Primer for additional information.
  
  PROBLEM3: CBDG149I-port range for installed ports outside
  range of supported ports. Error received when user tries to
  set the installed port range from C0-FB to 80-FB. UW21164
  will add new port ranges. The user must be sure to select
  the correct switch type.
  

Local fix

Problem summary

Problem conclusion

Temporary fix

Comments

• Info. apar.
  

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

Fix information

Applicable component levels