Troubleshooting
Problem
Refer to the following Diagnostic Error Codes when using the IBM PC Enhanced Diagnostics test.
Resolving The Problem
Diagnostic Error Codes
Refer to the following Diagnostic Error Codes when using the IBM PC Enhanced Diagnostics test.
In the following index, X can represent any number.
| Diagnostic Error Code | FRU/Action |
| 000-000-XXX BIOS Test Passed |
1. No action |
| 000-002-XXX BIOS Timeout |
1. Flash the system 2. System board |
| 000-024-XXX BIOS Addressing test failure |
1. Flash the system 2. System board |
| 000-025-XXX BIOS Checksum Value error |
1. Flash the system 2. Boot block 3. System board |
| 000-026-XXX FLASH data error |
1. Flash the system 2. Boot block 3. System board |
| 000-027-XXX BIOS Configuration/Setup error |
1. Run Setup 2. Flash the system 3. Boot block 4. System board |
| 000-034-XXX BIOS Buffer Allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 000-035-XXX BIOS Reset Condition detected |
1. Flash the system 2. System board |
| 000-036-XXX BIOS Register error |
1. Flash the system 2. Boot block 3. System board |
| 000-038-XXX BIOS Extension failure |
1. Flash the system 2. Adapter card 3. System board |
| 000-039-XXX BIOS DMI data error |
1. Flash the system 2. System board |
| 000-195-XXX BIOS Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 000-196-XXX BIOS test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log". 2. Re-start the test to reset the log file. |
| 000-197-XXX BIOS test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 000-198-XXX BIOS test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 000-199-XXX BIOS test failed, cause unknown |
1. Go to "Undetermined Problems". 2. Flash the system and re-test 3. Replace component under function test. |
| 000-250-XXX BIOS APM failure |
1. Flash the system 2. System board |
| 000-270-XXX BIOS ACPI failure |
1. Flash the system 2. System board |
| 001-000-XXX System Test Passed |
1. No action |
| 001-00X-XXX System Error |
1. System board |
| 001-01X-XXX System Error |
1. System board |
| 001-024-XXX System Addressing test failure |
1. System board |
| 001-025-XXX System Checksum Value error |
1. Flash the system 2. System board |
| 001-026-XXX System FLASH data error |
1. Flash the system 2. System board |
| 001-027-XXX System Configuration/Setup error |
1. Run Setup 2. Flash the system 3. System board |
| 001-032-XXX System Device Controller failure |
1. System board |
| 001-034-XXX System Device Buffer Allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 001-035-XXX System Device Reset condition detected |
1. System board |
| 001-036-XXX System Register error |
1. System board |
| 001-038-XXX System Extension failure |
1. Adapter card 2. System board |
| 001-039-XXX System DMI data structure error |
1. Flash the system 2. System board |
| 001-040-XXX System IRQ failure |
1. Power-off/on system and re-test 2. System board |
| 001-041-XXX System DMA failure |
1. Power-off/on system and re-test 2. System board |
| 001-195-XXX System Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 001-196-XXX System test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 001-197-XXX System test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 001-198-XXX System test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 001-199-XXX System test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 001-250-XXX System ECC error |
1. System board |
| 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error |
1. System board |
| 001-260-XXX 001-264-XXX System IRQ error |
1. System board |
| 001-268-XXX System IRQ1 failure |
1. Device on IRQ1 2. System board |
| 001-269-XXX System IRQ2 failure |
1. Device on IRQ2 2. System board |
| 001-270-XXX System IRQ3 failure |
1. Device on IRQ3 2. System board |
| 001-271-XXX System IRQ4 failure |
1. Device on IRQ4 2. System board |
| 001-272-XXX System IRQ5 failure |
1. Device on IRQ5 2. System board |
| 001-273-XXX System IRQ6 (diskette drive) failure |
1. Diskette Cable 2. Diskette drive 3. System board |
| 001-274-XXX System IRQ7 failure |
1. Device on IRQ7 2. System board |
| 001-275-XXX System IRQ8 failure |
1. Device on IRQ8 2. System board |
| 001-276-XXX System IRQ9 failure |
1. Device on IRQ9 2. System board |
| 001-277-XXX System IRQ10 failure |
1. Device on IRQ10 2. System board |
| 001-278-XXX System IRQ11 failure |
1. Device on IRQ11 2. System board |
| 001-279-XXX System IRQ12 failure |
1. Device on IRQ12 2. System board |
| 001-280-XXX System IRQ13 failure |
1. Device on IRQ13 2. System board |
| 001-281-XXX System IRQ14 (hard disk drive) failure |
1. Hard disk drive Cable 2. Hard disk drive 3. System board |
| 001-282-XXX System IRQ15 failure |
1. Device on IRQ15 2. System board |
| 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure |
1. System board |
| 001-292-XXX System CMOS RAM error |
1. Run Setup and re-test 2. System board |
| 001-293-XXX System CMOS Battery |
1. Battery 2. System board |
| 001-298-XXX System RTC date/time update failure |
1. Flash the system 2. System board |
| 001-299-XXX System RTC periodic interrupt failure |
1. System board |
| 001-300-XXX System RTC Alarm failure |
1. System board |
| 001-301-XXX System RTC Century byte error |
1. Flash the system 2. System board |
| 005-000-XXX Video Test Passed |
1. No action |
| 005-00X-XXX Video error |
1. Video card, if installed 2. System board |
| 005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX Video Signal failure |
1. Video card, if installed 2. System board |
| 005-016-XXX Video Simple Pattern test failure |
1. Video Ram 2. Video card, if installed 3. System board |
| 005-024-XXX Video Addressing test failure |
1. Video card, if installed 2. System board |
| 005-025-XXX Video Checksum Value error |
1. Video card, if installed 2. System board |
| 005-027-XXX Video Configuration/Setup error |
1. Run Setup 2. Video drivers update 3. Video card, if installed 4. System board |
| 005-031-XXX Video Device Cable failure |
1. Video cable 2. Monitor 3. Video card, if installed 4. System board |
| 005-032-XXX Video Device Controller failure |
1. Video card, if installed 2. System board |
| 005-036-XXX Video Register error |
1. Video card, if installed 2. System board |
| 005-038-XXX System BIOS extension failure |
1. Video card, if installed 2. System board |
| 005-040-XXX Video IRQ failure |
1. Video card, if installed 2. System board |
| 005-195-XXX Video Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 005-196-XXX Video test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 005-197-XXX Video test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 005-198-XXX Video test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 005-199-XXX Video test failed, cause unknown |
1. Go to "Undetermined Problems". 2. Flash the system and re-test 3. Replace component under function test. |
| 005-2XX-XXX 005-3XX-XXX Video subsystem error |
1. Video card, if installed 2. System board |
| 006-000-XXX Diskette interface Test Passed |
1. No action |
| 006-0XX-XXX Diskette interface error |
1. Diskette drive Cable 2. Diskette drive 3. System board |
| 006-195-XXX Diskette interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 006-196-XXX Diskette interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 006-197-XXX Diskette interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 006-198-XXX Diskette interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 006-199-XXX Diskette interface test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 006-25X-XXX Diskette interface Error |
1. Diskette drive Cable 2. Diskette drive 3. System board |
| 011-000-XXX Serial port Interface Test Passed |
1. No action |
| 011-001-XXX Serial port Presence |
1. Remove external serial device, if present 2. Run setup, enable port 3. System board |
| 011-002-XXX 011-003-XXX Serial port Timeout/Parity error |
1. System board |
| 011-013-XXX 011-014-XXX Serial port Control Signal/Loopback test failure |
1. System board |
| 011-015-XXX Serial port External Loopback failure |
1. Wrap plug 2. System board |
| 011-027-XXX Serial port Configuration/Setup error |
1. Run Setup, enable port 2. Flash the system 3. System board |
| 011-03X-XXX 011-04X-XXX Serial port failure |
1. System board |
| 011-195-XXX Serial port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 011-196-XXX Serial port test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 011-197-XXX Serial port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 011-198-XXX Serial port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 011-199-XXX Serial port test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 011-2XX-XXX Serial port signal failure |
1. External serial device 2. System board |
| 014-000-XXX Parallel port Interface Test Passed |
1. No action |
| 014-001-XXX Parallel port Presence |
1. Remove external parallel device, if present 2. Run setup, enable port 3. System board |
| 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error |
1. System board |
| 014-013-XXX 014-014-XXX Parallel port Control Signal/Loopback test failure |
1. System board |
| 014-015-XXX Parallel port External Loopback failure |
1. Wrap plug 2. System board |
| 014-027-XXX Parallel port Configuration/Setup error |
1. Run Setup, enable port 2. Flash the system 3. System board |
| 014-03X-XXX 014-04X-XXX Parallel port failure |
1. System board |
| 014-195-XXX Parallel port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 014-196-XXX Parallel port test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 014-197-XXX Parallel port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 014-198-XXX Parallel port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 014-199-XXX Parallel port test failed, cause unknown |
1. Go to "Undetermined Problems". 2. Flash the system and re-test 3. Replace component under function test. |
| 014-2XX-XXX 014-3XX-XXX Parallel port failure |
1. External parallel device 2. System board |
| 015-000-XXX USB port Interface Test Passed |
1. No action |
| 015-001-XXX USB port Presence |
1. Remove USB Device(s) and re-test 2. System board |
| 015-002-XXX USB port Timeout |
1. Remove USB Device(s) and re-test 2. System board |
| 015-015-XXX USB port External Loopback failure |
1. Remove USB Device(s) and re-test 2. System board |
| 015-027-XXX USB port Configuration/Setup error |
1. Flash the system 2. System board |
| 015-032-XXX USB port Device Controller failure |
1. System board |
| 015-034-XXX USB port buffer allocation failure |
1. Reboot the system 2. Flash the system 3. Run memory test 4. System board |
| 015-035-XXX USB port Reset condition detected |
1. Remove USB Device(s) and re-test 2. System board |
| 015-036-XXX USB port Register error |
1. System board |
| 015-040-XXX USB port IRQ failure |
1. Run setup and check for conflicts 2. Flash the system 3. System board |
| 015-195-XXX USB port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 015-196-XXX USB port test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 015-197-XXX USB port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 015-198-XXX USB port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 015-199-XXX USB port test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 018-000-XXX PCI Card Test Passed |
1. No action |
| 018-0XX-XXX PCI Card Failure |
1. PCI card 2. Riser card, if installed 3. System board |
| 018-195-XXX PCI Card Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 018-196-XXX PCI Card test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 018-197-XXX PCI Card test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 018-198-XXX PCI Card test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 018-199-XXX PCI Card test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 018-250-XXX PCI Card Services error |
1. PCI card 2. Riser card, if installed 3. System board |
| 020-000-XXX PCI Interface Test Passed |
1. No action |
| 020-0XX-XXX PCI Interface error |
1. PCI card 2. Riser card, if installed 3. System board |
| 020-195-XXX PCI Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 020-196-XXX PCI test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 020-197-XXX PCI test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 020-198-XXX PCI test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 020-199-XXX PCI test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 020-262-XXX PCI system error |
1. PCI card 2. Riser card, if installed 3. System board |
| 025-000-XXX IDE interface Test Passed |
1. No action |
| 025-00X-XXX 025-01X-XXX IDE interface failure |
1. IDE signal cable 2. Check power supply 3. IDE device 4. System board |
| 025-027-XXX IDE interface Configuration/Setup error |
1. IDE signal cable 2. Flash the system 3. IDE device 4. System board |
| 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure |
1. IDE signal cable 2. Check power supply 3. IDE device 4. System board |
| 025-195-XXX IDE interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 025-196-XXX IDE interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log on page 14. 2. Re-start the test to reset the log file. |
| 025-197-XXX IDE interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 025-198-XXX IDE interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 025-199-XXX IDE interface test failed, cause unknown |
1. Go to "Undetermined Problems". 2. Flash the system and re-test 3. Replace component under function test. |
| 030-000-XXX SCSI interface Test Passed |
1. No action |
| 030-00X-XXX 030-01X-XXX SCSI interface failure |
1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-027-XXX SCSI interface Configuration/Setup error |
1. SCSI signal cable 2. Flash the system 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-03X-XXX 030-04X-XXX SCSI interface error |
1. SCSI signal cable 2. Check power supply 3. SCSI device 4. SCSI adapter card, if installed 5. System board |
| 030-195-XXX SCSI interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 030-196-XXX SCSI interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log". 2. Re-start the test to reset the log file. |
| 030-197-XXX SCSI interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 030-198-XXX SCSI interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 030-199-XXX SCSI interface test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 035-000-XXX RAID interface Test Passed |
1. No action |
| 035-0XX-XXX RAID interface Failure |
1. RAID signal cable 2. RAID device 3. RAID adapter card, if installed 4. System board |
| 035-195-XXX RAID interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 035-196-XXX RAID interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 035-197-XXX RAID interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 035-198-XXX RAID interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 035-199-XXX RAID interface test failed, cause unknown |
1. Go to Undetermined Problems 2. Flash the system and re-test 3. Replace component under function test. |
| 071-000-XXX Audio port Interface Test Passed |
1. No action |
| 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error |
1. Run Setup 2. Flash the system 3. System board |
| 071-03X-XXX Audio port failure |
1. Speakers 2. Microphone 3. Audio card, if installed 4. System board |
| 071-04X-XXX Audio port failure |
1. Run Setup 2. Audio card, if installed 3. System board |
| 071-195-XXX Audio port Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 071-196-XXX Audio port test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 071-197-XXX Audio port test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 071-198-XXX Audio port test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 071-199-XXX Audio port test failed, cause unknown |
1. Go to Undetermined Problems 2. Flash the system and re-test 3. Replace component under function test. |
| 071-25X-XXX Audio port failure |
1. Speakers 2. Audio card, if installed 3. System board |
| 080-000-XXX Game Port interface Test Passed |
1. No action |
| 080-XXX-XXX Game Port interface Error |
1. Remove the game port device and re-test the system |
| 080-195-XXX Game Port interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 080-196-XXX Game Port interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log". 2. Re-start the test to reset the log file. |
| 080-197-XXX Game Port interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 080-198-XXX Game Port interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 080-199-XXX Game Port interface test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 086-000-XXX Mouse Port interface Test Passed |
1. No action |
| 086-001-XXX Mouse Port interface Presence |
1. Mouse 2. System board |
| 086-032-XXX Mouse Port interface Device controller failure |
1. Mouse 2. System board |
| 086-035-XXX Mouse Port interface Reset |
1. Mouse 2. System board |
| 086-040-XXX Mouse Port interface IRQ failure |
1. Run Setup 2. Mouse 3. System board |
| 086-195-XXX Mouse Port interface Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 086-196-XXX Mouse Port interface test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log". 2. Re-start the test to reset the log file. |
| 086-197-XXX Mouse Port interface test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 086-198-XXX Mouse Port interface test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems". |
| 086-199-XXX Mouse Port interface test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 089-000-XXX Microprocessor Test Passed |
1. No action |
| 089-XXX-XXX Microprocessor failure |
1. Microprocessor(s) 2. System board |
| 089-195-XXX Microprocessor Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 089-196-XXX Microprocessor test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log". 2. Re-start the test to reset the log file. |
| 089-197-XXX Microprocessor test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 089-198-XXX Microprocessor test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 089-199-XXX Microprocessor test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 170-000-XXX Voltage Sensor(s) Test Passed |
1. No action |
| 170-0XX-XXX Voltage Sensor(s) failure |
1. Flash system 2. System board |
| 170-195-XXX Voltage Sensor(s) Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 170-197-XXX Voltage Sensor(s) test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 170-198-XXX Voltage Sensor(s) test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 170-199-XXX Voltage Sensor(s) test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error |
1. Power supply 2. System board |
| 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error |
1. Voltage Regulator Module (VRM) 2. Microprocessor 3. System board |
| 175-000-XXX Thermal Sensor(s) Test Passed |
1. No action |
| 175-0XX-XXX Thermal Sensor(s) failure |
1. Flash system 2. System board |
| 175-195-XXX Thermal Sensor(s) Test aborted by user |
1. Information 2. Re-start the test, if need to |
| 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded |
1. Press F3 to review the log file. See "Viewing the Test Log" 2. Re-start the test to reset the log file. |
| 175-197-XXX Thermal Sensor(s) test warning |
1. Make sure component that is called out is enabled and/or connected 2. Re-run test 3. Component that is called out in warning statement 4. Component under test |
| 175-198-XXX Thermal Sensor(s) test aborted |
1. If a component is called out, make sure it is enabled and/or connected 2. Flash the system and re-test 3. Go to "Undetermined Problems" |
| 175-199-XXX Thermal Sensor(s) test failed, cause unknown |
1. Go to "Undetermined Problems" 2. Flash the system and re-test 3. Replace component under function test. |
| 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error |
1. Check fans 2. Check Power supply 3. Microprocessor 4. System board |
| 185-000-XXX Asset Security Test Passed |
1. No action |
| 185-XXX-XXX Asset Security failure |
1. Assure Asset Security Enabled 2. Flash system 3. System board |
| 185-278-XXX Asset Security Chassis Intrusion |
1. C2 Cover Switch 2. System board |
| 201-000-XXX System Memory Test Passed |
1. No action |
| 201-XXX-XXX System Memory error |
1. Replace the memory module called out by the test 2. System board |
| 202-000-XXX System Cache Test Passed |
1. No action |
| 202-XXX-XXX System Cache error |
1. Cache, if removable 2. System board 3. Microprocessor |
| 206-000-XXX Diskette Drive Test Passed |
1. No action |
| 206-XXX-XXX Diskette Drive error |
1. Diskette Drive Cable 2. Check power supply voltages 3. Diskette drive 4. System board |
| 215-000-XXX CD-ROM Drive Test Passed |
1. No action |
| 215-XXX-XXX CD-ROM Drive error |
1. CD-ROM Drive Cable 2. Check power supply voltages 3. CD-ROM drive 4. System board |
| 217-000-XXX Hard Disk Drive Test Passed |
1. No action |
| 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error |
1. Hard Disk Drive Cable 2. Check power supply voltages 3. Hard Disk drive (IDE) 4. System board |
| 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error |
1. Hard Disk Drive Cable 2. Check power supply voltages 3. Hard Disk drive (SCSI) 4. SCSI adapter card 5. System board |
| 220-000-XXX Hi-Capacity Cartridge Drive Test Passed |
1. No action |
| 220-XXX-XXX Hi-Capacity Cartridge Drive error |
1. Remove the Hi-Capacity Cartridge Drive and re-test the system |
| 301-000-XXX Keyboard Test Passed |
1. No action |
| 301-XXX-XXX Keyboard error |
1. Keyboard 2. Check and test Mouse 3. System board |
| 302-000-XXX Mouse Test Passed |
1. No action |
| 302-XXX-XXX Mouse error |
1. Mouse 2. Check and test Keyboard 3. System board |
| 303-000-XXX Joystick Test Passed |
1. No action |
| 303-XXX-XXX Joystick error |
1. Remove the Joystick and re-test the system |
| 305-000-XXX Monitor DDC Test Passed |
1. No action |
| 305-250-XXX Monitor DDC self test failure |
1. Run Setup to enable DDC 2. Cable 3. Monitor 4. Video card 5. System board |
| 415-000-XXX Modem Test Passed |
1. No action |
| 415-XXX-XXX Modem error |
1. Remove the Modem and re-test the system |
Document Location
Worldwide
[{"Type":"HW","Business Unit":{"code":"BU016","label":"Multiple Vendor Support"},"Product":{"code":"QU02OYG","label":"Older System x->Netfinity 3000->8476"},"Platform":[{"code":"PF025","label":"Platform Independent"}],"Line of Business":{"code":"","label":""}}]
Was this topic helpful?
Document Information
Modified date:
23 January 2019
UID
ibm1DDSE-42CSAM