PM70759: DSP0300I INTERNAL DBRC ERROR DSPURI00(PM59495 )+X093A #01 TERM/DUMP DIAG=RECON:NO ACTIVE DATA SETS FOUND. PRA IN USE

Obtain the fix for this APAR.

APAR status

• Closed as program error.

Error description

• When using Parallel RECON Access (PRA)this error occurred.
  DSP0300I INTERNAL DBRC ERROR DSPURI00(PM59495 )+X093A #01
  TERM/DUMP DIAG=RECON:NO ACTIVE DATA SETS FOUND
  
  Caused by SMSVSAM failure. IMS did not fail. GENJCL jobs did
  fail. It is an issue with GENJCL command processingwhere it is
  doing some processing not in an order that is expected by DBRC
  I/O processor. It caused an issue with PRA retry handling.
  

Local fix

Problem summary

• ****************************************************************
  * USERS AFFECTED: All users of IMS V12 with parallel RECON     *
  *                 access enabled.                              *
  ****************************************************************
  * PROBLEM DESCRIPTION: An ABEND U2480 for no active data sets  *
  *                      can occur if a quiesce close is done    *
  *                      a job processing the end quiesce        *
  *                      encounters a retriable error AND the    *
  *                      next request for the job is a GENJCL    *
  *                      command or any DBRC command and         *
  *                      DBRC command authorization is enabled.  *
  ****************************************************************
  * RECOMMENDATION: INSTALL CORRECTIVE SERVICE FOR APAR/PTF      *
  ****************************************************************
  The abend occurs because the RECON data sets remain closed
  if the end-quiesce process encounters a retriable error during
  the open process of end-quiesce.  The logic expects the next
  I/O services request to be a logical open at which time it will
  try to re-open the RECON data sets before processing it.
  
  In the case of GENJCL and command authorization processing,
  a request to get the RECON data set names is made before
  the logical open which cause ABENDU2480 because there is no
  open RECON data set.
  

Problem conclusion

• GEN:
  KEYWORDS:
  
  *** END IMS KEYWORDS ***
  Since logical open processing will already take care of the
  situation when the RECONs are still closed after an end-quiesce,
  logic should be added around the DSPRCNFG SETRCDSN requests
  so that the RECONs are logically opened then closed.
  
  DSPDCAI0 is changed to add DSPROPEN and DSPRCLOS around the
           DSPRCNFG request. Since these can introduce non-zero
           return codes, a logic is added to propagate any non-
           zero return code from these calls.
  
  DSPJCMAI is changed to add DSPROPEN and DSPRCLOS around the
           DSPRCNFG request. Since these can introduce non-zero
           return codes, a logic is added to propagate any non-
           zero return code from these calls.
  
  DSPSTART is changed to correct the generation of V12 ID level.
  

Temporary fix

• *********
  * HIPER *
  *********
  

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

  PM70774 PM77918 UK90181

Modules/Macros

•    DSPDCAI0 DSPJCMAI
  

Fix information

• Fixed component name

  IMS V12

• Fixed component ID

  5635A0300

Applicable component levels

• R200 PSY UK90181

     UP12/12/12 P F212 Ž

Fix is available

• Select the PTF appropriate for your component level. You will be required to sign in. Distribution on physical media is not available in all countries.