IBM Support

OA57974: IF NO CKFREEZE FILE IS SELECTED WHEN ENTERING THE RESOURCE SET OF PANELS FOR CICS, NOT POSSIBLE TO ENTER SE.1 JUMP COMMAND

A fix is available

Subscribe

You can track all active APARs for this component.

 

APAR status

  • Closed as program error.

Error description

  • When entering the Resource panels under the Resource option from
    the zSecure ISPF menu, and then choosing the CICS option, an
    error message of "NO CKFREEZE FILE" is displayed when you have
    not previously added a CKFREEZE file via option Se.1
    
    If you enter a jump command of =SE.1, the "NO CKFREEZE FILE"
    message is redisplayed and you are unable to continue and must
    PF3 out of the panel or enter the command "SETUP FILES" to go to
    option Se.1
    

Local fix

  • Enter SETUP FILES instead of the jump command to be taken to the
    panel for adding files to your working environment.
    
    Use SETUP FILES command instead of =SE.1 jump command
    

Problem summary

  • ****************************************************************
    * USERS AFFECTED: Users of zSecure Admin/Audit exploiting the  *
    *                 resource reports in interactive mode (option *
    *                 RE.<x>).                                     *
    ****************************************************************
    * PROBLEM DESCRIPTION: zSecure Admin/Audit does not follow an  *
    *                      ISPF 'jump' command on the RE.<x>       *
    *                      panels in cases where no CKFREEZE data  *
    *                      set is specified.                       *
    ****************************************************************
    * RECOMMENDATION: Apply the PTF provided.                      *
    ****************************************************************
    When no CKFREEZE data set is specified in the input files
    configuration, the zSecure Admin/Audit correctly displays
    a message 'No CKFREEZE file' when RE.<x> primary command is
    entered. However the subsequently entered ISPF 'jump' commands
    (=SE.1, for example) are not followed and the 'No CKFREEZE file'
    message is redisplayed.
    

Problem conclusion

  • zSecure Admin/Audit has been modified so that the ISPF 'jump'
    commands are properly handled in the RE.<x> panels.
    

Temporary fix

Comments

APAR Information

  • APAR number

    OA57974

  • Reported component name

    ZSEC BASE,ADMIN

  • Reported component ID

    5655T0100

  • Reported release

    231

  • Status

    CLOSED PER

  • PE

    NoPE

  • HIPER

    NoHIPER

  • Special Attention

    NoSpecatt / Xsystem

  • Submitted date

    2019-07-18

  • Closed date

    2019-08-28

  • Last modified date

    2019-09-01

  • APAR is sysrouted FROM one or more of the following:

  • APAR is sysrouted TO one or more of the following:

    UJ00599

Modules/Macros

  • C2RNIDNE C2RNIDNJ CKRI00   CKRI21   CKRP3AM@ CKRP3AR@ CKRP3DB@
    CKRP3DBM CKRP3EZM CKRP3IM@ CKRP3IMR CKRP3IP@ CKRP3MQ@ CKRP3MQM
    CKRP3RHM CKRP3RJM CKRP3RKM CKRP3ROM CKRP3RPM CKRP3TS@ CKRP3TSR
    CKRP3UT@ CKRP3UXM CKRP3VMM CKRP3VT@ CKRP3VTM
    

Fix information

  • Fixed component name

    ZSEC BASE,ADMIN

  • Fixed component ID

    5655T0100

Applicable component levels

  • R231 PSY UJ00599

       UP19/08/29 P F908

Fix is available

  • Select the PTF appropriate for your component level. You will be required to sign in. Distribution on physical media is not available in all countries.

[{"Business Unit":{"code":"BU048","label":"IBM Software"}, "Product":{"code":"SSCE68R","label":"zSecure Admin"},"Component":"","ARM Category":[],"Platform":[{"code":"PF025","label":"Platform Independent"}],"Version":"231","Edition":""}]

Document Information

Modified date:
01 September 2019