HD75552: AEROSPACE SHEET METAL DESIGN : JOGGLE COMPENSATION

APAR status

• Closed as program error.

Error description

• AEROSPACE SHEET METAL DESIGN : JOGGLE
  COMPENSATION VALUE IS DISREGARDED
  Scenario:
  1. Open CATPart
  2. Change to Aerospace Sheet Metal Design work
  bench
  3. Select Fold/Unfold Icon in Aerospace Sheet Metal
  tool bar
  4. Measure the compensation amount in the flat
  view (Value
  measures 1.66 in) Compensation length should not
  exceed the
  value in the Method1.txt document (1.5 in)
  5. Change Plane 4 value to 9 inches
  Error Message Corner operator: Impossible to
  compute
  eventual center of corner between element 1 &
  element 2 edges.
  6. Select OK
  7. Select Cancel
  8. Double Click on Surfacic
  Flange.1+Compensation tab
  Uncheck the Apply Compensation tab
  9. Change Plane 4 value to 9 inches
  10. Part is now created with no compensation.
  The joggle compensation value should be limited to
  the value in
  the Method1. txt design table. The value in the
  included design
  table is 1.50 inches. Currently the compensation is
  applied the
  entire length between the joggle planes. If the
  second joggle
  plane is increased to a large distance CATIA will
  not build the
  part when joggle compensations are applied.
  .
  

Local fix

Problem summary

• AEROSPACE SHEET METAL DESIGN : JOGGLE COMPENSATION
  VALUE IS DISREGARDED
  AEROSPACE SHEET METAL DESIGN : JOGGLE
  COMPENSATION VALUE IS DISREGARDED
  Scenario:
  1. Open CATPart
  2. Change to Aerospace Sheet Metal Design work
  bench
  3. Select Fold/Unfold Icon in Aerospace Sheet Metal
  tool bar
  4. Measure the compensation amount in the flat
  view (Value
  measures 1.66 in) Compensation length should not
  exceed the
  value in the Method1.txt document (1.5 in)
  5. Change Plane 4 value to 9 inches
  Error Message Corner operator: Impossible to
  compute
  eventual center of corner between element 1 &
  element 2 edges.
  6. Select OK
  7. Select Cancel
  8. Double Click on Surfacic
  Flange.1+Compensation tab
  Uncheck the Apply Compensation tab
  9. Change Plane 4 value to 9 inches
  10. Part is now created with no compensation.
  The joggle compensation value should be limited to
  the value in
  the Method1. txt design table. The value in the
  included design
  table is 1.50 inches. Currently the compensation is
  applied the
  entire length between the joggle planes. If the
  second joggle
  plane is increased to a large distance CATIA will
  not build the
  part when joggle compensations are applied.
  .
  

Problem conclusion

• NOTE THAT THIS PROBLEM WILL ALSO BE FIXED ON V5R19SP01
  AND ON R20GA
  Incident Diagnosis
  JOGGLE COMPENSATION VALUE IS DISREGARDED
  Correction Explanation
  An error has been found in the CATIA code during
  the compensation check.The feature is now
  corrected
  Answer and By-Pass
  The 2 Joggles must be deleted and re-created
  because this correction is versionned to ensure
  existing topology stability.
  The problem is not fixed on r18 because it modified the
  UnFolded result of the Surfacic Flange and should be
  versionned. The versionning is no more available on r18
  because r19 is now GA.
  .
  

Temporary fix

Comments

APAR Information

• APAR is sysrouted FROM one or more of the following:

• APAR is sysrouted TO one or more of the following:

Fix information

• Fixed component name

  CATIA V5 NT>XP

• Fixed component ID

  569151000

Applicable component levels

• R518 PSN

     UP