Feature codes for the TS4500

This triggers the shipment of a JK diagnostic cartridge. When model L25 is ordered or when FC 9080 (Mixed Media) is ordered for model L55, a minimum of one of FC 1404 or 1406 is required but any may be selected.

This triggers the shipment of an L5 diagnostic cartridge. When model L55 is ordered, a minimum of one of FC 1405 or 1407 is required but both can be selected. When FC 9080 (Mixed Media) is ordered for model L25, a minimum of one of FC 1405 or 1407 is required but both can be selected.

This feature provides a JL diagnostic cartridge. When model L25 is ordered or when FC 9080 (Mixed Media) is ordered for model L55, a minimum of one of FC 1404 or 1406 is required but any may be selected.

This triggers the shipment of an L6 CE cartridge. When model L55 is ordered, a minimum of one of FC 1405 or 1407 is required but both can be selected. When FC 9080 (Mixed Media) is ordered for model L25, a minimum of one of FC 1405 or 1407 is required but both can be selected.

This triggers the shipment of an L7 CE cartridge. When model L55 is ordered, a minimum of one of FC 1407 or 1408 is required but both can be selected. When FC 9080 (Mixed Media) is ordered for model L25, a minimum of one of FC 1407 or 1408 is required but both can be selected.

This triggers the shipment of an L8 CE cartridge. Only one L8 CE cartridge feature #1409 is required in a TS4500 Library.

Prerequisite: One of either feature #1408 or #1409 is a prerequisite for the first TS1080 (3588 Model F8x) tape drive ordered. Feature #1409 is a prerequisite for the first TS1090 (3588 Model F9x or S9C) Tape drive ordered.

This feature provides a mini SAS HD wrap tool. Only one tool is required for the library. The wrap tool is used to isolate drive sled problems

Includes 1x LCC and 2x power supplies.

This provides power and internal network redundancy for the L25/L55 frame. This is a prerequisite to FC 9002.

Provides mounting hardware only.

This feature provides signal and power cabling for a column of 4 adjacent drives. Fiber cables can be ordered via one of the following:

This feature is not supported in the leftmost frame of a dual accessor library.

This feature provides signal and power cabling for a column of 4 adjacent drives. Fiber cables can be ordered via one of the following:

This feature is not supported in the leftmost or rightmost frame of a dual accessor library.

This feature provides signal and power cabling for a column of 4 adjacent drives. Fiber cables can be ordered via one of the following:

• FC 1536, MMF Quad Drive-to-Patch Panel cables
• FC 1537, SMF Quad Drive-to-Patch Panel cables
• FC 9713, No Patch Panel Cables

This feature is not supported in the leftmost frame of a single accessor library.

This feature is not supported in the leftmost or rightmost frame of a dual accessor library.

This feature includes all fiber cables required for a column of 4 drives, 8x LC-LC Multimode Fiber (MMF) Drive-to-Patch Panel cables.

Prerequisite: One FC 1536 or 1537 or 9713 per each FC 1531, 1532, 1533, and 1534.

This feature includes all fiber cables required for a column of 4 drives, 8x LC-LC Single Mode Fiber (SMF) Drive-to-Patch Panel cables.

Prerequisite: One FC 1536 or 1537 or 9713 per each FC 1531, 1532, 1533, and 1534.

Provides license keys to enable transparent LTO encryption.

Provides magazine and cover for transport or storage of up to 18 cartridges.

Provides magazine and cover for transport or storage of up to 16 cartridges.

Provides license key to increase storage from entry capacity to intermediate capacity.

Provides license key to increase storage from intermediate capacity to base capacity.

This feature code is a prerequisite for FC 9002 or Model Lx5 HD CoD FC 164x.

Prerequisite: FC 1643

Prerequisite: FC 1644

Prerequisite: FC 1644

This feature code adds either 36 (LTO) or 32 (3592) I/O slots.

This includes 1x top panel and 2x Ethernet cables, card cages, ASCs, BPCs, and LFIs.

This feature provides left-and right-side end covers. This feature is required only for the first top rack ordered (if multiple top racks are installed on adjacent frames).

Each PDU has 10 C13 outlets divided into 2 groups of 5 outlets. Each group is protected by a 15 amp circuit breaker. In addition, there is a master 25 amp circuit breaker for the entire PDU. All of the circuit breakers are rated at 5 kAIC. Each PDU has a control input that can be used to turn all of the outlets on or off by an external switch or relay contact (not provided). The control input is defaulted to ON by a jumper plug included with the PDU.

Prerequisite: For each FC 1751 ordered, one power cord (FC 9954 through 9959 or 9966) must also be ordered.

Limitation: Mutually exclusive with 1752

Provides one PDU with 3-phase (wye) or single phase input power, to be mounted in top rack (max of two may be ordered). Each PDU ordered in a top rack consumes 1U of rack space.

Each PDU has 9 outlets divided into three groups. Within each group there are two C-13 outlets and one C-19 outlet. Each group is protected by 20amp circuit breakers rated at 10 kAIC. Note that, if required, loads installed in the TR1 with C14 inlets can be connected to the PDU C19 outlets by use of C20 to C13 power cord FC 9949.

Prerequisite:

• For single phase input power, for each PDU ordered must order one power cord FC 9954 through 9958.
• For 3-phase (wye) input power, for each PDU ordered must order one power cord FC 9948.

Limitation: Mutually exclusive with FC 1751

This feature code specifies the configuration of the TR2 rack to be in conformance with the Open Compute Project Olympus Rack Specification.

This provides 5U of 19 inch rack space with 3 sets of EIA rails with a spacing from the front face of the front EIA rail to the rear face of the middle EIA rail being 745 mm and the spacing from the front face of the front EIA rail to the rear face of the rear EIA rail to be 1020 mm.

It includes a top cover that allows top access cables to be routed into the TR2. This also includes side air blocks that prevent airflow between the EIA rails and the side covers per the Open Compute Olympus Rack Specification

This feature code specifies the configuration of the TR2 rack to be in conformance with industry standard 19 inch racks.

This provides 5U of 19 inch rack space with 2 sets of EIA rails with a spacing from the front face of the front EIA rail to the rear face of the rear EIA rail being 719 mm.

It includes a top cover that allows top access cables to be routed into the TR2.

This feature provides the front door for the TR2

This feature provides the rear door for the TR2

Non-HA 1 to 2 Frame Track Cable

Non-HA 3 to 6 Frame Track Cable

Non-HA 7 to 14 Frame Track Cable. See 3584 X Track Cable Features/Specify codes for more details.

Limitation: Not supported with FC 2071 or FC 9071.

Non-HA 9 to 18 Frame Track Cable. See 3584 X Track Cable Features/Specify codes for more details.

Limitation: Not supported with FC 2071 or FC 9071.

Allows attachment of a powered frame to a single outlet while also maintaining drive redundant power.

Provides two PCAs, mounting hardware including rack brackets, and internal power cables.

Supports any combination of up to 3 pairs of power cords for FC 4875 on the same frame and FC 9989 on adjacent frames.

Each PDU has 10 C13 outlets divided into 2 groups of 5 outlets. Each group is protected by a 15 amp circuit breaker. In addition, there is a master 25 amp circuit breaker for the entire PDU. All of the circuit breakers are rated at 5 kAIC. Each PDU has a control input that can be used to turn all of the outlets on or off by an external switch or relay contact (not provided). The control input is defaulted to ON by a jumper plug included with the PDU.

Corequisite: One power cord feature (FC 9954 through 9959 or 9966)

Limitation: FC 1951 cannot be installed in the same rack as an FC 1952 PDU.

Provides two PDUs with 3-phase (wye) or single phase input power, mounting hardware including rack brackets, and internal power cables to provide power to the local frame control assembly.

These line cord features may require different customer facility outlets than frames without FC 1952. Can be used for adjacent frame AC power cord aggregation, or for unique facility AC socket requirements. Supports any combination of up to 3 pairs of power cords for FC 9989 on adjacent frames.

Each PDU has 9 outlets divided into three groups. Within each group there are two C-13 outlets and one C-19 outlet. Each group is protected by 20amp circuit breakers rated at 10 kAIC. Note that, if required, loads installed in the TR1 with C14 inlets can be connected to the PDU C19 outlets by use of C20 to C13 power cord FC 9949.

Prerequisite:

This includes AXY, AXY plate, ASC to Flex track cable, and new end stops.

Provides a complete accessor assembly with HD grippers to Lxx models or models with FC 1442.

Prerequisite: FC 2071, 2072, or 9071, 9072.

Provides a 26-port Ethernet switch and attachment cable for connection to an IMC as a centralized system console.

Up to 24 extra connections of FC 2715 are provided by this feature. This feature is supported on Lx5 models to allow other products to share the IMC.

FC 2715 is a cable to attach a unit to the Ethernet switch provided by the TSSC.

Required for all new plant orders. Provides a USB optical drive for use with the Integrated Management Console (IMC). The optical drive is required for IMC code.

This feature allows longer distances between the IMC end panel and an FCA by supplying 2 Ethernet cables that are longer than normal. For both plant and field, instructions are also provided for moving the IMC PDU from another frame into this frame.

Prerequisite: One of the FC 9970-9985, 9989 power cords.

Provides 2x Fibre channel switch mounting hardware, including rack brackets and power cords.

Prerequisite: FC 4880

Provides 1x Fibre channel switch (16 Gb).

Limitation: There is a maximum of 2x FC 4880 per model x25.

This feature provides the brackets and accessories for a system integrator to pre-load media.

Prerequisite: FC 9074

This feature provides rear door sensor components for notifying of rear door open/close events.

Prerequisite: FC 9074

Universal cleaning cartridge.

Used as a part of the process to add any Dxx or Sxx frame.

Used as a part of the process to add any Dxx or Sxx frame.

Prerequisites: One Flex-track A and B cable of the same length.

Flex-Track A cable: FC 2002, 2006, 2014, or 2018.

Flex-Track B Cable: FC 2402, 2406, 2414, or 2418.

Includes AXY, AXY plate, ASC to Flex track cable, and new end stops.

This feature indicates that the frame is capable of supporting Enhanced PDUs and their associated power cords. FC 9073 is a prerequisite for ordering FC 1952.

This feature indicates the frame includes third generation modifications to support future enhancements.

Prerequisite: Library must contain a mix of LTO and 3592 frames.

Limitation: Mixed media not supported for Lx2/Lx3.

This feature informs the plant to install one LTO 7 Tape Drive Model F7A/ F7C (3588 Model F7A or F7C) into a Tape Library Model D55, or L55 coming from the plant.

This feature informs the plant to install one LTO 8 Tape Drive Model F8A/F8C (3588 Model F8A or F8C) into a Tape Library Model D55, or L55 coming from the plant.

Installation of a 3588 Tape Drive canister requires that a Quad Drive Mounting Kit feature (FC 1521, 1522, 1523, 1524 or 1531, 1532, 1533, 1534) be installed in the TS4500 frame to contain the canister.

This feature informs the plant to install one LTO 8 Tape Drive Model F8S (3588 Model F8S) into a Tape Library Model D55 or L55 coming from the plant.

This feature informs the plant to install one TS1090 Tape Drive Model F9C (3588 Model F9C) into a new TS4500 Tape Library Model D55 or L55 coming from the plant.

This feature informs the plant to install one TS1090 Tape Drive Model F9S (3588 Model F9S) into a new TS4500 Tape Library Model D55 or L55 coming from the plant.

This feature informs the plant to install one TS1090 Tape Drive Model S9C (3588 Model S9C) into a new TS4500 Tape Library Model D55 or L55 coming from the plant.

This specify code notifies the plant to factory install a new 3592 Tape Drive into a new 3584 Tape Library Frame coming from the plant.

This code must appear on the tape drive order and also the Plant Install 3592 E05 in a 3584 feature (FC 9680) or Plant Install 3592 E06 in a 3584 feature (FC 9683) or Plant Install 3592 E07/EH7 in a 3584 feature (FC 9692) or Plant Install 3592 E08/EH8 in a 3584 feature (FC 9699) or Plant Install 3592 55E in a 3584 feature (FC 9704) or Plant Install 3592 55F/55G in a 3584 feature (FC 9705) or Plant Install 3592 60F in a 3584 feature (FC 9706) or Plant Install 3592 60E in a 3584 feature (FC 9707) or Plant Install 3592 60S in a 3584 feature (FC9708) must appear on the 3584 Frame order.

This feature notifies the plant to ship one 3592 Tape Drive, which will be field installed in a 3584 Tape Library Frame.

This code must appear on the tape drive order and also the Field Merge 3592 Tape Drive (FC 1674) or (FC 1675) or (FC 1676) for a 3592 E07/E08/55G/60G, (FC 9690) for a 3592 EH7/EH8/55E/55F or (FC 9726) for a 3592 60E/60F/60S must appear on the 3584 Tape Library Frame order.

This feature field installs one 3592 Model EH7, EH8, 55E or 55F. Or one 3588 Model F5C, F6C, F7C, F8C, F8S Tape Drive into an installed 3584 Model D25 or L25, or D55 or L55. This feature is also required to field merge a 3592 Model EH7, EH8, 55E, 55F, or 3588 Model F5C, F6C, F7C, F8C, F8S Tape Drive into a 3584 frame coming from the plant. The Tape Drive requires a Quad Drive mounting kit to contain the drive.

FC 9692 is a manufacturing routing code.

Prerequisite: FC 152x (drive mounting kit). Each FC 152x supports up to 4 of FC 969x.

FC 9695 is a manufacturing routing code.

Prerequisite: FC 152x/153x (drive mounting kit). Each FC 152x/153x supports up to 4 of FC 969x.

FC 9697 is a manufacturing routing code.

Prerequisite: FC 152x/153x (drive mounting kit). Each FC 152x/153x supports up to 4 of FC 969x.

FC 9699 is a manufacturing routing code.

Prerequisite: FC 152x (drive mounting kit). Each FC 152x supports up to 4 of FC 969x.

This feature tells the plant to install one 3592 Tape Drive Model 60F into a 3584 Model D25 or Model L25 coming from the plant.

Prerequisite: Installation of the 3592 Model 60F Tape Drive requires a Quad Drive mounting kit to contain the drive. Mounting Kit feature (FC 1515) or (FC 1535).

This feature tells the plant to install one 3592 Tape Drive Model 60E into a 3584 Model D25 or Model L25 coming from the plant.

This feature should be specified if you do not want the factory to ship any Fiber Channel cable FC 1536 “MMF Quad Drive-to-Patch Panel cables” or FC 1537 “SMF Quad Drive-to-Patch Panel cables”.

This feature field installs one 3592 Model 60E or 60F or 60S Tape Drive into an installed 3584 Model D25 or L25. This feature is also required to field merge a 3592 Model 60E or 60F Tape Drive into a 3584 frame coming from the plant.

This feature originally indicated that the customer would allow broadband Call Home; however, the feature code is no longer utilized.

This feature provides a 4.3 meter (14 foot) long power cord with an IEC 309 3P+N+G 32A plug, rated for 230 Vac, 24 Amps. This power cord supports 3 phase (wye) power. To be used with Enhanced PDU FC 1752 or 1952.

This feature provides a 2.8 meter long C20-C13 Power Cord to be used between computer equipment and the Enhanced PDU FC 1752 or 1952 or customer-supplied PDU with C19 outlets. C13 connects to the male C14 inlet or power cord plug and the C20 mates with the C19 receptacle on the Enhanced PDU. This power cord is intended to be used on PDUs with C19 outlets.

FC 9954 is used with PDU FCs 1751 and 1752 (in model TR1) or 1951 and 1952 (in model xx5). FC 9954 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

FC 9955 is used with PDU FC 1751 and 1752 (in model TR1) or 1951 and 1952 (in model xx5). FC 9955 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

FC 9956 is used with PDU FC 1751 and 1752 (in model TR1) or 1951 and 1952 (in model xx5). FC 9956 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

FC 9957 is used with PDU FC 1751 and 1752 (in model TR1) or 1951 and 1952 (in model xx5). FC 9957 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

FC 9958 is used with PDU FC 1751 and 1752 (in model TR1) or 1951 and 1952 (in model xx5). FC 9958 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

FC 9959 is used with PDU FC 1751 (in model TR1) or 1951 (in model xx5). FC 9959 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

Limitation: Not supported with FC 1752 or 1952.

FC 9966 is used with PDU FC 1751 (in model TR1) or 1951 (in model xx5). FC 9966 provides 1x power cord when ordered on a model TR1 and 2x power cords when ordered on a model xx5.

Limitation: Not supported with FC 1752 or FC 1952.

FC 9970 includes model-dependent contents. For countries other than the United States and Canada, the connector is rated at 16A (plug type Hubbell HBL316P6W or equivalent) for connection to Hubbell type HBL316R6W or equivalent receptacles.

In the United States and Canada, the connector is rated at 20A (plug type Hubbell HBL320P6W) for connection to Hubbell type HBL320R6W or equivalent receptacles. This is the default power cord for all countries other than those specified for FC 9972 and FCs 9976 through 9983.

FC 9972 includes model-dependent contents. It is the default power cord for US, Canada, Japan, Korea, Philippines, and Taiwan.

FC 9984 is 2x power cords which are UL / CSA certified for use in US and Canada. These power cords mate with customer-supplied NEMA L6-20R receptacles.

FC 9985 is 2x power cords which are UL/CSA certified for use in US and Canada. These power cords mate with customer-supplied Russellstoll 3743U2 or 9R23U2W receptacles.

FC 9989 is for use with adjacent frame PDUs (FC 1951) or external (customer-supplied) PDUs.

3meters Mini-SAS HD to Mini-SAS HD cable for attachment of up to four Tape Drives in the same column.

10 Meter OM3 Fiber Cable (LC)

Order the number of this feature code for each drive to be connected.

25 Meter OM3 Fiber Cable (LC)

Order the number of this feature code for each drive to be connected.

80 Meter OM3 Fiber Cable (LC)

Order the number of this feature code for each drive to be connected.

3 Meter OM3 Fiber Quad Cables (LC)

To attach tape drives in the same frame or 1 frame away from a model x25 frame containing TS7700 BE switches, order one of this feature code for each quad-drive mounting kit to be connected.

For xx5 models, each FC AGKQ has a prerequisite of an associated FC 152x or 153x.