Displaying storage management subsystem information

Use the DISPLAY SMS command to display the following kinds of information about the Storage Management Subsystem (SMS):

Active SMS configuration
3990-3 or 3990-6 cache control unit statistics (if the 3990-3 or 3990-6 is installed and has at least one system-managed volume attached)
Status of system-managed volumes, storage groups, drives, or libraries
SMS trace options in effect
SMSVSAM status of sharing control data sets, the SMSVSAM server, data set statistical monitoring, coupling facility cache and lock structures and cache structures that contain data for a specified volume
CICSVR status of Recovery Control Data sets (RCDSs) and the status of the CICSVR address space.

Storage groups and volumes can be in one of the following states:

Not defined means that the storage group or volume (specified on this command) is specified in the SMS configuration as not being connected to this MVS™ system. If the storage group or volume is not defined in the active configuration, a message indicates that the system rejects this command for that reason. If the command is issued for a storage group with no volume, another message indicates the lack of volumes in that group. The symbol for this state is ‘.’
Enabled means that SMS permits allocation of data sets in this storage group or volume to this MVS system. The symbol for this state is ‘+’
Disabled means that SMS does not allow allocation of data sets in this storage group or volume for this MVS system. The symbol for this state is ‘–’
Disabled (new only) means that SMS does not allow allocation of new data sets in this storage group or volume for this MVS system. The symbol for this state is ‘D’
Quiesce means that for a data set, SMS selects the specified volume or storage group only if it finds no other choices. The symbol for this state is ‘*’
Quiesce(new) means that for a new data set, SMS selects the specified volume or storage group only if it has no other choices. The symbol for this state is ‘Q’

For a detailed discussion of the DISPLAY SMS command pertaining to optical and tape volumes, libraries, and drives, and the OAM address space, see z/OS DFSMS OAM Planning, Installation, and Storage Administration Guide for Object Support, and the z/OS DFSMS OAM Planning, Installation, and Storage Administration Guide for Tape Libraries.

Figure 1. DISPLAY SMS command syntax

D SMS[,{ACTIVE|A}                                         ]
                                                 
     [,CACHE                                              ]
                                                 
     [,CFCACHE({structurename|*})                         ]
                                                 
     [,CFLS(ALL|lockstructurename)                       ]
                                                 
     [,CFVOL(volid)                                       ]
     [,CICSVR[,{ALL|LOGSTREAMS({LogstreamName|ALL})|RCDS} ] 
     [,{DRIVE|DRI}({name|ALL})[ ,STATUS   ]
                               |,DETAIL                   ]
     [,DSNAME(dsn){,WTOR}                                 ]
     [,JOB(jobname){,WTOR}                                ]
                                                 
     [,{LIBRARY|LIB}({name|ALL})[ ,STATUS[,LISTDRI]]   
                                 |,LISTDRI            
                                 |,DETAIL                 ]
     [,LOG({logstreamid|ALL}{,WTOR}                       ]
     [,MONDS({specmask|*})                                ]
                                                
     [,OAM                                                ]
                                                 
     [,OPTIONS                                            ]
                                                 
     [,OSMC[,TASK(name)]                                  ]
     [,{PDSE|PDSE1}{,LATCH(laddr)[,DETAILED]               }]
                                 |,SUMMARY
                   {,MODULE(modname)                       }
                   {,VSTOR                                 }
                   {,HSPSTATS[,DSN(dsname)][,STORCLAS(sc)]]}
                                           |,UNMANAGED
                             [,SUMMARY                    ]
                             [,MAXDSNS(maxds)             ] 
                   {,CONNECTIONS,DSN(dsname)[,VOL(volser)]
                                                            
     [,SEP                                                ] 
     [,SHCDS                                              ]
     [,SHUNTED,{SPHERE(sphere)|UR({urid|ALL}}{,WTOR}      ]
                                                 
     [,SMSVSAM[,ALL]                                      ]
                                                 
     [,SMSVSAM,QUIESCE                                    ]
                                                 
     [,SMSVSAM,DIAG({CONTENTION|C})                       ]
     [,{STORGRP|SG}{(storgrp|ALL)}[ ,LISTVOL ]       
                                   |,DETAIL               ]
     [,{TRACE|T}                                          ]
     [,TRANVSAM[,ALL][,ALLLOGS][,WTOR]                    ]
     [,URID({urid|ALL}){,WTOR}                            ]
                                                 
     [,{VOLUME|VOL}(volume)                               ]
     [,VOLSELMSG                                          ]
     [,L={a|name|name-a}                                  ]

SMS

Displays information about the Storage Management Subsystem. If SMS is the only operand specified, this command displays the active SMS configuration.

ACTIVE or A

The display includes the names of the three main SMS system data sets currently in use: the active control data set (ACDS), the communications data set (COMMDS), and the source control data set (SCDS). The display also includes the interval (DINTERVAL), in seconds, that SMS waits between reading device statistics for the 3990-3 control unit. In addition, the display shows the values of the REVERIFY and ACSDEFAULTS parameters in the IGDSMSxx parmlib member.

The display also includes a list of the MVS systems and system groups in the complex. For each system or system group, the display shows a date and time stamp that indicates the level of its SMS configuration, and the synchronizing interval value for its SMS subsystem (not the same as DINTERVAL). This synchronizing interval is the number of seconds that an SMS subsystem delays before synchronizing with the other SMS subsystems in the complex. A longer interval setting enables a slower system to avoid being locked out from accessing the communications data set. For more information on the SMS control data sets, the levels of SMS configuration, and the synchronizing interval, see z/OS DFSMSdfp Storage Administration.

CACHE

Displays the following information for each 3990-3 or 3990-6 control unit that has at least one system-managed volume attached to it:

SSID: Four-character identifier for the subsystem
SMSCNT: Number of SMS volumes attached to the cache
READ CONTROL: Percentage of reads and non-retentive writes for SMS-controlled data sets that will use the cache
FAST WRITE CONTROL: Percentage of writes with SMS-controlled data that will use the fast write feature
READ HIT RATIO: Percentage of I/O requests that make a hit in the cache
FAST WRITE RATE: Number of DASD fast write bypasses per minute due to non-volatile storage (NVS) overload.

CFCACHE(structurename or *)

Displays information about cache structures in the coupling facility. Specify structurename to display information for a given structure. Specify '*' to display information for all cache structures.

CFLS[,ALL|lockstructurename]

Displays the following information about the coupling facilities lock structure:

Size
Status
Contention rate
False contention rate

D SMS,CFLS[,ALL] display information for all lock structures known to VSAM RLS including IGWLOCK00.

D SMS,CFLS(lockstructurename) returns information for the single lock structure specified. The lock structure name can be specified as IGWLOCK00. Only systems with the multiple lock structure support display information about secondary lock structures.

If no lock structure name is specified, IGWLOCK00 is displayed.

CFVOL(volid)

Displays a list of coupling facilities cache structures that contain data for the specified volume (volid) and the status of the volume.

CICSVR[,{ALL|LOGSTREAMS(LogstreamName|ALL)|RCDS}]

Displays overall information concerning the CICSVR address space.

[ALL] is specified. The command returns the requested information from all of the active CICSVR address spaces within the sysplex.
[LOGSTREAMS(LogstreamName|ALL)] allows the operator to view all the logstreams that are currently connected to the CICSVR address space. If ALL is specified, the system displays information about all the logstreams in use and known to CICSVR on the system on which the command is issued. If a LogstreamName is specified, the system displays only the information regarding that specific logstream.
[RCDS] returns the information about the Recovery Control data sets in the CICSVR address spaces.

DETAIL

Displays detailed status information for tape and optical libraries, tape and optical storage groups and optical drives (in messages CBR1110I, CBR1120I, and CBR1130I).

If you specify a system-managed tape library name, then the system displays more detailed information about the named system-managed tape library. If you issue this command from a TSO/E terminal in OPERATOR mode, you cannot obtain detailed status for optical drives or libraries.

Note: When you specify the DETAIL keyword, you cannot specify the LISTDRI keyword.

DRIVE(name or ALL)

Displays system connectivity and the online/offline status of optical drives only. When the drive name is specified, the status for that drive is shown in a single line display. When ALL is specified the status for all the optical drives is shown.

To display the status of a drive named ALL, place the keyword in double parentheses, as DRIVE((ALL)).

Tip: To obtain the online or offline status of devices within a tape library, use the DISPLAY UNIT, DEVSERV or LIBRARY DISPDRV command.

DSNAME(dsn)

For a given fully qualified data set name, displays the jobs currently accessing the data set using DFSMS Transactional VSAM Services (DFSMStvs) access on the systems within the sysplex. If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

JOB(jobname)

Displays information about a particular job that is using DFSMStvs services on one of the systems in the sysplex. The output includes:

The name of the current step within the job
The current URID for the job
The status of the unit of recovery (in-reset, in-flight, in-prepare, in-commit, in-backout, indoubt)

If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

LIBRARY(name or ALL)

Displays system connectivity and the online or offline status of the tape and optical libraries. Specify the library name to display the status on a single line for the named library. Specify ALL to display the status for all tape and optical libraries.

If both optical libraries and system-managed tape libraries are defined in the SMS configuration, then the system or system group displays the optical library information followed by the system-managed tape library information.

To display a library named ALL, place the name in double parentheses, as LIBRARY((ALL)).

LISTDRI

Displays the offline or online status for all the optical drives associated with the specified libraries.

Restriction: When you specify the LISTDRI keyword, you cannot specify the DETAIL keyword.

LOG(logstreamid or ALL))

Displays information about a log stream that DFSMStvs is currently using on one of the systems in the sysplex. If ALL is specified, information is displayed about all of the logs in use on the entire sysplex. The output includes the status of the log stream (failed or available), type of log (undo, shunt, forward recovery, or log of logs), the job name and URID of the oldest unit of recovery using the log, and a list of all DFSMStvs instances that are using the log. If information about a specific log stream is requested and the log stream is either a system log or a forward recovery log, the output includes the names of the jobs using the log stream.

This command might be issued to determine why a log stream is increasing in size. If a unit of recovery is long running, DFSMStvs would be unable to delete any log blocks that contain data associated with the unit of recovery, which in turn would make truncation of the log stream impossible.

If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

MONDS(specmask or *)

Displays the data set specifications eligible for coupling facilities statistics monitoring. You can specify a full or partial data set name (specmask) to view a subset of the data set specifications. You must specify at least one high-level qualifier. A wildcard in the data set name cannot be followed by additional qualifiers.

Specify an asterisk (*) to display all the data set specifications eligible for coupling facilities statistics monitoring.

OAM

If both optical libraries and tape libraries are defined in the SMS configuration, then the system displays the optical library information followed by the tape library information.

Note: This operand is not valid when issued from a TSO/E terminal in OPERATOR mode.

OPTIONS

Displays all of the SMS parameters and their status, and the setting of the FAST_VOLSEL parameter at the time this command is issued. The display indicates whether each option is on or off, what data sets are being used, the size of regions, the time interval for recording data, and all other parameter specifications.

For a description of the output, see message IGD002I.

When DFSMStvs is running on the system, the output of this command includes DFSMStvs-related information.

OSMC

Displays the status of the OAM storage management component (OSMC).

Note: This operand is not valid when issued from a TSO/E terminal in OPERATOR mode.

TASK(name): Displays the OSMC status for a specific task.

STATUS

Displays online/offline status for tape or optical libraries or optical drives.

{PDSE|PDSE1},LATCH(laddr),{DETAILED|SUMMARY}

Displays the status of PDSE latch at latch address (laddr) for the SMSPDSE or SMSPDSE1 address space. See message IGW045I for information provided by this command.

PDSE: Indicates the SMSPDSE address space.
PDSE1: Indicates the SMSPDSE1 address space.

{PDSE|PDSE1},MODULE(modname)

Displays the address and maintenance level of module name (modname) for the SMSPDSE or SMSPDSE1 address space. This command is provided to help users when a SLIP is needed for a particular module. See message IGW046I for information provided by this command.

{PDSE|PDSE1},VSTOR

Indicates the current PDSE 64-bit directory buffer virtual storage utilization.

Start of change The D SMS,PDSE,VSTOR or D SMS,PDSE1,VSTOR command can display the amount of virtual storage page utilization that is larger that the directory storage size which is defined by the PDSE_DIRECTORY_STORAGE or PDSE1_DIRECTORY_STORAGE parameter. The PDSEx_DIRECTORY_STORAGE value defines the above the bar storage that is used for caching PDSE directory pages. The minimum size for this pool is 64 MB; the default size is 2 GB. The defined value is not a hard limit because heavy periods of PDSE processing requires increasing the pool size. Because PDSE does not compress its internal pools, the pool size reflects a high water mark. End of change

{PDSE|PDSE1},HSPSTATS[,DSN(dsname)][,STORCLAS(sc)|UNMANAGED]

Displays the member cache information about SMS-managed PDSE data sets and non-managed PDSE data sets.

HSPSTATS: Displays the member cache information.
DSN(dsname): An HSPSTATS optional parameter that if specified, indicates that the information is for a specific PDSE, using a fully qualified name, or for a list of PDSEs, using a partially qualified name.
STORCLAS(sc): An HSPSTATS optional parameter that limits the report to SMS-managed PDSE data sets under this storage class. STORCLAS and UNMANAGED parameters cannot be used in the same command.
UNMANAGED: An HSPSTATS optional parameter that limits the report to the data sets that are non-managed PDSEs. STORCLAS and UNMANAGED parameters cannot be used in the same command.

Note:

If STORCLAS and UNMANAGED are not specified, the information is for both SMS-managed and non-managed PDSEs.

Example of valid names:

IBMUSER.PDSE.DATASET (specific dataset)
IBMUSER.*  (all PDSEs with the high level qualifier of IBMUSER) 
IBMUSER.PDSE.* (all PDSEs starting with IBMUSER.PDSE)

{PDSE|PDSE1},HSPSTATS[,SUMMARY]

Displays a summary report of the member cache information.

SUMMARY: An HSPSTATS optional parameter that displays only a summary report. SUMMARY parameter cannot be used with the other parameters.

{PDSE|PDSE1},HSPSTATS[,MAXDSNS(maxds)]

Displays the member cache information report to a number of data sets.

MAXDSNS(maxds): An HSPSTATS optional parameter that limits the report to a number of data sets. If specified, the report displays up to this number of data sets. The default is the complete report in a scrollable screen. The maximum number allowed is 9999. MAXDSNS can be used with the different variations of DSN, STORCLAS or UNMANAGED parameters.

{PDSE|PDSE1},CONNECTIONS,DSN(dsname)[,VOL(volser)]

Displays the users of a particular PDSE or PDSE1. volser specifies the volume required if the data set is not cataloged.

SEP

Displays the name of the active data separation profile.

SHCDS

Displays the following information about the sharing control data sets. (SHCDS):

Name
Size
Amount of free space for the active and spare SHCDS
Whether the data set is usable

SHUNTED{, SPHERE(sphere)|URID({urid|ALL})}

Displays the entries currently contained in the shunt logs of the systems in the sysplex. Entries are moved to the shunt log when DFSMStvs is unable to finish processing a syncpoint, for example, due to an I/O error. As long as a shunted entry exists, the locks associated with that entry are retained.

Three types of information that can be displayed in response to this command:

When neither the SPHERE nor URID keyword is specified, this command results in a list of systems in the sysplex and the number of units of recovery which that system has shunted
When the SPHERE keyword is specified, this command results in a list of shunted work for the sphere specified for all of the systems in the sysplex
When the URID keyword is specified, this command results in a list of shunted work for the unit of recovery specified for all of the systems in the sysplex. When ALL is specified, this command results in a list of shunted work for all shunted units of recovery for all the systems in the sysplex. To avoid flooding the console, DFSMStvs writes out 255 lines and then issues a WTOR to determine whether or not to continue.

If the error is correctable, the installation might choose to fix the problem and then request that DFSMStvs again attempt processing of the entry by issuing the SHCDS RETRY command. If the data set cannot be restored to a point where it is consistent with the log entry, so that it does not make sense to attempt processing of the log entry again, the installation might choose to discard the log entry by issuing the SHCDS PURGE command.

If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

SHCDS

Displays the following information about the sharing control data sets. (SHCDS):

Name
Size
Amount of free space for the active and spare SHCDS
Whether the data set is usable

SMSVSAM [,ALL]

Displays the status of the SMSVSAM server on this system or all the SMSVSAM servers and lock table connection status.

The D SMS,SMSVSAM command displays system connect and quiesce status for all lock structures connected by the system issuing the command.

The D SMS,SMSVSAM, ALL command summarizes the system connect and quiesce status for all lock structures connected in the sysplex. IGWLOCK00 cannot be quiesced.

SMSVSAM,QUIESCE

Displays the status of all active VSAM record-level sharing (VSAM/RLS) sphere quiesce events on the system that the command is entered. (This is not a SYSPLEX-wide command.)

SMSVSAM,DIAG(CONTENTION) or SMSVSAM,DIAG(C)

Displays the status of latch contention related to SMSVSAM. Use this command when you suspect that VSAM RLS latch contention is causing a hang or deadlock. For more information about diagnosing VSAM RLS latch contention, see z/OS DFSMSdfp Diagnosis.

STATUS

Displays the online or offline status for tape or optical libraries or optical drives.

STORGRP (storgrp) or SG (storgrp) [,LISTVOL]

Displays the status of the storage group for each MVS system or system group in the SMS complex. If LISTVOL is specified, all the volumes in the storage group and their SMS status are displayed. The status of the storage group is displayed for each MVS system or system group in the SMS complex.

To display a drive named ALL, place the name in double parentheses, as STORGRP((ALL)) or SG((ALL)).

STORGRP(ALL) or SG(ALL) [,LISTVOL]

Displays a list of all storage groups in the SMS configuration, indicating by symbols (. + - * Q D) the status of each storage group for each MVS system or system group.

If you specify LISTVOL, the system displays the following information:

A list of volumes in the storage group, giving the status of each volume for each MVS system or system group in the complex.
The device number of the volume on the system or system group at which the command is issued.

If ALL is specified and no storage groups are defined in the active configuration, the system displays this message:

NO STORAGE GROUPS DEFINED IN THE ACTIVE CONFIGURATION

To display a drive named ALL, place the name in double parentheses, as STORGRP((ALL)) or SG((ALL)).

TRACE or T

Displays the SMS trace options in effect at the time the command was issued, followed by the setting of the parameters that are related to SMS volume selection analysis messages. The display indicates whether each trace option is now on or off. See message IGD002I.

TRANVSAM [,ALL]

Displays information about the instance of DFSMStvs on this system, or on all systems in the sysplex when the ALL keyword is specified. The output includes this information:

The activity keypoint (AKP) trigger, which is the number of logging operations between the taking of keypoints
The status of this instance of DFSMStvs (initializing, active, quiescing, quiesced, disabling, disabled)
How DFSMStvs started:
- Cold start
  The log data was not read, and any old data was discarded.
- Warm start
  The log data was read and processed.
DFSMStvs status with respect to resource recovery services (RRS)
The quiesce timeout value
All logs known to this instance of DFSMStvs, including the log of logs if one is in use
The number of active units of recovery
The status of all known logs associated with this TVS instance, if you specify ALLLOGS. Otherwise, only the UNDO and SHUNT logs are returned

If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

URID({urid|ALL})

Displays information about a particular unit of recovery currently active within the sysplex or about all units of recovery currently active on the system on which the command was issued on whose behalf DFSMStvs has performed any work. This parameter does not include information about work that has been shunted because you can use the DISPLAY SMS,SHUNTED command to display that information. This parameter also does not include information about units of recovery that might be in restart processing as a result of an earlier failure. This work is not considered to be currently active because it is not associated with any batch job, and the units of recovery associated with the work will end as soon as commit or backout processing for them can be completed. The output includes this information:

The age of the unit of recovery
The name of the job with which the unit of recovery is associated
The name of the current step within the job
The status of the unit of recovery (in-reset, in-flight, in-prepare, in-commit, in-backout, indoubt)
The user ID associated with the job

If you specify WTOR, the system will issue a WTOR if the display output exceeds 255 lines.

VOLUME or VOL(volume)

For a DASD volume, the system displays detailed status in the pool storage group with respect to the systems or system groups in the complex. The status indication can be NOT DEFINED TO THE SYSTEM, ENABLED, DISABLED, QUIESCED, DISABLED FOR NEW ALLOCATIONS ONLY, or QUIESCED FOR NEW ALLOCATIONS ONLY. The display also gives the device number of the device on which the volume is mounted. This occurs only on the system or system group at which the command is issued.

For an optical volume, the system displays (in message CBR1140I) detailed status from the optical configuration database.

For a system-managed tape volume, the system displays (in message CBR1180I) detailed status from the tape configuration database.

If the specified volume is not system managed, this message is issued:

COMMAND REJECTED; VOLUME volume IS NOT DEFINED

To display a volume named ALL, place the name in double parentheses, as VOLUME((ALL)) or VOL((ALL)).

VOLSELMSG

Displays the setting of the parameters that are related to SMS volume selection analysis messages, followed by the setting of parameters that are related to SMS trace.

L=a, name, or name-a

Specifies the display area (a), console name (name), or both (name-a) where the display is to appear.

If you omit this operand, the display is presented in the first available display area or the message area of the console through which you enter the command.

Example 1:

Either of the following commands displays the active SMS configuration:

d sms

d sms,a

In this example, three MVS systems are defined to SMS, but only the first two systems have an active Storage Management Subsystem. The third system is either not IPLed or was IPLed without starting SMS.

The response to this command is as follows:

IGD002I 10:13:25 DISPLAY SMS 050 
SCDS = STAGE2.SCDSPLEX.DATA 
ACDS = SYS1.PDSESHR.ACDS 
COMMDS = SYS1.PDSESHR.COMMDS 
DINTERVAL = 150 
REVERIFY = NO 
ACSDEFAULTS = YES 
SYSTEM CONFIGURATION LEVEL INTERVAL SECONDS
SYSTEM1 2005/03/18 10:13:10 15 
SYSTEM2 ---------- -------- N/A 
SYSTEM3 ---------- -------- N/A 
SYSTEM4 ---------- -------- N/A 
SYSTEM5 ---------- -------- N/A 
SYSTEM6 ---------- -------- N/A 
SYSTEM7 ---------- -------- N/A 
SYSTEM8 ---------- -------- N/A

Example 2:

To display the name of the active data separation file, enter:

d sms,sep

In response to this command, the system issues message IGD002I:

IGD002I 09:59:03 DISPLAY SMS 047
ACTIVE DATA SET SEPARATION PROFILE NAME: sep_dsname

If there are no active separation profile, the system issues message IGD002I as:

IGD002I 09:59:03 DISPLAY SMS 047 
NO DATA SET SEPARATION PROFILE IS ACTIVE

Example 3:

To display the status of the storage group sgmixed, enter:

d sms,sg(sgmixed)

The response to this command is as follows:

IGD002I 11:50:52 DISPLAY SMS 448
STORGRP    TYPE                        SYSTEM= 1  3    4    5    6    7    8
SGMIXED    TYPE                                +  .    .    .    .    .    .
**************************** LEGEND *****************************
. THE STORAGE GROUP OR VOLUME IS NOT DEFINED TO THE SYSTEM
+ THE STORAGE GROUP OR VOLUME IS ENABLED
— THE STORAGE GROUP OR VOLUME IS DISABLED
* THE STORAGE GROUP OR VOLUME IS QUIESCED
D THE STORAGE GROUP OR VOLUME IS DISABLED FOR NEW ALLOCATIONS ONLY
Q THE STORAGE GROUP OR VOLUME IS QUIESCED FOR NEW ALLOCATIONS ONLY
SYSTEM 1 = SYSTEM1
IEF196I IEF285I   SYS2.LINKLIB                         KEPT
IEF196I IEF285I   VOL SER NOS= MVSRES.

Example 4:

To display storage group group26, showing the states of all its volumes, enter:

d sms,storgrp(group26),listvol

The output from this command is similar to that of the previous example except that the specific volumes defined to each system are listed.

IGD002I 11:51:34 DISPLAY SMS 453
STORGRP       TYPE                       SYSTEM= 1  7      8
GROUP26       OBJECT                             +  .
LISTVOL IS IGNORED FOR OBJECT, OBJECT BACKUP, AND TAPE STORAGE GROUPS STORGRPNAME
***************************** LEGEND *****************************
. THE STORAGE GROUP OR VOLUME IS NOT DEFINED TO THE SYSTEM
+ THE STORAGE GROUP OR VOLUME IS ENABLED
— THE STORAGE GROUP OR VOLUME IS DISABLED
* THE STORAGE GROUP OR VOLUME IS QUIESCED
D THE STORAGE GROUP OR VOLUME IS DISABLED FOR NEW ALLOCATIONS ONLY
Q THE STORAGE GROUP OR VOLUME IS QUIESCED FOR NEW ALLOCATIONS ONLY
SYSTEM 1 = SYSTEM1

Example 5:

To illustrate the display of trace options, assume that the following two commands have been issued for system MVS3:

SETSMS TRACE(ON),SIZE(128K),TYPE(ERROR),JOBNAME(*)
SETSMS DESELECT(ALL),SELECT(ACSINT,CONFC,MSG),ASID(*)

The first command turns on tracing and sets the trace table size to 128KB. The second command turns off all trace options except for the three options indicated. To display the SMS trace options now in effect, enter:

DISPLAY SMS,TRACE

The output from this command is similar to that shown below. Note that the trace is shown to be on, the trace table size is indicated, and all options are shown to be off except for the three turned on by the SETSMS…,SELECT command.

IGD002I 10:34:39 DISPLAY SMS 053
TRACE = ON SIZE = 128K TYPE = ERROR 
JOBNAME = * ASID = * 
TRACING EVENTS: 
MODULE = ON SMSSJF = ON SMSSSI = ON ACSINT = ON
OPCMD = ON CONFC = ON CDSC = ON CONFS = ON
MSG = ON ERR = ON CONFR = ON CONFA = ON
ACSPRO = ON IDAX = ON DISP = ON CATG = ON
VOLREF = ON SCHEDP = ON SCHEDS = ON 
VTOCL = ONVTOCD = ON VTOCR = ON VTOCC = ON VTOCA = ON
RCD = ON DCF = ON DPN = ON TVR = ON
DSTACK = ON UAFF = ON VOLSELMSG = (OFF,0) TYPE = ERROR JOBNAME = *
ASID = * STEPNAME = * 
DSNAME = *

Example 6:

To display the SMS options now in effect, enter:

12.16.35          d sms,options

The output from this command is similar to the following output.

IGD002I 09:28:44 DISPLAY SMS 133                    
ACDS     = SYS1.PDSESHR.ACDS                        
COMMDS   = SYS1.PDSESHR.COMMDS                      
ACDS LEVEL = z/OS V2.1                              
SMS PARMLIB MEMBER NAME = IGDSMSZV                  
INTERVAL = 15           DINTERVAL = 150             
SMF_TIME = YES          CACHETIME = 3600            
CF_TIME = 3600          PDSE_RESTARTABLE_AS = YES   
PDSE_BMFTIME = 3600     PDSE1_BMFTIME = 3600        
PDSE_LRUTIME = 60       PDSE1_LRUTIME = 60          
PDSE_LRUCYCLES = 15    PDSE1_LRUCYCLES = 15         
LOCAL_DEADLOCK = 15     GLOBAL_DEADLOCK = 4         
REVERIFY = NO           DSNTYPE = LIBRARY           
ACSDEFAULTS = YES       PDSESHARING = EXTENDED      
OVRD_EXPDT = NO         SYSTEMS = 8                 
PDSE_HSP_SIZE = 8MB   PDSE1_HSP_SIZE = 64MB         
USE_RESOWNER = YES      RLS_MAX_POOL_SIZE = 100MB   
RLSINIT = YES           RLSTMOUT = 500                    
COMPRESS = GENERIC      LOG_OF_LOGS = IGWTVS1.LOG.OF.LOGS 
QTIMEOUT = 400          TVSNAME = 001                     
AKP = 200              TV_START_TYPE = WARM               
MAXLOCKS = (100,50)                                       
CICSVR_INIT = NO        CICSVR_DSNAME_PREFIX = DWW.       
CICSVR_RCDS_PREFIX = DWW                                  
CICSVR_GRPNAME_SUFFIX = PROD                              
CICSVR_ZZVALUE_PARM =                                     
CICSVR_UNDOLOG_CONTROL =                                  
CICSVR_UNDOLOG_PREFIX = DWW                               
CICSVR_BACKOUT_CONTROL =                                  
CICSVR_GENERAL_CONTROL =                                  
IGD002I 09:28:44 DISPLAY SMS                              
Rls_MaxCfFeatureLevel = A                                 
RlsAboveThebarMaxPoolSize = 1000  RlsFixedPoolSize = 0    
PDSE_MONITOR = (YES,0,0) PDSE1_MONITOR = (YES,0,0)              
PDSE_DIRECTORY_STORAGE = 2000M PDSE1_DIRECTORY_STORAGE = 2000M  
PDSE_BUFFER_BEYOND_CLOSE = YES  PDSE1_BUFFER_BEYOND_CLOSE = YES 
GDS_RECLAIM = YES       DSSTIMEOUT = 0                          
BLOCKTOKENSIZE = NOREQUIRE       FAST_VOLSEL = OFF              
USEEAV = YES            BREAKPOINTVALUE = 10                    
OAMPROC =               SUPPRESS_DRMSGS = NO                    
OAMTASK =           PDSE_SYSEVENT_DONTSWAP = NO                 
DB2SSID = DBG1           SAM_USE_HPF = YES                      
CA_RECLAIM = DATACLAS                                           
PS_EXT_VERSION = 1                                              
IGD002I 09:28:44 DISPLAY SMS                                    
TRACE    = ON     SIZE = 128K     TYPE = ERROR                  
  JOBNAME = *    ASID = *                                       
  TRACING EVENTS:                                               
    MODULE = ON   SMSSJF = ON   SMSSSI = ON   ACSINT = ON       
    OPCMD  = ON   CONFC  = ON   CDSC   = ON   CONFS  = ON
    MSG    = ON   ERR    = ON   CONFR  = ON   CONFA  = ON
    ACSPRO = ON   IDAX   = ON   DISP   = ON   CATG   = ON
    VOLREF = ON   SCHEDP = ON   SCHEDS = ON   VTOCL  = ON
    VTOCD  = ON   VTOCR  = ON   VTOCC  = ON   VTOCA  = ON
    RCD    = ON   DCF    = ON   DPN    = ON   TVR    = ON
    DSTACK = ON   UAFF   = ON   DEBUG  = ON              
VOLSELMSG = (OFF,0)    TYPE = ERROR    JOBNAME = *       
    ASID = *  STEPNAME = *                               
    DSNAME = *

Example 7:

The DISPLAY SMS,TRANVSAM command displays information about the status of DFSMStvs.

If DFSMStvs is not active, this results in:

IGW800I  DFSMS VSAMRLS REQUEST TO DISPLAY TRANSACTIONAL VSAM INFORMATION
IS REJECTED:  TRANSACTIONAL VSAM IS NOT ACTIVE ON THIS SYSTEM

If DFSMStvs is active, this command results in the following output:

D SMS,TRANVSAM                                                       
IEE932I 774                                                          
IGW800I 13.33.01 DISPLAY SMS,TRANSACTIONAL VSAM                      
DISPLAY SMS,TRANSACTIONAL VSAM - SERVER STATUS                       
 System   TVSNAME  State   Rrs    #Urs    Start    AKP    QtimeOut   
 -------- -------- ------ ----- -------- --------- -------- -------- 
 SYSTEM1  IGWTV001 ACTIVE REG         1 WARM/WARM     200     400    
DISPLAY SMS,TRANSACTIONAL VSAM - LOGSTREAM STATUS                    
 LogStreamName            State     Type      Connect Status         
 -------------------------- ---------- ---------- --------------     
 IGWTV001.IGWLOG.SYSLOG    Enabled    UnDoLog    Connected           
 IGWTV001.IGWSHUNT.SHUNTLOG Enabled    ShuntLog   Connected          
 IGWTVS1.LOG.OF.LOGS       Enabled    LogOfLogs  Connected           
 IGWTVS.FR.LOG001          Enabled    FrLog     Connected

Example 8:

To display information about DFSMStvs, enter this command:

D SMS,TRANVSAM,ALL

The output from this command

D SMS,TRANVSAM,ALL                                                   
IEE932I 777                                                          
IGW800I 13.33.12 DISPLAY SMS,TRANSACTIONAL VSAM,ALL                  
DISPLAY SMS,TRANSACTIONAL VSAM,ALL - SERVER STATUS                   
 System   TVSNAME  State   Rrs    #Urs    Start    AKP    QtimeOut   
 -------- -------- ------ ----- -------- --------- -------- --------
 SYSTEM1  IGWTV001 ACTIVE REG         1 WARM/WARM     200     400   
 SYSTEM2  IGWTV002 ACTIVE REG         0 WARM/WARM     200     400   
DISPLAY SMS,TRANSACTIONAL VSAM,ALL LOGSTREAM STATUS                 
LogStreamName:  IGWTV001.IGWLOG.SYSLOG                              
 System    TVSNAME        State     Type      Connect Status        
 --------   --------     ------------ ---------- --------------     
 SYSTEM1   IGWTV001        Enabled    UnDoLog    Connected          
LogStreamName:  IGWTV001.IGWSHUNT.SHUNTLOG                          
 System    TVSNAME        State     Type      Connect Status        
 --------   --------     ------------ ---------- --------------     
 SYSTEM1   IGWTV001        Enabled    ShuntLog   Connected          
LogStreamName:  IGWTVS1.LOG.OF.LOGS                                 
 System    TVSNAME        State     Type      Connect Status        
 --------   --------     ------------ ---------- --------------     
 SYSTEM1   IGWTV001        Enabled    LogOfLogs  Connected          
 SYSTEM2   IGWTV002        Enabled    LogOfLogs  Connected          
LogStreamName:  IGWTV002.IGWLOG.SYSLOG                              
 System    TVSNAME        State     Type      Connect Status        
 --------   --------     ------------ ---------- -------------- 
 SYSTEM2   IGWTV002        Enabled    UnDoLog    Connected      
LogStreamName:  IGWTV002.IGWSHUNT.SHUNTLOG                      
 System    TVSNAME        State     Type      Connect Status    
 --------   --------     ------------ ---------- -------------- 
 SYSTEM2   IGWTV002        Enabled    ShuntLog   Connected      
LogStreamName:  IGWTVS.FR.LOG001                                
 System    TVSNAME        State     Type      Connect Status    
 --------   --------     ------------ ---------- -------------- 
 SYSTEM1   IGWTV001        Enabled    FrLog     Connected

Example 9:

The DISPLAY SMS,JOB command displays information about the status of a job.

If the job is using DFSMStvs services, this command results in the following output:

D SMS,JOB(TVS3O601)                                                    
IEE932I 780                                                            
IGW801I 13.33.27 DISPLAY SMS,JOB                                       
TRANSACTIONAL VSAM Job Status On System: SYSTEM1                       
JobName  StepName Urid                             Ur Status  # Locks  
-------- -------- -------------------------------- ---------- -------- 
TVS3O601 STEP04   B4E070267EAFD0000000000301010000 IN_FLIGHT       20

Example 10:

The DISPLAY SMS,UR command displays information about a particular unit of recovery on whose behalf DFSMStvs has performed any work.

If the unit of recovery is not active, this command results in the following output:

IGW802I  DFSMS REQUEST TO DISPLAY ACTIVE TRANSACTIONAL VSAM UR(s)
WAS REJECTED,  SPECIFIED URID(s) ARE NOT ACTIVE         
ON ANY TRANSACTIONAL VSAM INSTANCE IN THE SYSPLEX.

If the UR is currently active, this command results in the following output:

D SMS,URID(ALL)                                                       
IEE932I 783                                                           
IGW802I 13.33.39 DISPLAY SMS,URID                                     
TRANSACTIONAL VSAM UrId Status For System: SYSTEM1                    
Urid                          Ur Status  JobName  StepName # Locks    
-------------------------------- ---------- -------- -------- --------
B4E070267EAFD0000000000301010000 InFlight   TVS3O601 STEP04        20

Example 11:

Use the DISPLAY SMS,SHUNTED command to display information about URs currently in the DFSMStvs shunt log.

If there is currently no shunted work, the results are as follows:

IGW803I  09.50.47 DISPLAY SMS,UR (Summary Data)            
SysName   # Urid(s) SysName   # Urid(s) SysName   # Urid(s)
--------  --------  --------  --------  --------  -------- 
SYSTEM1         0  --------        0  --------        0

If there are shunted URs,the results are as follows:

IGW803I  09.50.47 DISPLAY SMS,UR (Summary Data)            
SysName   # Urid(s) SysName   # Urid(s) SysName   # Urid(s)
--------  --------  --------  --------  --------  -------- 
SYSTEM1   urid     -------         0  --------        0

Example 12:

Use the DISPLAY SMS,LOG command to display information about the log streams that DFSMStvs is using.

If the log stream is not currently in use by DFSMStvs, this command results in the following output:

IGW804I DFSMS REQUEST TO DISPLAY              
TRANSACTIONAL VSAM LOG STREAM:  logstream  WAS REJECTED.
                                              
LOG STREAM NOT KNOWN TO DFSMS.

If the log stream is currently in use, this command results in the following output:

D SMS,LOG(IGWTVS.FR.LOG001)                                          
IEE932I 789                                                          
IGW804I 13.34.10 DISPLAY SMS,LOG                                     
DISPLAY SMS,LOG     - LOG STREAM STATUS                              
  Name: IGWTVS.FR.LOG001          State: Enabled     Type: FrdRecovr 
System   TVSNAME  JobName  Urid of Oldest Log Block                  
  -------- -------- -------- --------------------------------        
SYSTEM1  IGWTV001 TVS3O601 B4E070267EAFD0000000000301010000*         
DISPLAY SMS,LOG     - LOG STREAM USAGE                               
  LogStreamName: IGWTVS.FR.LOG001                                    
System   TVSNAME  JobName  JobName  JobName  JobName  JobName        
  -------- -------- -------- -------- -------- -------- --------     
SYSTEM1  IGWTV001 TVS3O601                                           
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX

Example 13:

The DISPLAY SMS,LOG(ALL) command displays information about the log streams that DFSMStvs is using.

D SMS,LOG(ALL)

This command results in the following output:

IEE932I 792             
                                                 
IGW804I 13.34.18 DISPLAY SMS,LOG                                     
DISPLAY SMS,LOG     - LOG STREAM STATUS                              
  Name: IGWTVS.FR.LOG001          State: Enabled     Type: FrdRecovr 
System   TVSNAME  JobName  Urid of Oldest Log Block                  
  -------- -------- -------- --------------------------------        
SYSTEM1  IGWTV001 TVS3O601 B4E070267EAFD0000000000301010000*         
DISPLAY SMS,LOG     - LOG STREAM USAGE                               
  LogStreamName: IGWTVS.FR.LOG001                                    
System   TVSNAME  JobName  JobName  JobName  JobName  JobName        
  -------- -------- -------- -------- -------- -------- --------     
SYSTEM1  IGWTV001 TVS3O601                                           
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                       
DISPLAY SMS,LOG     - LOG STREAM STATUS                              
  Name: IGWTVS1.LOG.OF.LOGS       State: Enabled     Type: LogOfLogs 
System   TVSNAME  JobName  Urid of Oldest Log Block                  
  -------- -------- -------- --------------------------------        
SYSTEM1  IGWTV001 TVS3O601 B4E070267EAFD0000000000301010000*         
DISPLAY SMS,LOG     - LOG STREAM USAGE                               
  LogStreamName: IGWTVS1.LOG.OF.LOGS                                 
System   TVSNAME  JobName  JobName  JobName  JobName  JobName    
  -------- -------- -------- -------- -------- -------- -------- 
SYSTEM1  IGWTV001 TVS3O601                                       
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                   
DISPLAY SMS,LOG     - LOG STREAM STATUS                          
  Name: IGWTV001.IGWLOG.SYSLOG    State: Enabled     Type: UnDo  
System   TVSNAME  JobName  Urid of Oldest Log Block              
  -------- -------- -------- --------------------------------    
SYSTEM1  IGWTV001 TVS3O601 B4E070267EAFD0000000000301010000*     
DISPLAY SMS,LOG     - LOG STREAM USAGE                           
  LogStreamName: IGWTV001.IGWLOG.SYSLOG                          
System   TVSNAME  JobName  JobName  JobName  JobName  JobName    
  -------- -------- -------- -------- -------- -------- -------- 
SYSTEM1  IGWTV001 TVS3O601                                       
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                   
DISPLAY SMS,LOG     - LOG STREAM STATUS                          
  Name: IGWTV001.IGWSHUNT.SHUNTLOG State: Enabled     Type: Shunt
System   TVSNAME  JobName  Urid of Oldest Log Block              
  -------- -------- -------- --------------------------------    
SYSTEM1  IGWTV001         --------- NO ACTIVE UR ---------*      
DISPLAY SMS,LOG     - LOG STREAM USAGE                               
  LogStreamName: IGWTV001.IGWSHUNT.SHUNTLOG                          
System   TVSNAME  JobName  JobName  JobName  JobName  JobName        
  -------- -------- -------- -------- -------- -------- --------     
SYSTEM1  IGWTV001 **NONE**                                           
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                       
                                                                     
DISPLAY SMS,LOG     - LOG STREAM STATUS                              
  Name: IGWTVS1.LOG.OF.LOGS       State: Enabled     Type: LogOfLogs 
System   TVSNAME  JobName  Urid of Oldest Log Block                  
  -------- -------- -------- --------------------------------        
SYSTEM2  IGWTV002         --------- NO ACTIVE UR ---------*          
DISPLAY SMS,LOG     - LOG STREAM USAGE                               
  LogStreamName: IGWTVS1.LOG.OF.LOGS                                 
System   TVSNAME  JobName  JobName  JobName  JobName  JobName        
  -------- -------- -------- -------- -------- -------- --------     
SYSTEM2  IGWTV002 **NONE**                                           
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                       
DISPLAY SMS,LOG     - LOG STREAM STATUS                              
  Name: IGWTV002.IGWLOG.SYSLOG    State: Enabled     Type: UnDo      
System   TVSNAME  JobName  Urid of Oldest Log Block               
  -------- -------- -------- --------------------------------     
SYSTEM2  IGWTV002         --------- NO ACTIVE UR ---------*       
DISPLAY SMS,LOG     - LOG STREAM USAGE                            
  LogStreamName: IGWTV002.IGWLOG.SYSLOG                           
System   TVSNAME  JobName  JobName  JobName  JobName  JobName     
  -------- -------- -------- -------- -------- -------- --------  
*OLDEST URID ACROSS ALL SYSTEMS IN THE SYSPLEX                    
DISPLAY SMS,LOG     - LOG STREAM STATUS                           
  Name: IGWTV002.IGWSHUNT.SHUNTLOG State: Enabled     Type: Shunt 
System   TVSNAME  JobName  Urid of Oldest Log Block               
  -------- -------- -------- --------------------------------     
SYSTEM2  IGWTV002         --------- NO ACTIVE UR ---------*       
DISPLAY SMS,LOG     - LOG STREAM USAGE                            
  LogStreamName: IGWTV002.IGWSHUNT.SHUNTLOG                       
System   TVSNAME  JobName  JobName  JobName  JobName  JobName     
  -------- -------- -------- -------- -------- -------- --------

Example 14:

The DISPLAY SMS,DSNAME command display information about the jobs that have a data set open for DFSMStvs access.

If the data set is not currently open for DFSMStvs access, this command results in the following output:

IGW805I DFSMS REQUEST TO DISPLAY TRANSACTIONAL VSAM USAGE OF  
DATASET: dsname WAS REJECTED.                       
                                                    
DATASET NOT KNOWN TO TRANSACTIONAL VSAM.

If the data set is currently open for DFSMStvs access, this command results in the following output:

D SMS,DSNAME(SYSPLEX.SHCDS.UNDO1.KSDS01)   
IEE932I 795                                
IGW805I 13.34.44 DISPLAY SMS,DSNAME        
DATASET:  SYSPLEX.SHCDS.UNDO1.KSDS01       
IS CURRENTLY IN USE BY THE FOLLOWING JOBS: 
                                           
System Name:  SYSTEM1  TVSNAME:  IGWTV001  
JobNames: TVS3O601

Example 15:

The DISPLAY SMS,OPTIONS command displays the values with which SMS, SMSVSAM, and DFSMStvs are currently operating.

This command results in the following output:

D SMS,OPTIONS                    
IGD002I 13:01:52 DISPLAY SMS 918 
ACDS = SYS1.PDSESHR.ACDS 
COMMDS = SYS1.PDSESHR.COMMDS 
INTERVAL = 15 DINTERVAL = 150 
SMF_TIME = YES CACHETIME = 3600 
CF_TIME = 3600 PDSE_RESTARTABLE_AS = YES 
PDSE_BMFTIME = 3600 PDSE1_BMFTIME = 3600 
PDSE_LRUTIME = 60 PDSE1_LRUTIME = 60 
PDSE_LRUCYCLES = 15 PDSE1_LRUCYCLES = 15
LOCAL_DEADLOCK = 15 GLOBAL_DEADLOCK = 4 
REVERIFY = NO DSNTYPE = LIBRARY 
ACSDEFAULTS = YES PDSESHARING = EXTENDED 
OVRD_EXPDT = NO SYSTEMS = 8 
PDSE_HSP_SIZE = 256MB PDSE1_HSP_SIZE = 256MB 
USE_RESOWNER = YES RLS_MAX_POOL_SIZE = 100MB 
RLSINIT = YES RLSTMOUT = 500 
COMPRESS = GENERIC LOG_OF_LOGS = IGWTVS1.LOG.OF.LOGS 
QTIMEOUT = 400 TVSNAME = 001 
AKP = 200 TV_START_TYPE = WARM 
MAXLOCKS = (100,50) 
CICSVR_INIT = NO CICSVR_DSNAME_PREFIX = DWW. 
CICSVR_RCDS_PREFIX = DWW 
CICSVR_GRPNAME_SUFFIX = PROD 
CICSVR_ZZVALUE_PARM = 
CICSVR_UNDOLOG_CONTROL = 
CICSVR_UNDOLOG_PREFIX = DWW 
CICSVR_BACKOUT_CONTROL = 
CICSVR_GENERAL_CONTROL = 
Rls_MaxCfFeatureLevel = A 
RlsAboveThebarMaxPoolSize = 0 
RlsFixedPoolSize = 0 
PDSE_MONITOR = (YES,0,0) PDSE1_MONITOR = (YES,0,0) 
PDSE_BUFFER_BEYOND_CLOSE = NO
PDSE1_BUFFER_BEYOND_CLOSE = NO
GDS_RECLAIM = YES DSSTIMEOUT = 0 
BLOCKTOKENSIZE = REQUIRE 
IGD002I 13:01:52 DISPLAY SMS 
TRACE = ON SIZE = 128K TYPE = ERROR 
JOBNAME = * ASID = * 
TRACING EVENTS: 
MODULE = ON SMSSJF = ON SMSSSI = ON ACSINT = ON 
OPCMD = ON CONFC = ON CDSC = ON CONFS = ON 
MSG = ON ERR = ON CONFR = ON CONFA = ON 
ACSPRO = ON IDAX = ON DISP = ON CATG = ON 
VOLREF = ON SCHEDP = ON SCHEDS = ON VTOCL = ON 
VTOCD = ON VTOCR = ON VTOCC = ON VTOCA = ON 
RCD = ON DCF = ON DPN = ON TVR = ON 
DSTACK = ON UAFF = ON VOLSELMSG = (OFF,0) TYPE = ERROR JOBNAME = *
ASID = * STEPNAME = * 
DSNAME = *

Example 16:

To display the setting of the parameters that are related to SMS volume selection analysis messages, enter:

D SMS,VOLSELMSG

The response to this command is as follows:

IGD002I 13:58:46 DISPLAY SMS 789
VOLSELMSG = (OFF,0) TYPE = ERROR JOBNAME = *
ASID = * STEPNAME = *
DSNAME = *
TRACE = ON SIZE = 128K TYPE = ERROR
JOBNAME = * ASID = *

Example 17:

The D SMS,SMSVSAM and D SMS,SMSVSAM,ALL commands display lock structure connect status.

To display the system connect and quiesce status for all lock structures connected by the system issuing the command, enter:

D SMS,SMSVSAM

The response to this command is as follows:

IEE932I 847
IGW420I DISPLAY SMS,SMSVSAM
DISPLAY SMS,SMSVSAM - SERVER STATUS
SYSNAME: SYSTEM1 AVAILABLE ASID: 0037 STEP: SmsVsamInitComplete
DISPLAY SMS,SMSVSAM - JOB STATUS
SUBSYSTEMS CONNECTED: 2 BATCH: 2
DISPLAY SMS,SMSVSAM - LOCK TABLE STATUS (IGWLOCK00)
CONNECT STATUS:
SYSNAME: SYSTEM1 ACTIVE RSN: 02010407 RbldNotActive
COMPOSITE STATUS:
ORIGINAL STRUCTURE: NOT VOLATILE FAILURE ISOLATED
NEW STRUCTURE: NOT VOLATILE FAILURE ISOLATED
STRUCTURE STATUS:
SYSNAME: SYSTEM1 Duplex
SECONDARY LOCK TABLE STATUS (TESTLOCK1)
CONNECT STATUS:
SYSNAME: SYSTEM1 ACTIVE RSN: 02010407 RbldNotActive
COMPOSITE STATUS:
ORIGINAL STRUCTURE: NOT VOLATILE FAILURE ISOLATED
NEW STRUCTURE: NOT VOLATILE FAILURE ISOLATED
STRUCTURE STATUS:
SYSNAME: SYSTEM1 NOTCONN

To display the system connect and quiesce status for all lock structures connected in the sysplex, enter:

D SMS,SMSVSAM,ALL

The response to this command is as follows:

DISPLAY SMSVSAM - LOCK TABLE STATUS (TESTLOCK1)
CONNECT STATUS:
SYSNAME: SYSTEM2 ACTIVE RSN: 02010407 RbldNotActive
SYSNAME: SYSTEM1 ACTIVE RSN: 02010407 RbldNotActive
SYSNAME: SYSTEM3 ACTIVE RSN: 02010407 RbldNotActive
SYSNAME: ........ ................. RSN: ........ ................
SYSNAME: ........ ................. RSN: ........ ................
SYSNAME: ........ ................. RSN: ........ ................
SYSNAME: ........ ................. RSN: ........ ................
SYSNAME: ........ ................. RSN: ........ ................
COMPOSITE STATUS:
ORIGINAL STRUCTURE: NOT VOLATILE FAILURE ISOLATED
NEW STRUCTURE: NOT VOLATILE FAILURE ISOLATED
STRUCTURE STATUS:
SYSNAME: SYSTEM2 Duplex Quiesced
SYSNAME: SYSTEM1 Duplex Quiesced
SYSNAME: SYSTEM3 NOTCONN
SYSNAME: ........ ...........
SYSNAME: ........ ...........
SYSNAME: ........ ...........
SYSNAME: ........ ...........
SYSNAME: ........ ..........