PCIe2 4-port (10 Gb + 1 GbE) SR / Copper SFP +RJ45 adapter (FC EN0S, FC EN0T, FC EN0U, and FC EN0V; CCIN 2CC3)

Learn about the specifications and operating system requirements for the feature code (FC) EN0S, FC EN0T, FC EN0U, and FC EN0V adapters.

Overview

The PCIe2 4-port (10 Gb + 1 GbE) SR / Copper SFP +RJ45 adapter is a PCI Express (PCIe) generation 2 (Gen2) x8, short form-factor adapter.
  • The FC EN0S and EN0U are short, full height adapters. FC EN0S is an SR adapter whereas FC EN0U is a Copper SFP adapter.
  • The FC EN0T and EN0V are short, low-profile adapters. FC EN0T is an SR adapter whereas FC EN0V is a Copper SFP adapter.

The adapter provides two 10 Gb SR optical ports and two 1 Gb RJ45 ports. This adapter provides a PCIe 2.0 host bus interface. The adapter supports the Ethernet network interface controller (NIC) function. The adapter is a high-performance adapter that consolidates traffic for networking. The link aggregation and failover features of the adapter make it suitable for critical network applications that require redundancy and high availability.

The four-port adapter provides two 10 Gb small form-factor pluggable (SFP+) optical SR transceiver ports and two 1 Gb RJ45 Ethernet ports. The two 10 Gb SR ports have little connector (LC) duplex-type connectors. The optical transceiver uses shortwave laser optics and is attached with MMF-850nm fiber cabling with LC connectors. See Cables for more information about the optical cables. Each 10 Gb port provides Ethernet connectivity with a nominal data rate of 10 Gbps (gigabits per second). Figure 1 shows the FC EN0S and FC EN0U adapter. Figure 2 shows the FC EN0T and FC EN0V adapter.

Each of the 1 Gb RJ45 port provides Ethernet connectivity at a data rate of 1 Gbps. Each of the 1 Gb ports is connected with a 4-pair, CAT-5 unshielded twisted pair (UTP) cable or with a cable of higher specification, and is supported for distances of up to 100 meters. In addition to 1 Gb (1000 Mb) networks, 100 Mb networks are also supported.

The adapter provides the following features:
  • The adapter is a PCIe2 NIC network convergence adapter.
  • The 10 Gb SR ports can function in the NIC mode.
  • The adapter can be used as the host local area network (LAN) adapter.
  • The adapter supports interrupt moderation to deliver increased performance while significantly reducing processor utilization
  • The adapter supports dual port operation in any PCIe4 or PCIe3 slot
  • The adapter supports auto-negotiation, full-duplex only.
  • The adapter supports multiple media-access control (MAC) per interface.
  • The adapter supports integrated media-access control (MAC) and physical layer (PHY).
  • The adapter supports the following standards for the different ports and functions:
    • IEEE 802.3ae in the 10 GbE ports
    • 802.3ab in the 1 GbE ports
    • Ether II and IEEE 802.3 for encapsulated frames
    • 802.1p for setting up priority levels in tagged VLAN frames
    • 802.1Q for VLAN tagging
    • 802.3x for flow control
    • 802.3ad for load-balancing and failover
    • IEEE 802.3ad and 802.3 for link aggregation
  • The adapter provides message signal interrupts (MSI), MSI-X, and support of legacy pin interrupts.
  • The adapter supports jumbo frames up to 9.6 KB.
  • The adapter supports gigabit EtherChannel (GEC) with the existing software.
  • The adapter supports TCP checksum offload transmission control protocol (TCP), user datagram protocol (UDP), TCP segmentation Offload (TSO) for IPv4 and IPv6.
  • Supports TCP segmentation or large send offload
  • Supports EEPROM-SPI and single EEPROM
Figure 1. PCIe2 4-Port (10 Gb + 1 GbE) SR / Copper SFP +RJ45 adapter (FC EN0S and FC EN0U)
PCIe2 4-port (10 Gb + 1 GbE) SR / Copper SFP +RJ45 adapter (FC EN0S and FC EN0U)
Note: The ports are numbered from top to bottom as T1, T2, and so on for the AIX® and IBM® i operating systems.
Figure 2. PCIe2 LP 4-port (10Gb+1GbE) SR / Copper SFP +RJ45 adapter (FC EN0T and FC EN0V)
PCIe2 LP 4-port (10Gb+1GbE) SRSR / Copper SFP +RJ45 adapter (FC EN0T and FC EN0V)
Note: The ports are numbered from top to bottom of the adapter as T1, T2, and so on for the AIX and IBM i operating systems.

Specifications

Item
Description
Adapter FRU number
00E2715
Regular-height tailstock part number: 00E2863
Low-profile tailstock part number: 00E2720
Wrap plug FRU number
12R9314 (SFP+ SR wrap plug)
10N7405 (1 Gb UTP wrap plug)
Note: These wrap plugs are not included with the card. 12R9314 (FC ECW0) is the only wrap plug that can be purchased from IBM.
I/O bus architecture
PCIe2 x8
Slot requirement
For details about slot priorities, maximums, and placement rules, see PCIe adapter placement rules and slot priorities and select the system you are working on.
Voltage
3.3 V
Form factor
Short, with full-height tailstock
Cables
See Cables for details.

Cables

Use multimode fiber optic cables with shortwave lasers that adhere to the following specifications:
  • OM3 or OM4: Multimode 50/125 micron fiber, 2000 MHz x km bandwidth
  • OM2: Multimode 50/125 micron fiber, 500 MHz x km bandwidth
  • OM1: Multimode 62.5/125 micron fiber, 200 MHz x km bandwidth
Because core sizes are different, OM1 cables only can be connected to other OM1 cables. For best results, OM2 cables must not be connected to OM3 or OM4 cables. However, if an OM2 cable is connected to an OM3 or OM4 cable, the characteristics of the OM2 cable apply to the entire length of the cables. The following table shows the supported distances for the different fiber optic cable types at different link speeds.
Table 1. Supported distances for multimode fiber optic cables
Header Cable Type and Distance
Rate OM1 OM2 OM3
10 Gbps 0.5 meters to 33 meters (1.64 feet to 108.26 feet) 0.5 meters to 82 meters (1.64 feet to 269.02 feet) 0.5 meters to 300 meters (1.64 feet to 984.25 feet)

Operating system or partition requirements

If you are installing a new feature, ensure that you have the software that is required to support the new feature and you must determine any prerequisites that must be met for this feature and the attached devices. For information about operating system and partition requirements, see one of the following topics:
This adapter requires the following drivers:
  • AIX: devices.pciex.e4148a1614109304 for SFP+ optical ports and devices.pciex.e4148a1614109404 for RJ45 ports
  • Linux: bnx2x driver