IEC142I 113-rc,mod,jjj,sss, ddname[-#],dev,ser,dsname(member)
Explanation
The error occurred during processing of an OPEN macro instruction or an OPEN macro instruction with a TYPE=J operand.
- rc
- Associates this message with system completion code 113 and with the return code.
- jjj
- The job name.
- sss
- The step name.
- ddname[-#]
- DDname (followed by a concatenation number if it is part of a concatenation and not the first DD statement in the concatenation).
- dev
- The device number.
- ser
- The volume serial number.
- mod
- The name of the module in which the error occurred.
- dsname(member)
- The data set name. Member name if specified.
- Return Code
- Explanation
- 08
- A JFCB extension block was needed for processing a physical sequential
data set but none was available.
If this error occurs while the system is reading a multivolume tape data set and this abend message is preceded by one of the following messages: IEC709I, IEC710I, IEC711I, or IEC712I, then the next volser to process was provided via the LABAN (Label Anomaly Tape Installation Exit) but either this volume serial could not be enqueued or no JFCB extension is available to add the volume.
- 0C
- OPEN TYPE=J. No JFCB exit exists or the data set is allocated with the insulated DD attribute which is not supported with OPEN TYPE=J.
- 18
- A JFCB extension block was needed for processing a direct or index sequential data set.
- 20
- An end-of-volume condition was encountered while processing a VSAM data set. Multi-volume data sets are not supported when a VSAM data set is opened with a DCB.
- 24
- An OPEN was issued to a multi-volume VSAM data set. Only single-volume VSAM data sets can be opened with a DCB.
- 28
- An attempt was made to open a concatenated VSAM data set with a DCB.
- 2C
- An OPEN was issued for a VSAM data set with a DCB, but the caller was not APF authorized or not in supervisor state.
- 30
- An incorrect JCL disposition was detected for a VSAM data set being opened with a DCB. The only valid VSAM data set dispositions are (OLD,KEEP,KEEP) or (SHR,KEEP,KEEP).
- 34
- An unsupported DCB option was specified for a VSAM data set opened with a DCB. The only valid options are INPUT and UPDAT.
- 38
- An OPEN was issued for a VSAM data set with a DCB, but the format1 DSCB for the data set does not indicate it is a VSAM data set. Ensure that the DSNAME specified on the DD statement is correct and that the program supports opening a VSAM data set with a DCB.
- 3C
- An attempt was made to open a VSAM record level sharing(RLS) control ACB(CTRLACB=YES specified in ACB macro instruction). VSAM RLS Control ACBs are not supported by open.
- 40
- An error occurred during VSAM record level sharing(RLS) processing while attempting to open a VSAM data set with a DCB.
- 44
- An attempt was made to open an EAS eligible data set that has a format 8 DSCB, but the DCBE flag, DCBEEADSCBOK, indicating that the caller understands extended attribute (Format 8/9) DSCBs was not set. This restriction applies only to an EXCP DCB or to a BDAM DCB that has OPTCD=A. The application program did not set EADSCB=OK in the DCBE macro. The data set was created with the EATTR=OPT option. Either change the program to handle 28-bit cylinder numbers and code EADSCB=OK, or use a data set that does not have EATTR=OPT.
- 48
- An attempt was made to open the VTOC on a volume with more than 65,520 cylinders but the DCBE flag, DCBEEADSCBOK, indicating that the caller understands extended attribute (Format 8/9) DSCBs was not set.
- 4C
- A non-VSAM DCB or ACB passed to OPEN is associated with an extended TIOT DD entry (for example: XTIOT). However the DEVSUPxx parmlib member does not include the keyword and value: NON_VSAM_XTIOT=YES.
System action
The task is ended.
Operator response
TRACE=SYS,USR,SLIP
DCB=DIAGNS=TRACE
System programmer response
If the error recurs and the program is not in error, look at the messages in the job log for more information. Search problem reporting data bases for a fix for the problem. If no fix exists, contact the IBM® Support Center. Provide the SYSOUT output for the job.
Programmer response
Correct the error causing the abnormal end as indicated by the return code in the message text. Rerun the job.
Source
DFSMSdfp
Module
IFG0194A, IFG0194D, IFG0194E, IFG0195V, IGC0001I
Routing code
11
Descriptor code
6