IST1321I

Explanation
 This message is part of a group of messages that VTAM® issues in response to a DISPLAY BNCOSMAP,
APPNTOSA, SATOAPPN, or SNSFILTR command. Possible message groups follow.
 If the display type is BNCOSMAP, the following message
group is displayed.  IST350I   DISPLAY TYPE = BNCOSMAP
IST1321I  TABLE FOR BNCOSMAP netid
IST1322I  NON-NATIVE     NATIVE
IST1323I  non-native     native
⋮
IST314I   END

If the display type is APPNTOSA, the following message
group is displayed.  IST350I   DISPLAY TYPE = APPNTOSA
IST1321I  TABLE FOR APPNTOSA
IST1431I  APPN COS       SUBAREA COS
IST1323I  appn_cos       subarea_cos      [DEFAULT]
⋮
IST314I   END

If the display type is SATOAPPN, the following message
group is displayed.  IST350I   DISPLAY TYPE = SATOAPPN
IST1321I  TABLE FOR SATOAPPN
IST1514I  SUBAREA COS     APPNCOS
IST1323I  appn_cos       subarea_cos      [DEFAULT]
⋮
IST314I   END

If the display type is SNSFILTR, the following message
group is displayed.  IST350I   DISPLAY TYPE = SNSFILTR
IST1321I  TABLE FOR SAW SENSE FILTER
IST1551I  sense_1 sense_2 sense_3 sense_4 sense_5
⋮
IST314I   END

If the display type is SAMAP, the following message group
is displayed. IST350I   DISPLAY TYPE = SAMAP
IST1321I  TABLE FOR SAMAP
IST1671I  subarea_number MAPSTO subarea_number
⋮
IST314I   END

 IST350I  This message identifies the type of information shown in the
display.
type in this message group is either BNCOSMAP, APPNTOSA, SATOAPPN, SNSFILTR,
or SAMAP. The display contains information about the specified
user-defined tables that are active in VTAM.

 IST1321I  tabletype is either BNCOSMAP, APPNTOSA, SATOAPPN, SAW
SENSE FILTER, or SAMAP. 
netid is displayed when tabletype is BNCOSMAP and
represents the network ID that corresponds to the COS mappings.  netid is the name of the network that was specified
on the NETWORK definition statement. 
DEFAULT_NETID is displayed if no specific value for netid has
been defined.

 IST1322I, IST1431I, IST1514I  This message is a header for the information displayed in message
IST1323I.

 IST1323I
  If tabletype in message IST1321I is BNCOSMAP,
this message shows the corresponding nonnative and native COS names.
 nonnative is the name of the COS that is defined
in an adjacent nonnative subnetwork.
native is the COS name to which the nonnative
COS will map in the topology subnetwork of the issuing node.

If tabletype in message IST1321I is APPNTOSA,
this message shows the corresponding APPN and subarea COS mappings.
 appn_cos is the COS name that is used for
routing through the APPN network.
subarea_cos is the COS name that is used for
routing through the subarea network.

 DEFAULT is displayed if COSDEF=YES is specified on
the MAPSTO entry of the VBUILD definition statement.

 IST1431I  This message is a header for the information displayed in message
IST1323I.

 IST1514I This message is issued in response to a DISPLAY SATOAPPN command. 

 IST1551I sense is a user-specified sense code, used
by VTAM to filter session awareness
data concerning session setup failures for a CNM application.

 IST1671I subarea_number is the subarea number coded
in the SAMAP table. The two subarea numbers represent the two subarea
components in the composite network node (CNN) that are connected
to each other.

System action
 Processing continues.

Operator response
 None.

System programmer response
 None. 

Routing code
 2

Descriptor code
 5