Capability mismatch: A network component detected a capability
mismatch between different resources involved in the same network
function. For example, an SSCP detects that an LU has been assigned
a subarea address too large for one of the other resources involved
in the session initiation to support.
Bytes 2 and 3 following the sense code contains sense-code-specific
information.
- 0000
- A resource encountered during LU-LU session initiation is not
ENA-capable; the session initiation request might be rerouted.
VTAM® Information: When VTAM receives this sense code for
a session initiation, it continues searching through the adjacent
SSCP table until the destination LU is found or routing is exhausted.
- 0001
- A resource encountered during LU-LU session initiation is not
ENA-capable; the session initiation request should not be rerouted.
- 0002
- An SSCP has requested a "pre-ENA compatible" SLU address
for an SLU that already has an ENA address.
- 0003
- The gateway node selected by the gateway SSCP from the gateway
node list is not ENA-capable when an ENA-capable gateway node is required.
Another gateway node might be tried.
VTAM Information: When VTAM receives this sense code for a session
initiation, it continues searching through the adjacent SSCP table
until the destination LU is found or routing is exhausted.
- 0004
- During a dynamic path update, the SSCP detected that the update
contained a path with an explicit route (ER) number greater than seven
and the target node did not have extended subarea addressing capabilities.
Therefore, the dynamic path update information for this destination
subarea is not being sent to the target node.
- 0005
- The session could not be established because a specified extended
subarea address exceeded that allowed at a node along
the selected session setup path. The gateway SSCP doing
gateway node selection might try the session setup again by selecting
another gateway node having a larger subarea address
limit in the network containing the DLU.
VTAM hint: This sense code
is issued when there are incompatible ESA capabilities
along the session setup path. The DLU direction subarea
address is greater than the OLU direction capabilities.
- 0006
- The session could not be established because a specified extended
subarea address exceeded that allowed at a node along
the selected session setup path. The gateway SSCP doing
gateway node selection may try the session setup again by selecting
another gateway node that uses a smaller subarea address
in the network containing the DLU.
VTAM hint: This sense code is issued when
there are incompatible ESA capabilities along the
session setup path. The OLU direction subarea address
is greater than the DLU direction capabilities.
- 0007
- During a dynamic path update, the SSCP detected that the update
contained a path definition with a subarea address above 255 and that
the target node did not support extended subarea addressing. Therefore,
the dynamic path update information for this destination subarea is
not being sent to the target node.
- 0008
- The session could not be established because the dependent LU
server detected an incompatibility between its capabilities and those
of its dependent LU requester.
- 0009
- The session could not be established because the dependent LU
requester detected an incompatibility between its capabilities and
those of its dependent LU server.
- 000A
- An attempt was made to establish a connection between a boundary
function that does not support cross-subnetwork connections and a
border node.
- 000B
- The extended border node indicator was set during XID exchange
but both the border node and intersubnetwork extended session services
support indicators were not set in the CP capabilities GDS variable.
- 000C
- There is an APPN subnetwork link mismatch. Two nodes might have
a system definition mismatch or two nodes might already have a non-APPN
subnetwork connection active and one attempts to activate an APPN
subnetwork connection.
VTAM hint: An
attempt was made to activate two or more links between two nodes in
which at least one of the links is defined as an APPN intersubnetwork
link, but not all the links are defined as APPN intersubnetwork links.
Determine what type of links should be defined between the two nodes
in your network. Then modify the NATIVE option on the PU definition
to reflect this.
- 000E
- Virtual-route-based transmission group does not support nonnative
connections.
VTAM Information: VTAM sets this sense code when
a virtual-route-based transmission group connection is requested between
two adjacent nodes connected by a nonnative, Type 2.1 connection.
The request for the VRTG connection will fail. The SSCP-SSCP session
will also fail.
- 000F
- An attempt was made to establish a CP-SVR pipe across a subnetwork
boundary between a dependent LU server and a dependent LU requester
with limited multi-subnetwork support.