MQMONITOR resources

An MQMONITOR resource defines attributes for IBM® MQ message consumers, such as the trigger monitor transaction CKTI. Using an MQMONITOR enables the associated transaction that services an MQ queue to restart automatically when the connection to the IBM MQ queue manager is established.

You can use MQMONITOR resources to process incoming messages on MQ queues including initiation queues. You can have more than one MQMONITOR resource processing incoming messages on an MQ queue.

An installed and started MQMONITOR resource monitors the MQ queue that is either specified in the resource attribute QNAME or supplied to the transaction through the MONDATA attribute.

When you define an MQMONITOR resource for processing incoming messages on an MQ initiation queue, ensure that the TRANSACTION attribute specifies CKTI (the default) or is blank and that the QNAME attribute specifies the name of the MQ initiation queue.

When a user-written MQ monitor program, rather than the default CKTI, is to be used with an MQMONITOR resource, it is the responsibility of the user-written program to get messages directly from application queues and perform the required logic. When you code your program, ensure to follow the guidelines described in Developing and using user-written MQ trigger monitors and MQ message consumers.

In order for CICS® to attempt to automatically start the transaction associated with an MQMONITOR, the MQMONITOR must be installed with attributes AUTOSTART(YES) and STATUS(ENABLED). When the connection between CICS and MQ has been established, CICS will start MQ monitors that have been installed with attributes AUTOSTART(YES) and STATUS(ENABLED) if the user ID associated with the task that set the MQCONN resource to CONNECTED has sufficient authority to start the associated transactions.

MQMONITORs are automatically stopped when CICS disconnects from the IBM MQ queue manager.

If z/OS® Workload Manager Health service is active in the CICS region, MQMONITORs react to the region's health state and might be subject to the setting of the z/OS Workload Manager Health service open status. For details, see Effect of z/OS Workload Manager Health service on MQMONITORs.

Note:

You can install an MQMONITOR only if you have previously installed an MQCONN. See Defining and installing MQMONITOR resources for instructions.
When you define an MQMONITOR, CICS checks for consistency with other resource definitions in the same group or list. For more information, see Checks on definitions of MQMONITOR resources.

Security considerations

User ID for the transaction

If security checking is active (that is, the SEC system initialization parameter is set to YES), the user ID to be associated with the transaction is obtained from the MONUSERID attribute of the MQMONITOR resource.

If security checking is disabled (that is, SEC is set to NO), the user ID to be associated with the MQ monitor transaction is the user ID of the transaction that set the state of the MQMONITOR resource to started.

Security checks performed by CICS when setting the MQ monitor state to started

If security checking is active, when setting the MQ monitor state to started, CICS performs security checks on the user ID of the transaction that attempts to set the MQ monitor state to started, as follows:

Note: In the case of setting the MQ monitor state through a CICSPlex® SM API interface such as the CICS Explorer®, the user ID to be associated with the MQ monitor transaction is either the region user ID or the PLTPIUSR user ID (if specified).

CICS verifies that the user ID is a surrogate of the user ID defined in MONUSERID.
CICS verifies that the user ID is authorized to start transactions associated with the user ID defined in MONUSERID.

DFHMQINI

When you install an MQCONN resource that specifies a value in the INITQNAME attribute, CICS also dynamically creates and installs an MQMONITOR resource with the reserved name of DFHMQINI representing the default initiation queue.

DFHMQINI has the following attributes:

QNAME

Specifies the initiation queue name.

TRANSACTION

CKTI (by default)

MONUSERID

This attribute is obtained as follows:

From the PLTPIUSR system initialization parameter, if available
Otherwise, from the CICS region user ID

USERID

The value is the CICS default user ID.