The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

This is a partitioning configuration problem. The LPARCFG Symbolic FRU will help correct the problem.

If the problem persists, call your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

The partition attempted to IPL prior to the platform fully initializing. Retry the partition IPL after the platform IPL has fully completed and the platform is not in standby mode. If that IPL fails, call your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

This is a partitioning configuration problem. The partition is lacking the necessary resources to IPL.

This error might occur when you shut down a partition that is set to automatically IPL and then turn the managed system off and back on. When the partition automatically IPLs, it uses the resources specified in PHYP NVRAM, and this error occurs when the server does not find the exact resources specified in NVRAM. The solution is to activate the partition by using the partition profile on the HMC. The HMC applies the values in the profile to NVRAM. When the partition IPLs, it uses the resources specified in the profile.

The partition could not IPL at the Timed Power On setting because the IPL setting of the partition was not set to Normal. The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

The partition could not IPL. The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

An operating system MSD IPL was attempted with the IPL side on D-mode. This is not a valid operating system IPL scenario, and the IPL will be halted. This SRC is usually seen when a D-mode SLIC install fails and attempts an MSD.

The partition could not IPL. The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

You are attempting to IPL an operating system that is not supported.

A mainstore dump IPL did not complete due to configuration mismatch. Contact your next level of support.

An attempt to perform a partition dump failed. A partition memory error occurred. The failed memory will no longer be used. The partition dump was terminated. The partition ID is in extended word one as LP=xxx (in decimal format). Re-IPL the partition.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). No alternate (D-mode) IPL IOP was selected. The IPL will attempt to continue, but there may not be enough information to find the correct D-mode load source.

Have the customer configure an alternate IPL IOP for the partition. Then retry the partition IPL.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). No default load source IOP was selected for an A/B-mode IPL. The IPL will attempt to continue, but there may not be enough information to find the correct load source.

Have the customer configure a load source IOP for the partition. Then retry the partition IPL.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The IOA for the load source device needed an IOP, and none was detected. Check your LPAR configuration and make sure the correct slot is specified for the IPL load source. Then retry the partition IPL.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). During the partition IPL, code tried to determine if the device in a slot was an I/O Processor or an I/O Adapter. That check failed. Check your LPAR configuration and make sure that the correct slot is specified for the IPL load source. Then retry the partition IPL. If this does not resolve the problem, perform LICIP15.

A mainstore dump IPL did not complete due to a copy error. Contact your next level of support.

A mainstore dump IPL did not complete due to a copy error. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A slot that was needed for the partition was unavailable. See the Symbolic FRU SLOTUSE for more information on the cause of this error.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The platform LIC for this partition attempted an operation. There was a failure. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A slot that was needed for the partition was either empty or the device in the slot has failed. See the Symbolic FRU SLOTUSE for more information on the cause of this error.

If you have a RAID enablement card (CCIN 5709) on your system, it will disable an embedded SCSI adapter. If that embedded slot is called out in the error, you can safely ignore this error.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The platform LIC for this partition attempted an operation. There was a failure. Contact your next level of support.

A user requested an immediate termination and main store dump of a partition. The partition ID is in extended word one as LP=xxx in decimal format.

IPL did not complete due to a copy error. Contact your next level of support.

The search for a valid load source device was exhausted. The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). Perform LICIP15.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A problem occurred on the path to the load source for the partition.

If present, look in the Serviceable Event View for a B7xx xxxx during the partition's IPL. Correct that error and retry the partition IPL.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

The B2xx xxxx SRC Format is Word 1: B2xx3114, Word 3: Bus, Word 4: Board, Word 5: Card.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). Retry count exceeded. This is logged for each unsuccessful attempt to IPL with a loadsource candidate. If the IPL fails, look for other serviceable errors.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

This is a platform LIC main store utilization problem. The platform LIC could not obtain a segment of main storage within the platform's main store to use for managing the creation of a partition.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An unexpected failure return code was returned when attempting to query the IOA slots that are assigned to an IOP.

Look for B700 69xx errors in the Serviceable Event View and work those errors.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). If word 3 is zero, then this SRC is informational and can be ignored.

Otherwise there is a problem in the platform LIC. A nonzero bus number has no associated bus object.

Look for B700 69xx errors in the Serviceable Event View and work those errors.

If there are no serviceable B700 69xx errors, or if correcting the errors did not correct this problem, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An unknown bus type was detected.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The load source IOP is not owned by the partition. This is a configuration problem in the partition. Have the customer reconfigure the partition to have the intended load source IOP.

If there is not a configuration problem then contact your next level of support.

The IOP in the slot used for the last successful IPL of the operating system was replaced with an I/O Adapter. The IPL will continue by searching for a valid load source device.

Check the LPAR configuration if required, and ensure that the tagged I/O for the partition is correct.

The I/O Adapter in the slot used for the last successful IPL of the operating system was replaced with an I/O Processor. The IPL will continue by searching for a valid load source device.

Check the LPAR configuration if required, and ensure that the tagged I/O for the partition is correct.

The I/O Adapter in the slot used for the last successful IPL of the operating system was removed. The IPL will continue by searching for a valid load source device.

Check the LPAR configuration if required, and ensure that the tagged I/O for the partition is correct.

The I/O Processor in the slot used for the last successful IPL of the operating system was removed. The IPL will continue by searching for a valid load source device.

Check the LPAR configuration if required, and ensure that the tagged I/O for the partition is correct.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

Look for a SRC in the Serviceable Event View logged at the time the partition was performing an IPL.

This error indicates a failure during a search for the load source. There may be a number of these failures prior to finding a good load source. This is normal. If a B2xx3110 error is logged, a B2xx3200 may be posted to the control panel. Work the B2xx3110 error in the Serviceable Event View. If the system IPL hangs at B2xx3200 and you cannot check the SRC history, perform the actions indicated for the B2xx3110 SRC.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

Look for a SRC in the Serviceable Event View logged at the time the partition was performing an IPL.

This error indicates a failure during a search for the load source. It is usual for a number of these failures to occur prior to finding a valid load source. This is normal. If a B2xx3110 error is logged, a B2xx3200 may be posted to the control panel. Work the B2xx3110 error in the Serviceable Event View. If the system IPL hangs at B2xx3200 and you cannot check the SRC history, perform the actions indicated for the B2xx3110 SRC.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There is not enough space to contain the partition main storage dump.

Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a partition main storage dump problem. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There is not enough space to contain the partition main storage dump. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was an error reading the partition's main storage dump from the partition's load source into main storage.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A partition main storage dump has occurred but cannot be written to the load source device because a valid dump already exists.

Use the Main Storage Dump Manager to rename or copy the current main storage dump.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was an error writing the partition's main storage dump to the partition's load source.

A problem occurred during the IPL of a partition.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

An error occurred when writing the partition's main storage dump to the partition's load source. No service action required.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was an error writing the partition's main storage dump to the partition's load source.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was an error writing the partition's main storage dump to the partition's load source.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was an error writing the partition's main storage dump to the partition's load source.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An error occurred while doing a main storage dump that would have caused another main storage dump.

Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A platform LIC error occurred when the partition's memory initialized. The IPL will not continue.

Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The partition's LID failed to completely load into the partition's mainstore area.

Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

The load source media is corrupted or not valid.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

This is a problem with the load source media being corrupt or not valid.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format).

A failure occurred when allocating memory for an internal object used for LID load operations. Ensure the partition was allocated enough main storage, verify that no memory leaks are present, and then retry the operation.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). Error on load source device.

An error occurred while copying Open Firmware into the partition load area. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An error condition was encountered when communicating with the load source I/O Processor for the partition identified in the xx field of the B2xx SRC.

This informational error indicates a failure resetting the I/O Processor in the preceding B2xx3200 error. This may be normal. If there is a hardware failure there will be a different serviceable event. If the system IPL hangs at B2xx7200 and you cannot check the SRC history, perform the actions indicated for the B2xx3110 SRC.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An internal LIC timeout has occurred. The partition may continue to IPL but it may experience problems while running.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a failure loading the VPD areas of the partition. Possible causes are:

• Corrupted/unsupported load source media
• Insufficient resources allocated to the partition
• Unsupported partition configuration by the operating system

If the problem is due to media, replace the load source media. If the problem is due to insufficient resources, allocate enough resources to the partition. If the problem is due to unsupported partition configuration, correct the partition configuration.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a problem getting a segment of main storage in the platform's main store.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A failure occurred. The IPL is terminated. Ensure that there is enough memory to IPL the partition.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A failure occurred. The IPL is terminated.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A problem occurred on the path to the load source for the partition.

There was an error mapping memory for the partition's IPL. Call your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A problem occurred on the path to the load source for the partition.

There was a failure verifying VPD for the partition's resources during IPL. Call your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a low level partition to partition communication failure.

Partition did not IPL due to platform Licensed Internal Code error.

Contact your next level of support.

Ensure that the console device cables are connected properly. If the cables are already connected properly, replace the cables. Re-IPL the partition. If the problem reoccurs, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). This partition could not stay running and shut itself down.

Work any error logs in the Serviceable Event View. If there are no errors, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a communications problem between this partition's service processor and the platform's service processor.

The platform will need to be re-IPLed before that partition can be used. Call your next level of support.

Internal platform Licensed Internal Code error occurred during partition shutdown or re-IPL.

Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). There was a communications problem between this partition and code that handles resource allocation. Call your next level of support.

Ensure that the console device cables are connected properly. If the cables are already connected properly, replace the cables. Re-IPL the partition. If the problem reoccurs, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). An operation has timed out.

Ignore this error if there are other serviceable errors. Work those error logs for this partition and for the platform from the Serviceable Event View. If there are no errors, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). Partition processors did not start LIC within the timeout window.

Capture a Partition Dump and call your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The partition did not respond to a system request to power off the partition. This partition had a communications problem.

If the partition is an i5/OS partition, capture a Partition Dump. Contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The partition did not respond to a system request to power off the partition. This partition had a communications problem.

If the partition is an i5/OS partition, perform a Partition Dump and contact your next level of support.

For all other partition types, a Partition Dump is not supported. If the system is Hardware Management Console (HMC) or Integrated Virtualization Manager (IVM) controlled, do an immediate partition power off. If the system is not HMC or IVM controlled, perform a Function 8 on the control panel. After the partition has powered off, re-IPL the partition, collect error logs and contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). The code load operation for the partition's IPL timed out.

Work any error logs for this partition in the Serviceable Event View. If there are no errors, contact your next level of support.

The partition ID is characters 3 and 4 of the B2xx reference code in word 1 of the SRC (in hexadecimal format). If characters 3 and 4 are both zero, then the partition ID is in extended word one as LP=xxx (in decimal format). A problem occurred on the path to the load source for the partition.

A timeout occurred during the process of trying to stop a partition from running. Contact your next level of support.

During an IPL, a timeout occurred while waiting for a ready message from the partition.

Look for other errors. Re-IPL the partition to recover.

During an IPL, a timeout occurred while waiting for a response to a message.

Look for other errors. Re-IPL the partition to recover.

During an IPL, a timeout occurred while waiting for a response to a message.

Look for other errors. If this SRC is displayed in the operator panel, then panel function 34 might be used to retry the current IPL while the partition is still in the failed state.

During an IPL, a timeout occurred while waiting for a response to a message.

Look for other errors. If this SRC is displayed in the operator panel, then panel function 34 might be used to retry the current IPL while the partition is still in the failed state.

If this SRC is displayed in the operator panel during a main store dump IPL, then panel function 34 might be used to retry the current main store dump IPL while the partition is still in the failed state.