PCIe3 16 Gb 2-port Fibre Channel adapter (FC EL43, FC EL5B, FC EN0A, and FC EN0B; CCIN 577F)
Learn about the specifications and operating system requirements for the feature code (FC) EL43, EL5B, FC EN0A, and FC EN0B adapter.
Overview
The PCIe3 16 Gb 2-port Fibre Channel adapter is an x8, generation 3 (gen3), PCIe adapter. This adapter is a high-performance x8 short form adapter also referred to as a PCIe Host Bus Adapter (HBA). The adapter provides two ports of 16 Gb Fibre Channel capability using SR optics. Each port can provide up to 16 Gb Fibre Channel functions simultaneously.
The FC EL43 and FC EN0B adapters are short, low-profile adapters and the FC EL5B and FC EN0A are short, regular height adapters.
Each port provides single initiator capability over a fibre link or with NPIV, multiple initiator capability is provided. The ports are SFP+ and include an optical SR transceiver. The ports have little connector-type (LC) and utilize shortwave laser optics. The adapter operates at link speeds of 4, 8 and 16 Gbps and will automatically negotiate to the highest speed possible. LEDs on each port provide information on the status and link speed of the port.
The adapter connects to a Fibre Channel switch at 4 Gb, 8 Gb or 16 Gb. It can directly attach to a device without a switch at 16 Gb. Attachment without a switch is not supported at 4 Gb or 8 Gb.
N_Port ID Virtualization (NPIV) capability is supported through VIOS.
- The adapter is compliant with the PCIe base and Card Electromechanical (CEM) 2.0 specifications
with the following characteristics:
- Provides an x8 lane link interface at 14.025 Gbps, 8.5 Gbps, or 4.25 Gbps (automatic negotiation with system)
- Provides support for one Virtual Channel (VC0) and one Traffic Class (TC0)
- Provides configuration and I/O memory read and write, completion, and messaging capabilities
- Provides support for 64-bit addressing
- Provides error correction code (ECC) and error protection functions
- Provides link cyclic redundancy check (CRC) on all PCIe packets and message information
- Provides a large payload size of 2048 bytes for read and write functions
- Provides a large read request size of 4096 bytes
- The adapter is compatible with 4, 8, and 16 Gb Fibre Channel interface with the following
characteristics:
- Provides for automatic negotiation between 4 Gb, 8 Gb, or 16 Gb link attachments
- Provides support for the following Fibre Channel topologies: point-to-point (16Gb only) and fabric
- Provides support for Fibre Channel class 3
- Provides a maximum Fibre Channel throughput that is achieved by using full duplex hardware support
- The adapter provides an end-to-end data path parity and CRC protection, including internal data path random-access memory (RAM)
- Provides architectural support for multiple upper layer protocols
- Provides comprehensive virtualization capabilities with support for N_Port ID Virtualization (NPIV) and virtual fabric (VF)
- Provides support for message signaled interrupts extended (MSI-X)
- Provides support for 255 VFs and 1024 MSi-X
- Provides an internal, high-speed static random-access memory (SRAM) memory
- Provides ECC protection of local memory that includes single-bit correction and double-bit protection
- Provides an embedded shortwave optical connection with diagnostics capability
- Provides support for an on-board context management by firmware:
- Up to 8192 FC port logins
- I/O multiplexing down to the Fibre Channel frame level
- Provides data buffers capable of supporting 64+ buffer-to-buffer (BB) credits per port for shortwave applications
- Provides link management and recovery that is handled by firmware
- Provides on-board diagnostic capability accessible by an optional connection
- Provides a performance up to 16 Gbps full duplex
The following figures show the adapter.
Specifications
- Item
- Description
- Adapter FRU number
- 00E3496
- Wrap plug FRU number
- 12R9314Note: The wrap plug is included with the card, and can also be purchased from IBM®.
- I/O bus architecture
- PCIe base and CEM 3.0, x8 PCIe bus interface
- Slot requirement
- For details about slot priorities, maximums, and placement rules, see PCIe adapter placement rules and slot priorities and select the system you are working on.
- Voltage
- 3.3 V, 12 V
- Form factor
- Short, MD2
- FC compatibility
- 4, 8, 16 Gb
- Cables
- Cables are the responsibility of the customer. Use multimode fiber optic cables with shortwave
lasers that adhere to the following specifications:
- OM4: Multimode 50/125 micron fiber, 4700 MHz x km bandwidth
- OM3: Multimode 50/125 micron fiber, 2000 MHz x km bandwidth
- OM2: Multimode 50/125 micron fiber, 500 MHz x km bandwidth
- OM1: Multimode 62.5/125 micron fiber, 200 MHz x km bandwidth
Adapter LED states
Green and yellow LEDs can be seen through openings in the mounting bracket of the adapter. Green indicates firmware operation, and yellow signifies port activity. Table 2 summarizes normal LED states. A 1 Hz pause occurs when the LED is off between each group of fast flashes (2, 3 or 4). Observe the LED sequence for several seconds to ensure that you correctly identify the state.
Green LED | Yellow LED | State |
---|---|---|
On | 2 fast flashes | 4 Gbps link rate: normal, link active |
On | 3 fast flashes | 8 Gbps link rate: normal, link active |
On | 4 fast flashes | 16 Gbps link rate: normal, link active |
Power-on-self-test (POST) conditions and results are summarized in Table 3. These states can be used to identify abnormal states or problems.
Green LED | Yellow LED | State |
---|---|---|
Off | Off | Wake-up failure of the adapter board |
Off | On | POST failure of the adapter board |
Off | Slow flash | Wake-up failure monitor |
Off | Fast flash | Failure in post |
Off | Flashing | Postprocessing in progress |
On | Off | Failure while functioning |
On | On | Failure while functioning |
Slow flash | Off | Normal, link down |
Slow flash | On | Not defined |
Slow flash | Slow flash | Offline for download |
Slow flash | Fast flash | Restricted offline mode, waiting for restart |
Slow flash | Flashing | Restricted offline mode, test active |
Fast flash | Off | Debug monitor in restricted mode |
Fast flash | On | Not defined |
Fast flash | Slow flash | Debug monitor in test fixture mode |
Fast flash | Fast flash | Debug monitor in remote debug mode |
Fast flash | Flashing | Not defined |
Operating system or partition requirements
- The latest version of enabling libraries and utilities can be downloaded from the Fix Central website.
- Power Systems Prerequisites website.
- IBM System Storage Interoperation Center (SSIC) website.
- The latest version of the device driver or IBM Power® RAID adapter utilities (iprutils) can be downloaded from the IBM Service and Productivity Tools website.
- For information about important notices for Linux on IBM Power Systems, see the Linux® on IBM website.