PCIe2 LP 2-port 10GbE SR Adapter (FC 5284; CCIN 5287)

Learn about the specifications and operating system requirements for the feature code (FC) 5284 adapters.

Overview

The FC 5284 and FC 5287 are both the same adapter. FC 5284 is a low-profile adapter and the FC 5287 is a full-height adapter.

The PCIe2 LP 2-port 10GbE SR Adapter is a short, low-profile, high-performance, generation-2 PCIe adapter. This adapter provides two 10-Gb Ethernet ports that can be configured to run at 10 gigabits per second (Gbps). Each of the Ethernet ports can be connected by using a little connector (LC) duplex-type connector over a multi-mode fiber (MMF) 850 nm fiber cable up to 300 meters (984.25 feet) in length. The adapter conforms to the IEEE, 802.3ae 10GBASE-SR specification for Ethernet transmission.

For details about slot priorities and placement rules, see PCIe adapter placement rules and slot priorities and select the system you are working on.

Specifications

Item
Description
Adapter FRU number
74Y3242 (Designed to comply with RoHS requirement)
Wrap plug FRU number
12R9314 (SFP+ SR wrap plug)
Note: Wrap plugs are not included with the card and cannot be purchased from IBM®.
I/O bus architecture
PCIe2.0 x8
Slot requirement
One PCIe x8 (low-profile) slot.
Cables
MMF 850 nm fiber cable are connected to LC duplex-type connectors.
Voltage
3.3 V
Form factor
Low-profile
Maximum number
For details about the maximum number of adapters that are supported, see PCIe adapter placement rules and slot priorities and select the system you are working on.
Attributes provided
  • PCIe x8 Generation 2
  • MSI-X and support of legacy pin interrupts
  • 10GBASE-SR short-reach optics
  • IEEE 802.3ae (10 GbE)
  • IEEE 802.1p priority and 802.1Q VLAN tagging
  • IEEE 802.3x flow control
  • Link aggregation, 802.3ad 802.3 compliance
  • IEEE 802.3ad load-balancing and failover
  • Ether II and 802.3 encapsulated frames
  • Multiple MAC addresses per interface
  • Jumbo frames up to 9.6 Kbytes
  • TCP checksum offload for IPv4
  • TCP segmentation Offload (TSO) for IPv4
  • UDP checksum offload for IPv4
  • Receive side scaling and packet steering
  • Line rate packet filtering and attack protection

Figure 1 shows the adapter.

Figure 1. PCIe2 LP 2-port 10GbE SR Adapter
Figure of the PCIe2 LP 2-port 10GbE SR Adapter

Adapter LED states

The LEDs on the adapter provide information about the adapter's operation status. The LEDs are visible through the adapter's mounting bracket. Figure 1 shows the location of the LEDs. Table 1 describes the different LED states and what those states indicate.

Table 1. Adapter LEDs and descriptions
LED Light Description
Activity/link Green Active link
Off No link

The absence of a link can indicate a defective cable, defective connector, or a configuration mismatch.

Flashing Data activity

Operating system or partition requirements

The adapter is supported on the following versions of the operating systems, depending on the system you are using:
  • AIX®
    • AIX 7.1, Technology Level 3, Service Pack 2, or later
    • AIX 6.1, Technology Level 8, Service Pack 3, or later
    • AIX Version 5.3, Technology Level 12, or later
  • Linux
    • Red Hat Enterprise Linux Version 7, or later, with current maintenance updates available from Red Hat.
    • Red Hat Enterprise Linux Version 6, or later
    • SUSE Linux Enterprise Server 11, Service Pack 1, or later, with current maintenance updates available from SUSE.
    • For support details, see the Linux Alert website.
    • The latest version of the device driver or iprutils can be downloaded from the IBM Service and Productivity Tools website.
  • IBM i
    • IBM i Version 7.2 or later
    • IBM i Version 7.1, or later
  • VIOS
    • VIOS support requires VIOS 2.2.0.11 with Fix Pack 24 and Service Pack 1, or later.



Last updated: Thu, June 27, 2019