PCIe2 LP 4-port 1GbE Adapter (FC 5260; CCIN 576F)

Learn about the specifications and operating system requirements for the feature code (FC) 5260 adapters.

Overview

FC 5260 and FC 5899 are both the same adapter with different feature codes. FC 5260 is a low-profile adapter and the FC 5899 is a full-height adapter.

The PCIe2 LP 4-port 1GbE Adapter is a short, low-profile, generation-2 PCIe adapter. This adapter provides four 1-Gb Ethernet ports that can be configured to run at 1000 megabits per second (Mbps) (or 1 gigabit per second (Gbps)), 100 Mbps, or 10 Mbps. The adapter connects to a network that uses unshielded twisted pair (UTP) cable for distances of up to 100 meters (328.08 feet). The adapter supports AIX® Network Installation Management (NIM) boot capability. The adapter conforms to the IEEE 802.3ab 1000Base-T standard. The adapter supports jumbo frames when running at the 1000 Mbps speed.

Each of the Ethernet ports can be connected by using:
  • CAT5e (or later) UTP cables for 1000 Mbps network attachment
  • CAT5 or CAT3 UTP cables for 100 Mbps or 10 Mbps network attachment
The cables are attached to the copper RJ45 connectors. Each port is independent of one another and supports full-duplex or half-duplex. The half-duplex mode does not support a speed of 1000 Mbps.
The adapter provides the following features:
  • Supports interrupt moderation to deliver increased performance while significantly reducing processor utilization
  • Supports dual port operation in almost any PCIe slot, except x1
  • Supports auto-negotiation, full-duplex only
  • Supports integrated media-access control (MAC) and physical layer (PHY)
  • Supports Fast EtherChannel (FEC) with the existing software
  • Supports gigabit EtherChannel (GEC) with the existing software
  • Supports IEEE 802.3ad (Link Aggregation control protocol)
  • Supports IEEE 802.1Q VLANs
  • Supports IEEE 802.3 z, ab, u, x flow control support
  • Supports IEEE 802.1p
  • Supports IEEE 802.3ab for TX
  • Supports TCP checksum offload transmission control protocol (TCP), user datagram protocol (UDP), Internet Protocol (IP) for IPv4 and IPv6
  • Supports TCP segmentation or large send offload
  • Supports EEPROM-SPI and single EEPROM
  • Supports interrupt levels INTA and MSI
  • Hardware certifications FCC B, UL, CE, VCCI, BSMI, CTICK, MIC
  • Network Controller (MAC) Intel 82571EB
  • Compliant with European Union Directive 2002/95/EC on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Specifications

Item
Description
Adapter FRU number
74Y4064 (Designed to comply with RoHS requirement)
Wrap plug
10N7405
Note: Wrap plugs are not included with the card and cannot be purchased from IBM®.
I/O bus architecture
PCIe2.0 x4
Slot requirement
One PCIe x4 (low-profile) slot.
Cables
4-pair, CAT5e, UTP cables are connected to copper RJ45 connectors.
Voltage
3.3 V
Form factor
short, low-profile
Maximum number
For details about the maximum number of adapters that are supported, see PCIe adapter placement rules and slot priorities and select the system you are working on.
Connector information
  • Two RJ-45 ports
  • Two LED adapter status indicators per port, for link activity and speed
Attributes provided
  • PCIe x4, generation-1 or generation-2
  • 4-Port machine access code (MAC)
  • High performance IPV4/IPV6 checksum offload
  • Supports large send and large receive
  • Multiple queues
  • VIOS

The following figure shows the adapter.

Figure 1. Adapter
Figure of the adapter

Adapter LED states

The LEDs on the adapter provide information about the operation status of the adapter. The LEDs are visible through the mounting bracket. Figure 1 shows the location of the LEDs. Table 1 describes the different LED states and what those states indicate.

Table 1. Adapter LEDs and descriptions
LED Light Description
Speed Yellow 10 Mbps or 100 Mbps
Green 1000 Mbps or 1 Gbps
Activity/link Green flashing Active link or data activity
Off No link

The absence of a link can indicate a defective cable, defective connector, or a configuration mismatch.

For details about slot priorities and placement rules, see PCIe adapter placement rules and slot priorities and select the system you are working on.

Operating system or partition requirements

The adapter is supported on the following versions of the operating systems, depending on the system you are using:
  • AIX
    • AIX 7.1, Technology Level 3, Service Pack 2, or later
    • AIX 6.1, Technology Level 8, Service Pack 3, or later
    • AIX Version 5.3, Technology Level 12, or later
  • Linux
    • Red Hat Enterprise Linux Version 7, or later, with current maintenance updates available from Red Hat.
    • Red Hat Enterprise Linux Version 6.4, or later, with current maintenance updates available from Red Hat.
    • SUSE Linux Enterprise Server Version 12, or later
    • SUSE Linux Enterprise Server 11, Service Pack 2, or later, with current maintenance updates available from SUSE.
    • Ubuntu Server 14.04.3, or later
    • For support details, see the Linux Alert website.
    • The latest version of the device driver or iprutils can be downloaded from the IBM Service and Productivity Tools website.
  • IBM i
    • IBM i Version 7.2 or later
    • IBM i Version 7.1, or later
  • VIOS
    • VIOS support requires VIOS 2.2.1.4, or later.
  • PowerKVM
    • IBM PowerKVM 2.1.1, or later
Parent topic: PCIe adapters
Related information:
IBM Prerequisite website
Installing, removing, or replacing PCIe adapters
PCIe adapter placement rules and slot priorities
PCIe adapter information by feature type


Last updated: Thu, June 27, 2019