IBM Power System S914 features
Powerful 1-socket server with up to eight active cores
A 1-socket server with up to eight activated cores and I/O configuration flexibility. It features a fully activated IBM® POWER9™ processor module configuration in a 19-inch rack-mount, 4U (EIA units) form factor with 4-core, 6-core, and 8-core up to 3.8 GHz. Up to 1024 GB of DDR4 memory running at speeds of 2133, 2400 and 2666 Mbps.
Storage backplane options
Provides a base 18 SFF-3 Bays/Dual IOA with Write Cache and 12 SFF-3 Bays/RDX Bays; split feature to 6+6 SFF Bays with ability to add a second SAS Controller; and 12 SFF-3 Bays/RDX Bay/2 EXT PT.
Optional and integrated features
Optional PCIe3 NVMe carrier card with two M.2 module slots as well as expansion capabilities for the EXP24SX SFF Gen2 bay Drawer and hot-swap PCIe Gen4 and Gen3 slots. Integrated capabilities include: service processor; EnergyScale technology; hot-swap and redundant cooling; USB 3.0 ports; two HMC ports; and one system port with RJ45 connector.
PowerVM, which delivers industrial-strength virtualization for AIX and Linux environments on POWER processor-based systems, has been enhanced with a virtualization-oriented performance monitor, and performance statistics are available through the HMC. These performance statistics can be used to understand the workload characteristics and to prepare for capacity planning.
Mobile application platform
Get access to important customer service functions by scanning QR labels placed on the system to provide access to key service functions through a mobile device. When the QR label is scanned, it will go to a landing page specific to that server which contains many of the service functions of interest while physically located at the server. These include things such as installation and repair instructions, service diagrams, and reference code look up.
Memory subsystem RAS
Memory has error detection and correction circuitry so that the failure of any one specific memory module within an ECC can be corrected absent of any other fault. A spare DRAM per rank on each memory port provides for dynamic DRAM device replacement during runtime operation. Dynamic lane sparing on the DMI link allows for repair of a faulty data lane.
Processor availability functions
The POWER9 processor performs processor instruction retry for some transient errors and alternate processor recovery for a number of core-related faults. This significantly reduces exposure to both hard (logic) and soft (transient) errors in the processor core.
The L2 and L3 caches in the POWER9 processor in the memory buffer chip are protected with double-bit detect, single-bit correct error detection code (ECC). In addition, a threshold of correctable errors detected on cache lines can result in the data in the cache lines being purged and the cache lines removed from further operation without requiring a reboot in the PowerVM environment.
Live partition mobility
With Live Partition Mobility, users can migrate an AIX or IBM i partition running on one POWER partition system to another POWER system without disrupting services. The migration transfers the entire system environment, including processor state, memory, attached virtual devices, and connected users. It provides continuous operating system and application availability during planned partition outages for repair of hardware and firmware faults.
The service processor provides the capability to diagnose, check the status of, and sense the operational conditions of a system. It runs on its own power boundary and does not require resources from a system processor to be operational to perform its tasks.
Operating systems: AIX 6.1, 7.1, 7.2; IBM i 7.2, 7.2; VIOS 18.104.22.168 or later; LPAR
The minimum Power S914 initial order must include a processor module, two 16 GB DIMMs, four or two power supplies and line cords, an operating system indicator, a cover set indicator, and a Language Group Specify. Also, it must include one of the storage options and the network options below:
Storage options: For boot from NVMe: One NVMe carrier and one NVMe M.2 Module. / For boot from local SFF-3 HDD/SDD: One storage backplane and one SFF-3 HDD or SDD. / For boot from SAN: Internal HDD or SSD and RAID card are not required if feature 0837 (Boot from SAN) is selected. A Fibre Channel adapter must be ordered if feature 0837 is selected.
Network options: One PCIe2 4-port 1 Gb Ethernet adapter. / One of the supported 10 Gb Ethernet adapters