EZZ0395I statement name ON LINE lineno FAILED BECAUSE reason

Explanation

The command failed for the reason indicated.

In the message text:
statement
The profile statement that failed.
name
The name specified on the profile statement.
lineno
The line number in the profile data set where the statement was found.
reason
The reason can be one of the following:
A CONFIGURATION ERROR HAS OCCURRED
One of the following errors occurred during DELETE PORT/PORTRANGE processing:
  • The port define attributes do not agree with the delete attributes. For example, a PORTRANGE was used to define the port, but a DELETE PORT was used to delete the port.
  • An internal configuration error occurred.
A LINK REFERENCES THE ATMLIS
An ATM LINK statement referenced this ATMLIS.
AN ATMARPSV REFERENCES THE ATMLIS
An ATMARPSV statement referenced this ATMLIS.
A VIPA DEVICE CANNOT BE STOPPED OR STARTED
A VIPA device is started when defined and can never be stopped.
DEVICE HAS A LINK DEFINED
The device has a link defined.
DEVICE IS ACTIVE
The device is active.
INTERFACE IS ACTIVE
The interface is not in a valid state to be deleted. The interface must be deactivated.
INTERFACE IS A DYNAMIC VIPA
The name specified on a DELETE DEVICE, DELETE LINK, or INTERFACE DELETE statement is a dynamic VIPA.
INTERFACE IS DEFINED AS A SOURCE VIPA INTERFACE
The interface is specified on the SOURCEVIPAINTERFACE keyword for another interface and therefore cannot be deleted.
LINK IS ACTIVE
The link is active.
LINK STATE NOT VALID
The device or link is not in a valid state to be deleted.
LINK TYPE NOT VALID
The link type for the specified name is not valid for the statement.
Start of changeTHE ASSOCIATED SMCRV2 RNIC IS ACTIVEEnd of change
Start of changeThe associated SMC-Rv2 RDMA capable network interface controller (RNIC) is active.End of change
THE ATMARPSV IS BUSY
The ATMARPSV cannot be deleted when it is in use.
THE ATMPVC IS USED BY AN ATMARPSV
The ATMPVC cannot be deleted until the ATMARPSV that specifies it is deleted.
THE LINK HAS PVCS DEFINED
An ATMPVC statement has a PVC to this link defined.

System action

TCP/IP continues.

Operator response

None.

System programmer response

See the following based on reason indicated:
A CONFIGURATION ERROR HAS OCCURRED
Determine if the DELETE PORT/PORTRANGE statement is correct:
  • If the statement is incorrect, correct it and use the VARY TCPIP,,OBEYFILE command to delete the PORT/PORTRANGE.
  • If the statement is correct, the problem is because of an internal configuration error. Exception CTRACE records were written at the time of the error. Contact the IBM® Support Center with the CTRACE records and message information.
A LINK REFERENCES THE ATMLIS
The ATM LINK must be deleted before the ATMLIS can be deleted. The VARY TCPIP,,OBEYFILE command can be issued to delete the ATM LINK.
AN ATMARPSV REFERENCES THE ATMLIS
ATMARPSV must be deleted before the ATMLIS can be deleted. The VARY TCPIP,,OBEYFILE command can be issued to delete the ATMARPSV.
A VIPA DEVICE CANNOT BE STOPPED OR STARTED
No action.
DEVICE HAS A LINK DEFINED
The link must be deleted before the device can be deleted. The VARY TCPIP,,OBEYFILE command can be used to delete the link.
DEVICE IS ACTIVE
The device must be stopped before it can be deleted. The VARY TCPIP,,STOP command can be issued to stop the device.
INTERFACE IS A DYNAMIC VIPA
You must use the VIPADELETE statement to delete a dynamic VIPA.
LINK STATE IS NOT VALID
The link is in use. If this message was issued in response to an attempt to delete a link, the link IP address might still be defined. You must delete the link IP address from the HOME list before the link can be deleted. To remove the link IP address from the HOME list, use the VARY TCPIP,,OBEYFILE command with a profile that contains a HOME statement that does not include the home IP address that is associated with the link that you want to delete. If you specify the updated HOME statement and the DELETE LINK statement in the same VARY TCPIP,,OBEYFILE data set, the HOME statement must precede the DELETE LINK statement.
Start of changeTHE ASSOCIATED SMCRV2 RNIC IS ACTIVEEnd of change
Start of changeThe associated SMC-Rv2 RNIC interface must be stopped before the QDIO interface and the RNIC interface can be deleted. Use the VARY TCPIP,,STOP command to stop the RNIC interface. The RNIC interface name associated with this OSA interface is dynamically generated using the PFID that you specified on the OSA INTERFACE statement. The RNIC interface name is in the form EZARIUTpffff, where p is the port number and ffff is the PFID.End of change
THE ATARPSV IS BUSY
No action.
THE ATMPVC IS USED BY AN ATMARPSV
ATMARPSV must be deleted before ATMPVC can be deleted. The VARY TCPIP,,OBEYFILE command can be issued to delete the ATMARPSV.
THE LINK HAS PVCS DEFINED
The PVC must be deleted before the link can be deleted. The VARY TCPIP,,OBEYFILE command can be issued to delete the PVC.

Module

EZACFMS1

Procedure name

ioctlmsg