Command level 2

Table 1. Command Level 2 Action Characters
Action Characters SDSF Actions, or MVS and JES2 Commands Issued Where Valid
A $TO (Set output) H O
C

$C (Cancel)
$CO (Cancel)

See notes 1 and 2.

DA H I JDS O ST LI NO PR PUN RDR SO
H O

C $C JG
CA $C,ARMRESTART DA I ST
CD $C (Cancel, dump). See note 2. DA I ST
CDA $C,D,ARMRESTART DA I ST
CP $C JG
E Erase output descriptors OD
E $E (Restart) DA I ST LI NO PR PUN SO
EC $E (Restart) DA I ST
ES ESH $E (Restart) DA I ST
H $H (Hold) DA I ST
H $H JG
H $TO (Set output) H O
H SSI JDS
O $O (Release). See note 1. JDS ST
O $TO (Release). See note 1. H
OK $TO (Release). See note 1. H
P

$C (Purge)
$CO (Purge)

See notes 1 and 2.

DA H I JDS O ST
H O  
P $C JG
PP $C (Purge protected). See note 2. DA I ST
W $T (Set) DA I JDS ST
Notes:
  1. SDSF uses the subsystem interface (SSI) when you enter a C, O, or P action character on the JDS panel. When all data sets are deleted by use of the C and P action characters on the H panel, SDSF issues $O.
  2. When a TSU job is canceled or purged on the DA, I, or ST panels, SDSF issues the MVS command, C U=userid or C U=userid,DUMP rather than $C; a $C is used to cancel a TSU job on the DA panel. When an active APPC transaction program is canceled or purged on the DA panel, SDSF issues C jobname,A=asid rather than $C.
Table 2. Command Level 2 Overtypeable Fields
Overtypeable Fields MVS and JES2 Commands Issued Where Valid
ADDRESS   JDS OD
AFPPARMS   JDS OD
BUILDING   JDS OD
BURST $TO (set Output) H O
C $TO (Set output). See note. H O JDS
C $T I ST
CC SSI JDS
COLORMAP   JDS OD
COMSETUP   JDS OD
DEPARTMENT   JDS OD
DEST $TO (Set output). See note. H O JDS
FCB $TO (Set output) H O
FLASH $TO (Set output) DA H O
FORMDEF   JDS OD
FORMLEN   JDS OD
FORMS $TO (Set output). See note. H O JDS
INTRAY   OD
IP DESTINATION   OD
ITY   JDS
NAME   JDS OD
NOTIFY   JDS OD
OCOPYCNT   JDS OD
ODISP $TO (Set output) H O
OFFSETXB   JDS OD
OFFSETXF   JDS OD
OFFSETYB   JDS OD
OFFSETYF   JDS OD
OUTBIN   OD
OUTBN   JDS
OVERLAYB   JDS OD
OVERLAYF   JDS OD
PAGEDEF   JDS OD
PORT   JDS
PORTNO   OD
PRTOPTNS   OD
PRTQUEUE   OD
PRMODE $TO (Set Output) H O
PRTDEST $R (Route) I ST
RETAINF   OD
RETAINS   OD
RETRYL   OD
RETRYT   OD
ROOM   JDS OD
TITLE   JDS OD
UCS $TO (Set output) H O
USERDATA   OD
USERDATA1   JDS
USERLIB   JDS OD
WTR $TO (Set Output). See note. H O JDS
Note:

SDSF uses the subsystem interface (SSI) when you overtype fields on the JDS panel.

Parent topic: Action characters and overtypeable fields for each command level