Explanation
RMF™ encountered
an error while trying to read the I/O configuration data set (IOCDS).
A model-dependent return code is included only if IOCDS data is returned
by the service processor.
The possible return codes are:
- 0001
- Data set not found during READ.
- 0002
- Buffer address is not valid.
- 0003
- Permanent I/O error.
- 0005
- Number of records to be read is less than or equal to zero, or
greater than 32,768.
- 0007
- Record format is not valid.
- 0008
- Incorrect length.
- 0009
- Data set open for output.
- 0011
- Number of records for a variable length data set is one.
- 0013
- Displacement of a variable length data set in the ACTIVEFILE table
is not valid.
- 0014
- Character is not valid in data set name during READ.
- 0015
- Character is not valid in data set type during READ.
- 0020
- Character is not valid in data set ID during OPEN process.
- 0024
- Data set mode is not valid during OPEN process.
- 0036
- Disk not accessed during OPEN process.
- 0037
- Failure in non-READ/WRITE services.
- 0100
- Number of records specified in model-dependent parameter is not
valid.
- 0101
- Data set not open.
- 0102
- Data set is not valid in model-dependent parameter.
- 0104
- Function is not valid in model-dependent parameter.
- 0106
- Command not accepted because write sequence is in progress.
- 0107
- Diagnostic IOCDS is active but not valid for reads.
- 0108
- No IOCDS is currently marked active.
- 0112
- End of file, or record number is greater than number of records
in data set.
- 0128
- Data set not found during OPEN process.
- 0130
- IOCDS/IOCS file specified may not be accessed from this CEC side.
- 0132
- IOCDS/IOCS is open for a write by another partition. This is returned
by the LPAR hypervisor.
- 0133
- IOCDS/IOCS is invalid because a partition was reset during a write
operation. The IOCDS/IOCS must be validated by a write sequence. This
is returned by the LPAR hypervisor.
- 0134
- The PR/SM* partition is not authorized to read the IOCDS.
- 01F0
- Function not supported by VM.* Option RMCHINFO not specified for
the MVS™ virtual machine on VM.
For VM/ESA,
specify the RMCHINFO option to get the configuration data in the IOQ
report.
- 0200
- Successful for inactive IOCDS/IOCS.
- 0201
- Successful for active not updated IOCDS/IOCS.
- 0202
- The active IOCDS used for this power on reset has already been
updated. Because it may not reflect the current configuration information, RMF ends further attempts to process
this information.
- 0457
- IOCDS format error. This occurs when RMF is
run under PR/SM™ without the PR/SM support PTF installed.
- FFFF
- Reserved for service call front-end routing module. Incorrect
routing code specified.
System action
RMF cannot
obtain information about the present I/O configuration. The action RMF takes for each report is:
- CHANNEL PATH ACTIVITY
- RMF continues monitoring
but cannot obtain the channel type for the system management facility
(SMF) record or for the written report.
- I/O DEVICE ACTIVITY
- RMF continues monitoring
devices but cannot obtain the logical control unit (LCU) identifier
for the SMF record. The RMF report,
if requested, will not contain the LCU device activity summary; instead,
the device report lists the device numbers in ascending order, and
the LCU field is blank.
- I/O QUEUEING ACTIVITY
- RMF stops monitoring I/O
queuing activity and issues message ERB260I.
System programmer response
Contact your software support personnel.
Source
Resource Measurement Facility™ (RMF)
Routing code
Descriptor code