Error codes
This topic describes the tape library error codes.
Table 1 lists the severity, the SNMP trap ID, and the URC for each error code.
Error code | Description | Severity | SNMP trap ID | URC |
---|---|---|---|---|
0001 |
Cartridge {VOLSER} could not be read. |
Warning |
201 |
C001 |
0002 |
Cartridge {VOLSER} could not be written to. |
Warning |
202 |
C002 |
0003 |
Cartridge {VOLSER} had a read, write, or positioning error. |
Warning |
203 |
NA |
0004 |
Cartridge {VOLSER} had a read, write, or positioning error because of faulty media. |
Warning |
204 |
NA |
0005 |
Cartridge {VOLSER} could not be read from because of faulty media or a faulty drive. |
Warning |
205 |
0xC005 |
0006 |
Cartridge {VOLSER} could not be written to or there was a positioning error because of faulty media or a faulty drive. |
Warning |
206 |
NA |
0007 |
Cartridge {VOLSER} reached its end of life. |
Warning |
207 |
NA |
0008 |
Cartridge {VOLSER} is not suitable for long term data storage. |
Warning |
208 |
NA |
0009 |
A write command failed because cartridge {VOLSER} is write-protected. |
Informational |
209 |
NA |
000A |
A drive unload was attempted while media removal was prevented. |
Informational |
210 |
NA |
000B |
A cleaning tape was loaded into a drive. |
Informational |
211 |
NA |
000C |
Cartridge {VOLSER} is not supported by the drive. |
Informational |
212 |
NA |
000D |
Cartridge {VOLSER} had a mechanical failure. The cartridge was unloaded. |
Warning |
213 |
NA |
000E |
Cartridge {VOLSER} had a mechanical failure. The cartridge was not unloaded. |
Error |
214 |
0xC00E |
000F |
A drive detected the cartridge memory in cartridge {VOLSER} failed. |
Warning |
215 |
NA |
0010 |
Cartridge {VOLSER} was manually removed from a drive with a read or write in process. |
Informational |
216 |
NA |
0011 |
A drive rejected a write attempt to a read-only cartridge {VOLSER}. |
Informational |
217 |
NA |
0012 |
At load time, a drive detected a corrupted directory for cartridge {VOLSER}. |
Warning |
218 |
NA |
0013 |
Cartridge {VOLSER} was nearing its end of life If you encounter this error, perform the following steps from the host:
|
Warning |
219 |
N/A |
0014 |
A drive requested a cleaning. |
Informational |
220 |
NA |
0015 |
A drive requested a routine cleaning. |
Informational |
221 |
NA |
0016 |
A drive detected an expired cleaning cartridge {VOLSER}. |
Informational |
222 |
NA |
0017 |
A drive detected an invalid cleaning cartridge {VOLSER}. |
Warning |
223 |
NA |
0018 |
A drive reported TapeAlert flag 24. |
Informational |
224 |
NA |
0019 |
Drive Fibre channel interface failed. |
Error |
225 |
0xC020 |
001A |
Drive cooling fan failed. |
Error |
226 |
0xC01A |
001B |
Drive power supply failed. |
Error |
227 |
0xC01B |
001C |
A drive reported TapeAlert flag 28. |
Informational |
228 |
NA |
001D |
A drive reported a condition that requires drive diagnostics. |
Warning |
229 |
N/A |
001E |
A drive failed. A drive reset is required. |
Error |
230 |
0xC01E |
001F |
Drive power-on self-tests failed. A drive hard reset is required. |
Error |
231 |
0xC01F |
0020 |
Drive Fibre channel interface failed. |
Error |
232 |
0xC020 |
0021 |
A failure occurred that requires cartridge {VOLSER} to be demounted from the drive and retried. |
Warning |
233 |
NA |
0022 |
A drive firmware update process failed.. |
Informational |
234 |
NA |
0023 |
A drive detected that the humidity is outside the specified operational limits. |
Warning |
235 |
NA |
0024 |
A drive detected that the temperature is outside the specified operational limits. |
Warning |
236 |
NA |
0025 |
Drive power-supply voltages are outside the specified operational limits. |
Error |
237 |
0xC025 |
0026 |
A drive reported a condition that requires drive diagnostics. |
Warning |
238 |
0xC026 |
0027 |
A drive reported a condition that requires drive diagnostics. |
Error |
239 |
0xC027 |
0028 |
A drive reported TapeAlert flag 40. |
Informational |
240 |
NA |
0029 |
A drive reported TapeAlert flag 41. |
Informational |
241 |
NA |
002A |
A drive reported TapeAlert flag 42. |
Informational |
242 |
NA |
002B |
A drive reported TapeAlert flag 43. |
Informational |
243 |
NA |
002C |
A drive reported TapeAlert flag 44. |
Informational |
244 |
NA |
002D |
A drive reported TapeAlert flag 45. |
Informational |
245 |
NA |
002E |
A drive reported TapeAlert flag 46. |
Informational |
246 |
NA |
002F |
A drive reported TapeAlert flag 47. |
Informational |
247 |
NA |
0030 |
A drive reported TapeAlert flag 48. |
Informational |
248 |
NA |
0031 |
Cartridge {VOLSER} was initialized as partitioned or capacity-scaled. |
Informational |
249 |
NA |
0032 |
Cartridge {VOLSER} usage statistics were lost. No action required. |
Informational |
250 |
N/A |
0033 |
At unload time, a drive detected a corrupted directory for cartridge {VOLSER}. |
Warning |
251 |
0xC033 |
0034 |
Cartridge {VOLSER} system area could not be written to. |
Warning |
252 |
0xC034 |
0035 |
Cartridge {VOLSER} system area could not be read. |
Warning |
253 |
0xC035 |
0036 |
Cartridge {VOLSER} does not have a valid start of data. |
Warning |
254 |
0xC036 |
0037 |
Cartridge {VOLSER} could not be loaded and threaded. |
Warning |
255 |
0xC037 |
0038 |
Cartridge {VOLSER} could not be unloaded. |
Error |
256 |
0xC038 |
0039 |
A drive library interface failed. A drive reset is recommended. |
Warning |
257 |
NA |
003A |
A drive performed a self-reset. |
Informational |
258 |
N/A |
003B |
WORM cartridge {VOLSER} has suspect data. |
Warning |
259 |
0xC03B |
003C |
An overwrite command failed for WORM cartridge {VOLSER}. |
Informational |
260 |
NA |
003D |
A drive is configured to require encryption, but encryption is not enabled. |
Warning |
261 |
N/A |
003E |
A drive reported TapeAlert flag 62. |
Informational |
262 |
NA |
003F |
A drive reported TapeAlert flag 63. |
Informational |
263 |
NA |
0040 |
A drive reported TapeAlert flag 64. |
Informational |
264 |
NA |
0200 |
I/O station full. |
Informational |
401 |
NA |
0201 |
The I/O station has been open for five or more minutes. |
Warning |
405 |
NA |
0202 |
An I/O station was opened. |
Informational |
483 |
NA |
0203 |
An I/O station was closed. |
Informational |
484 |
NA |
0210 |
The library ran out of LTO cleaning cartridges. |
Warning |
403 |
NA |
0211 |
The library ran out of 3592 cleaning cartridges. |
Warning |
409 |
NA |
0212 |
LTO cleaning cartridge {VOLSER} expired |
Warning |
406 |
NA |
0213 |
3592 cleaning cartridge {VOLSER} expired |
Warning |
410 |
NA |
0214 |
The library was almost out of licensed LTO storage slots |
Warning |
424 |
NA |
0215 |
The library was almost out of licensed 3592 storage slots |
Warning |
425 |
NA |
0216 |
The library ran out of licensed 3592 storage slots. |
Warning |
426 |
NA |
0217 |
The library ran out of licensed LTO storage slots |
Warning |
427 |
NA |
0218 |
The logical library {LOG_LIB} was almost full |
Warning |
416 |
NA |
0219 |
The logical library {LOG_LIB} was full. |
Warning |
402 |
NA |
021A |
A shuffle operation failed because there were no open slots in the library |
Warning |
407 |
NA |
021C |
The library detected a new unassigned cartridge {VOLSER}. |
Warning |
421 |
NA |
021E |
Cartridge {VOLSER} could not be assigned to logical library {LOG_LIB} because VIO was full. |
Warning |
478 |
NA |
0220 |
A library front door was opened. |
Warning |
16 |
NA |
0221 |
All library doors were closed |
Informational |
422 |
NA |
0230 |
A frame inventory was started. |
Informational |
429 |
NA |
0240 |
Call home started |
Informational |
431 |
NA |
0241 |
Call home failed |
Warning |
415 |
NA |
0242 |
Test call home started |
Informational |
432 |
NA |
0243 |
Required LTO diagnostic cartridge was not found at the required location. |
Informational |
433 |
NA |
0244 |
Required 3592 diagnostic cartridge was not found at the required location. |
Informational |
434 |
NA |
0245 |
Call home finished |
Informational |
432 |
NA |
0247 |
Service logs exported to IBM |
Informational |
482 |
N/A |
0248 |
Library snapshot created. |
Informational |
0 |
NA |
0249 |
System console not responding |
Warning |
495 |
N/A |
0250 |
A cartridge that cannot be encrypted was loaded into a drive that is set to encrypt all cartridges |
Warning |
420 |
NA |
0261 |
During a test, the encryption key manager address failed. |
Warning |
419 |
NA |
0262 |
During a test, the encryption key manager path failed |
Warning |
419 |
NA |
0263 |
During a test, the encryption key manager full path check failed |
Warning |
419 |
NA |
0264 |
The security settings HTTPS certificate will expire in 30 days. |
Warning |
462 |
NA |
0265 |
The security settings HTTPS certificate has expired. |
Error |
463 |
0xA763 |
0280 |
Accessor {ACCESSOR} could not read a barcode. |
Warning |
32 |
0xA4C5 |
0290 |
There is no Media Verification drive for cartridge {VOLSER} generation. |
Warning |
464 |
NA |
0291 |
Media Verification failed for cartridge {VOLSER} |
Error |
465 |
0xA790 |
0292 |
There is only one Media Verification drive assigned to the logical library {LOG_LIB} and it failed |
Error |
466 |
0xA791 |
0293 |
Media Verification passed for cartridge {VOLSER} |
Informational |
0 |
NA |
0295 |
Media Verification drive failed after multiple put errors. |
Error |
467 |
0xA792 |
02B1 |
A move failed because there was not a demount destination available. |
Warning |
407 |
N/A |
02B2 |
A move failed because there was not a Tier0 destage destination available |
Warning |
407 |
N/A |
02B3 |
A move failed because there was not an elastic destage destination available. |
Warning |
407 |
N/A |
02B4 |
A move failed because there was not an import destination available. |
Warning |
407 |
N/A |
02B5 |
A move failed because there was not an ERP destination available. |
Warning |
407 |
N/A |
02C0 |
Cartridge {VOLSER} with an L7 density was unloaded. |
Informational |
0 |
NA |
02C1 |
Cartridge {VOLSER} with an M8 density was unloaded. |
Informational |
0 |
NA |
02D0 |
Accessor {ACCESSOR} could not read cartridge barcode label |
Informational |
491 |
NA |
02D1 |
Cartridge CM Volser changed from {VOLSER} to {VOLSER} |
Informational |
492 |
NA |
0300 |
An LCC was unable to communicate with an air conditioning unit. |
Error |
472 |
N/A |
0302 |
An LCC was unable to communicate with a temperature and humidity sensor |
Error |
474 |
N/A |
0303 |
An air conditioning compressor was off unexpectedly |
Error |
475 |
N/A |
0304 |
An environmental LED state was changed to Red - Do Not Open Door |
Informational |
0 |
N/A |
0305 |
An environmental LED state was changed to Yellow - Use Caution when Opening Door |
Informational |
0 |
N/A |
0306 |
An environmental LED state was changed to Green - OK to Open Door |
Informational |
0 |
N/A |
0307 |
Drives were set to environmental protection mode |
Warning |
476 |
N/A |
0308 |
Ambient environment was out of specification at {TEMPERATURE}°C and {HUMIDITY}% RH. |
Warning |
477 |
N/A |
0310 |
A request to open a door was made |
Informational |
0 |
N/A |
0311 |
Library service was completed |
Informational |
0 |
N/A |
0312 |
Library service exceeded 30 minutes |
Error |
479 |
N/A |
0313 |
Library air conditioning normal operation was resumed |
Informational |
0 |
N/A |
0320 |
Ship preparation started |
Informational |
0 |
N/A |
0321 |
Ship preparation finished successfully |
Informational |
0 |
N/A |
0322 |
Ship preparation failed |
Error |
0 |
N/A |
0700 |
The state of the library changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0701 |
The state of drive {DRIVE} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0702 |
The state of accessor {ACCESSOR} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0703 |
The state of LCC node card {FRAME} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0704 |
The state of ACC node card {ACCESSOR} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0705 |
The state of MDA node card {ACCESSOR} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0706 |
The state of Frame {FRAME} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
0 |
N/A |
0707 |
The state of power supply {SIDE} in frame {FRAME} changed from {OLD_STATE} to {NEW_STATE}. |
Informational |
||
0800 |
A user logged in to the GUI from {IPADDRESS} |
Informational |
440 |
NA |
0801 |
A user failed to login from {IPADDRESS} |
Informational |
441 |
NA |
0802 |
A library setting was changed |
Informational |
443 |
NA |
0803 |
A logical library {LOG_LIB} setting was changed |
Informational |
444 |
NA |
0804 |
A tape drive setting was changed |
Informational |
445 |
NA |
0805 |
A cartridge setting was changed |
Informational |
446 |
NA |
0806 |
Library firmware update started. |
Informational |
447 |
NA |
0807 |
Library firmware update failed |
Informational |
455 |
NA |
0808 |
A corrupted library firmware image was downloaded. |
Informational |
456 |
NA |
0809 |
Drive firmware update failed. |
Informational |
457 |
NA |
080A |
ACC/MDA firmware update finished. |
Informational |
458 |
NA |
080B |
LCC firmware update finished. |
Informational |
458 |
NA |
080C |
Accessor {ACCESSOR} FRU replacement finished. |
Informational |
448 |
NA |
080D |
Drive FRU replacement finished |
Informational |
449 |
NA |
080E |
A drive serial number changed |
Informational |
450 |
NA |
080F |
A drive was reset |
Informational |
451 |
NA |
0810 |
An administrator password was changed |
Informational |
453 |
NA |
0811 |
An SNMP test trap was sent from the GUI |
Informational |
408 |
NA |
0812 |
A user logged out of the GUI from {IPADDRESS} |
Informational |
442 |
NA |
0813 |
Library security settings changed. |
Informational |
20 |
NA |
0814 |
The library was set offline |
Informational |
21 |
NA |
0815 |
A drive was offline |
Informational |
22 |
NA |
0816 |
Accessor {ACCESSOR} MDA card was reset by a user. |
Informational |
452 |
NA |
0817 |
Accessor {ACCESSOR} ACC card was reset by a user. |
Informational |
452 |
NA |
0818 |
An LCC card was reset by user. |
Informational |
452 |
NA |
0819 |
The library was reset by user. |
Informational |
452 |
NA |
081A |
The access recovery button was pressed. |
Informational |
460 |
NA |
081B |
User account locked |
Informational |
461 |
NA |
081C |
A service user logged in to the GUI from {IPADDRESS} |
Informational |
471 |
NA |
081D |
Accessor {ACCESSOR} MDA card was reset. |
Informational |
485 |
NA |
081E |
Accessor {ACCESSOR} ACC card was reset. |
Informational |
485 |
NA |
0820 |
A drive beacon was turned on |
Informational |
487 |
NA |
0821 |
A drive beacon was turned off |
Informational |
488 |
NA |
0822 |
A drive was hard reset |
Informational |
489 |
NA |
0900 |
Calibrate frame with accessor {ACCESSOR} started. |
Informational |
0 |
NA |
0901 |
Calibrate frame with accessor {ACCESSOR} finished. |
Informational |
0 |
NA |
0902 |
Accessor {ACCESSOR} calibrate started. |
Informational |
0 |
NA |
0903 |
Accessor {ACCESSOR} calibrate finished. |
Informational |
0 |
NA |
0904 |
Calibrate I/O with accessor {ACCESSOR} started. |
Informational |
0 |
NA |
0905 |
Calibrate I/O with accessor {ACCESSOR} finished. |
Informational |
0 |
NA |
0906 |
Calibrate drive with accessor {ACCESSOR} started. |
Informational |
0 |
NA |
0907 |
Calibrate drive with accessor {ACCESSOR} finished. |
Informational |
0 |
NA |
090C |
Drive firmware update started. |
Informational |
447 |
NA |
090D |
Drive firmware update finished. |
Informational |
459 |
NA |
090E |
Library firmware update started. |
Informational |
447 |
NA |
090F |
Library firmware update finished. |
Informational |
458 |
NA |
0911 |
Inventory finished. |
Informational |
430 |
NA |
0912 |
Inventory with audit started. |
Informational |
429 |
NA |
0913 |
Inventory with audit finished. |
Informational |
430 |
NA |
0914 |
Library verify started. |
Informational |
0 |
NA |
0915 |
Library verify finished. |
Informational |
0 |
NA |
0916 |
Library diagnostics started. |
Informational |
0 |
NA |
0917 |
Library diagnostics finished. |
Informational |
0 |
NA |
091A |
Drive FRU replacement started. |
Informational |
0 |
NA |
091C |
Drive log download started. |
Informational |
0 |
NA |
091D |
Drive log download finished. |
Informational |
0 |
NA |
091E |
Discover hardware started. |
Informational |
0 |
NA |
091F |
Discover hardware finished. |
Informational |
0 |
NA |
0920 |
VOLSER range update started. |
Informational |
0 |
NA |
0921 |
VOLSER range update finished. |
Informational |
444 |
NA |
0922 |
Accessor {ACCESSOR} FRU replacement started. |
Informational |
448 |
NA |
0924 |
Calibrate library with accessor {ACCESSOR} started. |
Informational |
0 |
NA |
0925 |
Calibrate library with accessor {ACCESSOR} finished. |
Informational |
0 |
NA |
0926 |
Drive FRU replacement started |
Informational |
449 |
NA |
0927 |
Drive FRU replacement finished |
Informational |
449 |
NA |
0928 |
Drive test started. |
Informational |
0 |
NA |
0929 |
Drive test finished. |
Informational |
0 |
NA |
092A |
The library was reset. |
Informational |
0 |
NA |
2000 |
The pause button failed. |
Error |
2 |
NA |
2001 |
The access recovery button failed. |
Error |
2 |
NA |
2002 |
Library pause button was pressed |
Informational |
480 |
NA |
2124 |
More than 8 LCC detected on library string |
Warning |
468 |
NA |
2125 |
LCC card failed over |
Warning |
469 |
NA |
2127 |
An LCC communication with Accessor {ACCESSOR} MDA card timed out. |
Warning |
499 |
N/A |
2128 |
An LCC communication with Accessor {ACCESSOR} ACC card timed out. |
Warning |
500 |
N/A |
2380 |
Accessor {ACCESSOR} ACC card failed. |
Error |
2 |
0xA413 |
2381 |
Accessor {ACCESSOR} ACC card CAN bus 1 failed. |
Error |
2 |
0xA413 |
2382 |
Accessor {ACCESSOR} ACC card CAN bus 2 failed. |
Error |
2 |
0xA413 |
2481 |
Accessor {ACCESSOR} MDA card CAN bus 1 failed. |
Error |
2 |
0xA414 |
2482 |
Accessor {ACCESSOR} MDA card CAN bus 2 failed. |
Error |
2 |
0xA414 |
2484 |
An LCC card was not responding over Ethernet |
Warning |
2 |
0xA427 |
2500 |
FPGA L Frame location was incorrect |
Warning |
481 |
N/A |
3021 |
A library side door was opened. |
Warning |
16 |
NA |
3024 |
A library side door was not detected |
Error |
2 |
0xA43B |
3025 |
The service bay barrier was down when a side door was opened |
Error |
2 |
0xA43C |
3026 |
The service bay barrier was up when a side door was closed |
Error |
2 |
0xA43C |
3081 |
A frame was not found |
Error |
2 |
0xA431 |
3430 |
A 12V DC power supply would not turn on |
Error |
28 |
0xA514 |
34A1 |
A 12V DC power supply was not detected |
Error |
28 |
0xA457 |
3746 |
A drive was miscabled |
Error |
2 |
0xA624 |
3749 |
A BPC-G231-to-BPC cable was not connected correctly. |
Error |
2 |
0xA627 |
3750 |
An ASC to flex track cable was not plugged correctly |
Error |
2 |
0xA628 |
3752 |
An LCC to DSC communication failed |
Warning |
486 |
NA |
3753 |
Library frame count in FPGA does not match configuration |
Error |
505 |
NA |
3822 |
An LCC to drive communication failed |
Warning |
1 |
0xB80A |
3833 |
An LCC card could not get a response from a drive |
Error |
1 |
0xB701 |
3834 |
Communication between an LCC card and a drive failed on Ethernet |
Error |
1 |
0xB702 |
3835 |
An LCC card could not communicate with a drive |
Error |
1 |
0xB703 |
3839 |
A drive or canister type did not match the configuration |
Error |
1 |
0xB707 |
383B |
A drive diagnostic test returned an invalid status |
Error |
1 |
0xB709 |
383C |
More than 128 Drives detected on library string |
Warning |
470 |
NA |
4081 |
Gripper {GRIPPER} did not move. |
Error |
2 |
0xB401 |
4082 |
Gripper {GRIPPER} encountered an unexpected hard stop while extending. |
Error |
2 |
0xB402 |
4083 |
Gripper {GRIPPER} encountered an unexpected hard stop while retracting. |
Error |
2 |
0xB403 |
4084 |
Gripper {GRIPPER} encountered a high current condition while extending. |
Error |
2 |
0xB404 |
4085 |
Gripper {GRIPPER} encountered a high current condition while retracting. |
Error |
2 |
0xB405 |
4086 |
Gripper {GRIPPER} was unable to find a hard stop while extending |
Error |
2 |
0xB406 |
4087 |
Gripper {GRIPPER} was unable to find a hard stop while retracting |
Error |
2 |
0xB407 |
4088 |
Gripper {GRIPPER} was unable to get cartridge {VOLSER} |
Error |
2 |
0xB408 |
4089 |
Gripper {GRIPPER} was unable to put cartridge {VOLSER} |
Error |
2 |
0xB409 |
408A |
Gripper {GRIPPER} lost power. |
Error |
2 |
0xB40A |
408B |
Gripper {GRIPPER} encountered a low current condition while retracting. |
Error |
2 |
0xB40B |
408C |
Gripper {GRIPPER} lost a cartridge. |
Error |
2 |
0xB40C |
408D |
Gripper {GRIPPER} is not aligned properly in the gripper cage. |
Error |
2 |
0xB40D |
4181 |
Gripper {GRIPPER} sensor was blocked when it should not have been. |
Error |
2 |
0xB40E |
4182 |
Gripper {GRIPPER} sensor was not blocked when it should have been. |
Error |
2 |
0xB40F |
4183 |
Gripper {GRIPPER} sensor was in a degraded state. |
Error |
7 |
0xB40E |
4184 |
Gripper {GRIPPER} sensor failed. |
Error |
2 |
0xB40E |
4221 |
Accessor {ACCESSOR} X home sensor was blocked when it should not have been. |
Error |
2 |
0xA47A |
4380 |
Accessor {ACCESSOR} X home sensor was not found during a re-zero. |
Error |
2 |
0xA471 |
4480 |
Accessor {ACCESSOR} Y home sensor was blocked when it should not have been. |
Error |
2 |
0xA480 |
4481 |
Accessor {ACCESSOR} Y home sensor was not found during rezero. |
Error |
2 |
0xA481 |
4580 |
Accessor {ACCESSOR} X motor did not move. |
Error |
2 |
0xA490 |
4581 |
Accessor {ACCESSOR} X motion could not find a hard stop while moving left. |
Error |
2 |
0xA491 |
4582 |
Accessor {ACCESSOR} X motion could not find a hard stop while moving right. |
Error |
2 |
0xA492 |
4583 |
Accessor {ACCESSOR} X motion encountered an unexpected hard stop while moving left. |
Error |
2 |
0xA493 |
4584 |
Accessor {ACCESSOR} X motion encountered an unexpected hard stop while moving right. |
Error |
2 |
0xA494 |
4585 |
Accessor {ACCESSOR} X motion required excessive force to move left. |
Error |
2 |
0xA495 |
4586 |
Accessor {ACCESSOR} X motion required excessive force to move right. |
Error |
2 |
0xA496 |
4587 |
Accessor {ACCESSOR} X motion failed due to loss of 40 V dc. |
Error |
2 |
0xA40A |
4588 |
Accessor {ACCESSOR} X motion motor driver failed. |
Error |
2 |
0xA498 |
4589 |
Accessor {ACCESSOR} X motion position drift occurred. |
Error |
2 |
0xA499 |
4590 |
Accessor {ACCESSOR} X motion accessor rezero completed. |
Informational |
2 |
0xA475 |
4591 |
Accessor {ACCESSOR} rezero completed. |
Informational |
2 |
0xA476 |
4680 |
Accessor {ACCESSOR} Y motor did not move. |
Error |
2 |
0xA4A0 |
4681 |
Accessor {ACCESSOR} Y motion could not find a hard stop while moving up. |
Error |
2 |
0xA4A1 |
4682 |
Accessor {ACCESSOR} Y motion could not find a hard stop while moving down. |
Error |
2 |
0xA4A2 |
4683 |
Accessor {ACCESSOR} Y motion encountered an unexpected hard stop while moving up. |
Error |
2 |
0xA4A3 |
4684 |
Accessor {ACCESSOR} Y motion encountered an unexpected hard stop while moving down. |
Error |
2 |
0xA4A4 |
4685 |
Accessor {ACCESSOR} Y motion required excessive force to move up. |
Error |
2 |
0xA4A5 |
4686 |
Accessor {ACCESSOR} Y motion required excessive force required to move down. |
Error |
2 |
0xA4A6 |
4687 |
Accessor {ACCESSOR} Y motion failed because of a loss of 40V DC power. |
Error |
2 |
0xA40B |
4688 |
Accessor {ACCESSOR} Y motion failed. |
Error |
2 |
0xA4A8 |
4689 |
Accessor {ACCESSOR} Y motion failed because of drift. |
Error |
2 |
0xA4A9 |
4690 |
Accessor {ACCESSOR} Y motion accessor rezero completed. |
Informational |
2 |
0xA485 |
4691 |
Accessor {ACCESSOR} Y motion drift was suspected. |
Informational |
2 |
0xA486 |
4780 |
Accessor {ACCESSOR} pivot motor could not move. |
Error |
2 |
0xA5B0 |
4781 |
Accessor {ACCESSOR} pivot motion could not find a hard stop. |
Error |
2 |
0xA5B1 |
4782 |
Accessor {ACCESSOR} pivot motion could not find a hard stop. |
Error |
2 |
0xA5B2 |
4783 |
Accessor {ACCESSOR} pivot motion encountered an unexpected hard stop. |
Error |
2 |
0xA5B3 |
4784 |
Accessor {ACCESSOR} pivot motion encountered an unexpected hard stop. |
Error |
2 |
0xA5B4 |
4785 |
Accessor {ACCESSOR} pivot motion required excessive force to pivot. |
Error |
2 |
0xA5B5 |
4786 |
Accessor {ACCESSOR} pivot motion required excessive force to pivot. |
Error |
2 |
0xA5B6 |
4787 |
Accessor {ACCESSOR} pivot motion failed because of a power loss. |
Error |
2 |
0xA4B8 |
4840 |
Accessor {ACCESSOR} XY positioning could not be determined. |
Error |
2 |
0xA4B9 |
4880 |
Accessor {ACCESSOR} failover occurred. |
Error |
2 |
0xA4BA |
4890 |
Accessor {ACCESSOR} XY impact was detected |
Error |
2 |
0xA4BB |
4891 |
Accessor {ACCESSOR} detected a cartridge in the accessor or gripper's path. |
Error |
2 |
0xA4BB |
48A0 |
Accessor {ACCESSOR} detected an obstacle in the accessor or gripper's path |
Error |
2 |
0xA4BB |
48B0 |
Accessor {ACCESSOR} re-zero failed. |
Error |
2 |
0xA4BC |
4900 |
The number of cartridges in the library needs to be 4 times the number of frames for multi-frame verification testing |
Error |
0 |
N/A |
4901 |
Multi-frame verification test failed |
Error |
0 |
N/A |
4902 |
Multi-frame verification test completed successfully |
Informational |
0 |
N/A |
4903 |
Multi-frame verification test has started |
Informational |
0 |
N/A |
5B22 |
Accessor {ACCESSOR} barcode scanner cannot be triggered. |
Error |
2 |
0xA4C3 |
5B23 |
Accessor {ACCESSOR} barcode scanner cannot be triggered. |
Error |
2 |
0xA4C4 |
5B24 |
Accessor {ACCESSOR} barcode scanner with invalid VPD was detected. |
Error |
2 |
0xA4C5 |
5B82 |
Accessor {ACCESSOR} barcode scanner loopback test failed. |
Error |
2 |
0xA4C2 |
5B86 |
Accessor {ACCESSOR} could not read a frame barcode label. |
Error |
2 |
0xA4CE |
5B89 |
Accessor {ACCESSOR} could not read an I/O station barcode label. |
Informational |
2 |
0xA4C9 |
5B8A |
Accessor {ACCESSOR} barcode scanner communication failed |
Informational |
490 |
NA |
9080 |
Accessor {ACCESSOR} found an empty source element. |
Error |
24 |
0xA4D0 |
9180 |
Accessor {ACCESSOR} inventory with audit failed |
Error |
2 |
0xA4D5 |
9181 |
Accessor {ACCESSOR} inventory failed |
Error |
2 |
0xA4D5 |
9250 |
Accessor {ACCESSOR} had only one usable gripper for operation. |
Error |
2 |
0xA4D2 |
9251 |
Accessor {ACCESSOR} had no usable grippers for operation. |
Error |
2 |
0xA4D2 |
9480 |
Accessor {ACCESSOR} found a destination element unexpectedly full. |
Error |
24 |
0xA4D1 |
A010 |
Cartridge {VOLSER} was not detected from the previous inventory. |
Error |
24 |
0xA950 |
A012 |
An inventory self-correction started. |
Informational |
24 |
0xA952 |
A080 |
Accessor {ACCESSOR} had no grippers installed. |
Error |
2 |
0xB420 |
A08C |
A drive type that was incompatible with the original drive type was detected. |
Error |
2 |
0xB32C |
B061 |
Could not lock I/O station door |
Error |
17 |
0xB091 |
B062 |
Could not unlock I/O station door |
Error |
17 |
0xB092 |
B063 |
Could not open I/O station door |
Error |
17 |
0xB093 |
B064 |
Could not close I/O station door |
Error |
17 |
0xB094 |
B066 |
A magazine type incompatible with the library was detected in an I/O Station |
Warning |
17 |
N/A |
B220 |
Gripper {GRIPPER} could not get cartridge {VOLSER} from I/O station. |
Error |
17 |
0xB320 |
B221 |
Gripper {GRIPPER} could not put cartridge {VOLSER} in I/O station. |
Error |
17 |
0xB321 |
B382 |
Gripper {GRIPPER} could not get cartridge {VOLSER} from slot. |
Error |
2 |
0xB150 |
B383 |
Gripper {GRIPPER} could not get cartridge {VOLSER} out of slot. |
Error |
2 |
0xB152 |
B384 |
Gripper {GRIPPER} found cartridge {VOLSER} stuck in the slot |
Error |
2 |
0xB153 |
B388 |
Gripper {GRIPPER} could not put cartridge {VOLSER} in slot. |
Error |
2 |
0xB151 |
B480 |
Accessor {ACCESSOR} X or Y motion command exceeded the limits of the library |
Error |
4 |
0xAACA |
B481 |
Accessor {ACCESSOR} asymmetrical motor limits were detected |
Error |
4 |
0xAACB |
B500 |
Accessor {ACCESSOR} calibration failed. |
Error |
2 |
0xB190 |
B580 |
Accessor {ACCESSOR} could not find a column fiducial. |
Error |
2 |
0xB361 |
B581 |
Accessor {ACCESSOR} encountered a column tilt outside the specified operational limits |
Error |
493 |
N/A |
B582 |
Accessor {ACCESSOR} found a column fiducial calibration value is outside the operational limits against stored value |
Warning |
496 |
N/A |
B583 |
Accessor {ACCESSOR} found a column calibration value out of range from adjacent column |
Warning |
498 |
N/A |
B584 |
Accessor {ACCESSOR} encountered a column tilt close to the operational limits. |
Warning |
506 |
N/A |
B681 |
Accessor {ACCESSOR} could not find a drive fiducial. |
Error |
2 |
0xC020 |
B682 |
Accessor {ACCESSOR} found a drive fiducial calibration value is outside the operational limits against stored value |
Warning |
497 |
N/A |
B790 |
Accessor {ACCESSOR} could not find an I/O station fiducial. |
Error |
2 |
0xB370 |
B791 |
Accessor {ACCESSOR} could not find an I/O station fiducial. |
Error |
2 |
0xB170 |
B792 |
Accessor {ACCESSOR} detected an un-calibrated frame. |
Error |
2 |
0xB171 |
B793 |
Accessor {ACCESSOR} encountered an I/O station tilt outside the specified operational limits |
Error |
494 |
N/A |
B891 |
A drive did not release the cartridge. This failure could be caused by a cartridge gate not opening due to a gate mechanical problem. |
Error |
2 |
0xC031 |
B893 |
A drive did not load the cartridge |
Error |
2 |
0xC033 |
CCCA |
A memory allocation or stack error occurred. |
Informational |
4 |
0xACCC |
CCCC |
A library firmware error occurred. |
Informational |
4 |
0xACCC |
CCCF |
X authorization failed. |
Error |
4 |
0xACCF |