Lift Tool for installation of rack mount

Edit online
The Lift Tool (FC EB3Z), wedge plate add-on (FC EB4Z) and roller table add-on (FC EB5Z) are required to install Rack Mount Bundle into the customer's frame. This specific IBM-supplied Lift Tool must be used for rack mount installation; no other lift tools are supported. Review all of the safety information, publications, and warning labels or graphics provided before using the Lift Tool.
Note: The wedge plate add-on is required for the CPC drawer installation and the roller table add-on is required for the PCIe+ I/O drawer installation.

The Lift Tool and add-on equipment is to be used only by the IBM Systems Service Representative (SSR).

This graphic shows the Genielift GL-8 standard base lift tool and wedge plate add-on.

Table 1. Lift Tool specifications
Description Width mm (in) Length mm (in) Height mm (in) Weight kg (lb)
Genielift GL-8
or
Vestil HA-LIFT-R-HP

(Standard Base Tool)

 628.7 mm
(24.75 in)
Operating: 882.7 mm (34.75 in)

Stored: 305 mm (12 in)
Operating: 3060.7 mm (120.5 in)

Stored: 1714.5 mm (67.5 in)
 61.0 kg
(134.5 lb)
Wedge plate add-on

(Required for CPC drawer installation)

 470 mm
(18.5 in)		 800.1 mm
(31.5 in)		 120.7 mm
(4.75 in)		 7.5 kg
(16.5 lb)
Roller table add-on

(Required for PCIe+ I/O drawer installation)

 580 mm
(22.8 in)		 825.5 mm
(32.5 in)		 158.75 mm
(6.25 in)		 16.8 kg
(37 lb)
Figure 1. Lift Tool example, with and without wedge plate add-on
This graphic shows the Lift Tool example, with and without wedge plate add-on.
Figure 2. Lift Tool example, with roller table add-on
This graphic shows the Lift Tool example, with and without wedge plate add-on.

Lift Tool Safety Notices

CAUTION:
Regarding IBM provided and/or Client site owned VENDOR LIFT TOOL:
  • Operation of LIFT TOOL by authorized personnel only.
  • LIFT TOOL intended for use to assist, lift, install, remove units (load) up into rack elevations. It is not to be used loaded transporting over major ramps nor as a replacement for such designated tools like pallet jacks, walkies, fork trucks and such related relocation practices. When this is not practicable, specially trained persons or services must be used (for instance, riggers or movers).
  • Read and completely understand the contents of LIFT TOOL operator's manual before using. Failure to read, understand, obey safety rules, and follow instructions may result in property damage and/or personal injury. If there are questions, contact the vendor's service and support. Local paper manual must remain with machine in provided storage sleeve area. Latest revision manual available on vendor's web site.
  • Test verify stabilizer brake function before each use. Do not over-force moving or rolling the LIFT TOOL with stabilizer brake engaged.
  • Do not raise, lower or slide platform load shelf unless stabilizer (brake pedal jack) is fully engaged. Keep stabilizer brake engaged when not in use or motion.
  • Do not move LIFT TOOL while platform is raised, except for minor positioning.
  • Do not exceed rated load capacity. See LOAD CAPACITY CHART regarding maximum loads at center versus edge of extended platform.
  • Only raise load if properly centered on platform. Do not place more than 200 lb (91 kg) on edge of sliding platform shelf also considering the load's center of mass/gravity (CoG).
  • Do not corner load the platforms, tilt riser, angled unit install wedge or other such accessory options. Secure such platforms -- riser tilt, wedge, etc options to main lift shelf or forks in all four (4x or all other provisioned mounting) locations with provided hardware only, prior to use. Load objects are designed to slide on/off smooth platforms without appreciable force, so take care not to push or lean. Keep riser tilt [adjustable angling platform] option flat at all times except for final minor angle adjustment when needed.
  • Do not stand under overhanging load.
  • Do not use on uneven surface, incline or decline (major ramps).
  • Do not stack loads.
  • Do not operate while under the influence of drugs or alcohol.
  • Do not support ladder against LIFT TOOL (unless the specific allowance is provided for one following qualified procedures for working at elevations with this TOOL).
  • Tipping hazard. Do not push or lean against load with raised platform.
  • Do not use as a personnel lifting platform or step. No riders.
  • Do not stand on any part of lift. Not a step.
  • Do not climb on mast.
  • Do not operate a damaged or malfunctioning LIFT TOOL machine.
  • Crush and pinch point hazard below platform. Only lower load in areas clear of personnel and obstructions. Keep hands and feet clear during operation.
  • No Forks. Never lift or move bare LIFT TOOL MACHINE with pallet truck, jack or fork lift.
  • Mast extends higher than platform. Be aware of ceiling height, cable trays, sprinklers, lights, and other overhead objects.
  • Do not leave LIFT TOOL machine unattended with an elevated load.
  • Watch and keep hands, fingers, and clothing clear when equipment is in motion.
  • Turn Winch with hand power only. If winch handle cannot be cranked easily with one hand, it is probably over-loaded. Do not continue to turn winch past top or bottom of platform travel. Excessive unwinding will detach handle and damage cable. Always hold handle when lowering, unwinding. Always assure self that winch is holding load before releasing winch handle.
  • A winch accident could cause serious injury. Not for moving humans. Make certain clicking sound is heard as the equipment is being raised. Be sure winch is locked in position before releasing handle. Read instruction page before operating this winch. Never allow winch to unwind freely. Freewheeling will cause uneven cable wrapping around winch drum, damage cable, and may cause serious injury.
  • This TOOL must be maintained correctly for IBM Service personnel to use it. IBM shall inspect condition and verify maintenance history before operation. Personnel reserve the right not to use TOOL if inadequate. (C048)
CAUTION:
Service platform adapter TOOL also called a UNIT INSTALL WEDGE. Platform/wedge TOOL is for service usage by authorized IBM personnel only, following trained procedures. Always keep it to lowest level possible for moving, transporting, positioning, and/or adjusting items placed upon it, in conjunction with qualified LIFT TOOLS. (L032)
DANGER
Serious injury or death can occur if loaded lift tool falls over or if a heavy load falls off the lift tool. Always completely lower the lift tool load plate and properly secure the load on the lift tool before moving or using the lift tool to lift or move an object. (D010)

Singapore certification requirement

The Vestil lift tool is classified as a lifting machine under Singapore law. Customers who order this equipment for use in Singapore must comply with the following regulatory requirements before the lift tool is put into service.

Ownership of the equipment transfers to the customer upon shipment. As the equipment owner, the customer is responsible for:

  • Engaging an Authorized Examiner (AE) to inspect and certify the lift tool before first use.
  • Obtaining a valid certificate issued by the AE prior to the planned installation date.
  • Scheduling and maintaining all required periodic re-examinations to keep the certificate current.
Important: Certification by an Authorized Examiner is a mandatory prerequisite for lifting machines in Singapore. A Competent Person (CP) does not satisfy this initial certification requirement. The IBM Systems Service Representative (SSR) cannot operate the lift tool on-site until a valid AE certificate is in place. Customers must ensure certification is obtained and available before the scheduled installation date to avoid delays.