Worksheet start pages

Edit online
Table 1. Worksheet Start Table

___ 001.

Is this a new HMC and CPC install or are we installing an HMC and or SE/CPC into an existing network?

If new, go to step 002.

If existing, go to step 005.
___ 002.

Attach HMC eth0/em1 and SE Interface 1 to the same LAN network. Continue with step 003 to configure the Customer or Open Environment HMC connections.

If new, go to step 006.

If existing, go to step 004.
___ 003.

This completes the information needed for the install. Use this information to complete the necessary table information located in the HMC and SE worksheet tables section of this document.
___ 004.

Is this a new HMC install only?

If yes, continue with this step.

If no, go to step 005.

This step assumes you are installing a new HMC into an existing HMC/Support Element network. Log on to an HMC that will be in the same network as this HMC with the user ID of ACSADMIN.

Log on to an exiting HMC and navigate to the Customize Network Settings task under HMC Management.

Using these panels as a reference, fill in the fields below for the settings of the new HMC.

Note: HMC Name and IP addresses entries must be different from any other HMC in that network.

HMC Console Name: ____________________

Domain Name: ____________________

eth0/em1

TCP/IP Interface 1 Address: ___________________________

TCP/IP Interface 1 Network Mask: __________________________

eth1/em2

HMC to obtain IP address automatically on eth1/em2 as a DHCP Client?

If yes, select Obtain IP Address Automatically in eth1/em2 LAN details.

If no, select Specify an IP address and fill in the information below:

TCP/IP Interface 2 Address: ________________________

TCP/IP Interface 2 Network Mask: ___________________________

Name Services: ________________ , __________________

Routing Gateway Address: __________________ (select eth1/em2 in interface field)

Other Routing Information: ______________ , _____________ (optional)

Continue with the step 003.
___ 005.

This step assumes you are installing a new CPC into an existing HMC/SE Network. Log on to an SE that will be in the same network as this SE with the user ID of ACSADMIN.

Log on to an exiting HMC and navigate to the Customize Network Settings task under HMC Management.

Using these panels as a reference, fill in the fields below for the settings of the new SE.

Note: SE Name and IP addresses entries must be different from any other SE in that network.

Support Element Name: ________________________

Address 1 Information (em3):

Primary: _______________________________

Alternate: ______________________________

Network Mask: __________________________________

Address 2 Information (em4):

Primary: ____________________________

Alternate: ___________________________

Network Mask: ____________________________________

Routing Information (if applicable): ______________________

___ 006.

This step assumes you are installing a new HMC and not using the default IP address on the Service LAN.

Note: The customer must supply the following network information to correctly install the CPC.

HMC Setup Information

HMC Console Name: ________________________

Domain Name: ________________________

TCP/IP Interface 1 Address (eth0/em1): __________________________

TCP/IP Interface 1 Network Mask: ____________________________

HMC to obtain IP address automatically on eth1/em2 as a DHCP Client?

If yes, select Obtain IP Address Automatically in eth1/em2 LAN details.

If no, select Specify an IP address and fill in the information below:

TCP/IP Interface 2 Address (eth1/em2): __________________________

TCP/IP Interface 2 Network Mask: ____________________________

Name Services (if applicable): ______________ , _________________

Routing Gateway Address: ______________ (select eth1/em2 in Gateway Device field)

Other Routing Information (optional): _____________ , ______________

Support Element Network Setup Information

Support Element Name: ___________________________

Address 1 Information (em3):

Primary: ____________________________________

Alternate: ___________________________________

Network Mask: ______________________________________

Address 2 Information (em4) (not used on 2097 z10):

Primary: ____________________________________

Alternate: ___________________________________

Network Mask: ______________________________________

Routing Information (if applicable): ____________________

Continue with step 004.
___ 007.

This step assumes you are installing a new HMC managed by the same administrator as a per-existing machine at the same site. If this is not the case, go to the next step. Log on to an existing HMC with the same user ID of the ACSADMIN.

Log on to an exiting SE or an HMC managing the SE and navigate to the Customize Customer Information task under HMC Management.

Using the Administration and System windows as a reference, fill in the fields on the Call Home contact Worksheet to be copied onto the new SE/HMC.

Note: The client must confirm that any carry-forward contact call home data is correct.
___ 008.

This step assumes you are installing a new HMC or SE for which the client has specified a new call home contact or when there is no existing SE/HMC with the same administrator at the site. The client must provide the information outline on the Call Home Contact Information Worksheet.

Note: The customer must supply the following Call Home Contact information to correctly install the CPC.