Worksheet start pages

___ 001.

Is this a new HMC and CPC install or are we installing an HMC and or SE/CPC into an existing network?

If new, go to step 002.

If existing, go to step 005.

___ 002.

Attach HMC eth0/em1 and SE Interface 1 to the same LAN network. Continue with step 003 to configure the Customer or Open Environment HMC connections.

If new, go to step 006.

If existing, go to step 004.

___ 003.

This completes the information needed for the install. Use this information to complete the necessary table information located in the HMC and SE worksheet tables section of this document.

___ 004.

Is this a new HMC install only?

If yes, continue with this step.

If no, go to step 005.

This step assumes you are installing a new HMC into an existing HMC/Support Element network. Log on to an HMC that will be in the same network as this HMC with the user ID of ACSADMIN.

Log on to an exiting HMC and navigate to the Customize Network Settings task under HMC Management.

Using these panels as a reference, fill in the fields below for the settings of the new HMC.

Note: HMC Name and IP addresses entries must be different from any other HMC in that network.

HMC Console Name: ____________________

Domain Name: ____________________

eth0/em1

TCP/IP Interface 1 Address: ___________________________

TCP/IP Interface 1 Network Mask: __________________________

eth1/em2

HMC to obtain IP address automatically on eth1/em2 as a DHCP Client?

If yes, select Obtain IP Address Automatically in eth1/em2 LAN details.

If no, select Specify an IP address and fill in the information below:

TCP/IP Interface 2 Address: ________________________

TCP/IP Interface 2 Network Mask: ___________________________

Name Services: ________________ , __________________

Routing Gateway Address: __________________ (select eth1/em2 in interface field)

Other Routing Information: ______________ , _____________ (optional)

Continue with the step 003.

___ 005.

This step assumes you are installing a new CPC into an existing HMC/SE Network. Log on to an SE that will be in the same network as this SE with the user ID of ACSADMIN.

Log on to an exiting HMC and navigate to the Customize Network Settings task under HMC Management.

Using these panels as a reference, fill in the fields below for the settings of the new SE.

Note: SE Name and IP addresses entries must be different from any other SE in that network.

Support Element Name: ________________________

Address 1 Information (em3):

Primary: _______________________________

Alternate: ______________________________

Network Mask: __________________________________

Address 2 Information (em4):

Primary: ____________________________

Alternate: ___________________________

Network Mask: ____________________________________

Routing Information (if applicable): ______________________

___ 006.

This step assumes you are installing a new HMC and not using the default IP address on the Service LAN.

Note: The customer must supply the following network information to correctly install the CPC.

HMC Setup Information

HMC Console Name: ________________________

Domain Name: ________________________

TCP/IP Interface 1 Address (eth0/em1): __________________________

TCP/IP Interface 1 Network Mask: ____________________________

HMC to obtain IP address automatically on eth1/em2 as a DHCP Client?

If yes, select Obtain IP Address Automatically in eth1/em2 LAN details.

If no, select Specify an IP address and fill in the information below:

TCP/IP Interface 2 Address (eth1/em2): __________________________

TCP/IP Interface 2 Network Mask: ____________________________

Name Services (if applicable): ______________ , _________________

Routing Gateway Address: ______________ (select eth1/em2 in Gateway Device field)

Other Routing Information (optional): _____________ , ______________

Support Element Network Setup Information

Support Element Name: ___________________________

Address 1 Information (em3):

Primary: ____________________________________

Alternate: ___________________________________

Network Mask: ______________________________________

Address 2 Information (em4) (not used on 2097 z10):

Primary: ____________________________________

Alternate: ___________________________________

Network Mask: ______________________________________

Routing Information (if applicable): ____________________

Continue with step 004.