Event messagesEdit online These messages are provided by the event component. GLGSY0000W The service was terminated and restarted unexpectedly. GLGSY0001E The configuration component has failed to apply a configuration change. A reboot is required. GLGSY0002E The configuration component has failed to apply the appliance configuration during appliance startup. A reboot is required. GLGSY0003E The configuration component has failed to successfully validate policy during appliance startup. A reboot is required. GLGSY0004E An unexpected failure has occurred in the configuration component. GLGSY0005E The attempted policy migration has failed. GLGSY0006E An attempt to locate and copy specified files to new partition during policy migration has failed. GLGSY0007E The directory, directory_name, is not valid. The creation of a support information file has failed. GLGSY0008W Information needed for a support information file has not been found. GLGSY0009W An attempt to add a comment to a support information file has failed GLGSY0010E An attempt to apply a configuration change using a settings snapshot has failed. The previous policy has been restored. GLGSY0011E Restoring the previous policy after a failed attempt to apply a configuration from a settings snapshot file has resulted in at least one failure. GLGSY0012E The policy was not validated by the configuration component. The configuration was rolled back and the Local Management Interface was restarted. GLGSY0013E The configuration was not reset to the factory defaults. GLGSY0014I The configuration was reset to the factory defaults. GLGSY0015I The startup configuration is complete. GLGSY0016E The appliance was automatically restarted to recover from a startup configuration attempt that failed. GLGSY0017E Restart the appliance manually to recover from a startup configuration attempt that failed. GLGSY0018E An unrecoverable error has occurred while attempting to configure network interfaces. GLGSY0019W The component_name has stopped unexpectedly. GLGSY0020I User user_name logged on to the appliance. GLGSY0021W Authentication failed for user user_name. GLGSY0022E FIPS error detected. Checksum validation failed for file file_name. GLGSY0023E FIPS error detected. File file_name has been deleted. GLGSY0024E FIPS error detected. Component component_name has failed to enter FIPS mode. GLGSY0025I Component component_name has successfully entered FIPS mode. GLGSY0026I Component sshd has successfully entered FIPS mode. GLGSY0027W Invalid SNMP alert configuration: algorithm_name is not allowed in FIPS mode. GLGSY0028E FIPS error detected. Component sshd has failed to enter FIPS mode. GLGSY0029I Appliance has entered FIPS mode. GLGSY0030I The default CA certificate was automatically renewed. The new expiration date is expire_date. GLGSY0031W The Certificate Authority with subject name, subject_name, expires in less than num_days days. GLGSY0032E The attempt to update the route, route_detail, has failed. GLGSY0033W The certificate with subject name, subject_name, expires in less than num_days days. GLGSY0034I The LMI has been configured to use the default self-signed certificate. GLGSY0034W A problem was detected in the security content installed on this appliance and certain signatures may not operate properly. GLGSY0035I The LMI has been configured to use a custom user provided certificate. GLGSY0036W The certificate with subject name, subject_name, has expired. GLGSY0037W The Certificate Authority with subject name, subject_name, has expired. GLGSY0038W The hardware watchdog timer did not initialize properly. GLGSY0039W The system memory use of value percent has exceeded the specified limit of limit percent. GLGSY0040W The disk consumption of value percent of the root partition has exceeded the specified limit of limit percent. GLGSY0041E Network interface module in bank bank is below the minimum supported firmware version for this appliance. This network interface module will be disabled. Current firmware version is currentVersion. Minimum required firmware version is minimumVersion. GLGSY0042I Call Home service has started. GLGSY0043I Call Home service has successfully submitted: problem_desc PMR pmr_id. GLGSY0044I IPS events log database has been cleared. GLGSY0044W Call Home service was unable to submit a service request for: problem_desc (on problem_timestamp) GLGSY0045I Network access events log database has been cleared. GLGSY0046W Network interface module in bank bank, with serial number serial, is not compatible with this appliance. This network interface module will be disabled. GLGSY0047I All hardware bypass controllers have switched to connected mode. GLGSY0048I All hardware bypass controllers have switched to fail mode. GLGSY0049E System reboot due to a fatal error in root file system. GLGSY0050I Malware analysis status database has been cleared. GLGSY0100W An attempt was made to log on using an unknown user, 'user_name', from 'remote_host'. GLGSY0101W An incorrect password was provided for the user, 'user_name', from 'remote_host'. GLGSY0102I The user, 'user_name' from 'remote_host', was logged out of the system. GLGSY0103I The user, 'user_name' from 'remote_host', was successfully authenticated. GLGSY0104W The account for user, 'user_name' from 'remote_host', has been locked. GLGSY0105W The login was rejected for the unprivileged user, 'user_name' from 'remote_host'. GLGSY0106W The account has not been enabled for the user 'user_name' from 'remote_host'. GLGSY0107W The account has expired for the user 'user_name' from 'remote_host'. GLGSY0108I The user 'user_name' from 'remote_host' reset their own password. GLGSY9025I Component component_name has successfully entered FIPS mode. GLGSY9026I Component sshd has successfully entered FIPS mode. GLGSY9029I Appliance has entered FIPS mode. GLGSY9030I The default CA certificate was automatically renewed. The new expiration date is expire_date. GLGSY9034I The LMI has been configured to use the default self-signed certificate. GLGSY9035I The LMI has been configured to use a custom user provided certificate. GLGSY9042I The appliance has been configured to use the default self-signed certificate for central_management_entity bi-directional authentication. GLGSY9043I The appliance has been configured to use a custom user provided certificate for central_management_entity bi-directional authentication. Parent topic: Appliance messages