Device drivers completion codes: Media changers
IBM Storage Protect device drivers provide completion codes that are specific to media changer devices.
The following table shows completion code values for IBM Storage Protect device drivers for media changers. Each entry provides a description for the I/O error message and the recommended action. After performing the recommended action, try the failing operation again.
| Decimal | Hexadecimal | Description | Recommended action |
|---|---|---|---|
| 300 | X'12C' | Cartridge entry/exit error | Check the entry/exit ports for a jammed volume. |
| 301 | X'12D' | Cartridge load failure | Check the drive for jammed volumes. On AIX®, display the errpt to check for hardware errors. |
| 302 | X'12E' | Cartridge in failed drive | Check the drive for jammed volumes. On AIX, display the errpt to check for hardware errors. |
| 303 | X'12F' | Carousel not loaded | Ensure that the carousel is correctly in place and the door is shut. |
| 304 | X'130' | Changer failure | On AIX, display the errpt to check for hardware errors. |
| 305 | X'131' | Drive failure | Ensure that the heads are clean. On AIX, display the errpt to check for hardware errors. |
| 306 | X'132' | Drive or media failure | Ensure that the heads are clean. On AIX, display the errpt to check for hardware errors. |
| 307 | X'133' | Entry/exit failure | Check the tape library interface for hardware errors. If there are no errors, contact IBM Storage Protect Support. |
| 308 | X'134' | Entry/exit port not present | Check the tape library interface for hardware errors. If there are no errors, contact IBM Storage Protect Support. |
| 309 | X'135' | Library audit error | Ensure that there are no jammed volumes. It is possible that the library audit is failing due to hardware errors. On AIX, display the errpt to check for hardware errors. |
| 310 | X'136' | Library full | Check for jammed volumes. Ensure that the volumes are not rearranged. If the library is not full, start the AUDIT LIBRARY command. |
| 311 | X'137' | Media export | Check the tape library interface for hardware errors. If there are no errors, contact IBM Storage Protect Support. |
| 312 | X'138' | Slot failure | Ensure that nothing is jammed in the slot. |
| 313 | X'139' | Slot or media failure | Ensure that the volume is not jammed in the slot and that the volumes are not rearranged. If the problem persists, start the AUDIT LIBRARY command. |
| 314 | X'13A' | The source slot or drive was empty in an attempt to move a volume | Ensure that the volumes are not rearranged. If the problem persists, start the AUDIT LIBRARY command. |
| 315 | X'13B' | The destination slot or drive was full in an attempt to move a volume | Ensure that the volumes are not rearranged, or that a volume is not stuck in the drive. If problem persists, start the AUDIT LIBRARY command. |
| 316 | X'13C' | Cleaner cartridge installed | Contact IBM Storage Protect support. |
| 317 | X'13D' | Media not ejected | Ensure that the volumes are not rearranged, or that a volume is not stuck in the drive. If problem persists, start the AUDIT LIBRARY command. |
| 318 | X'13E' | I/O port not configured | Contact IBM Storage Protect Support. |
| 319 | X'13F' | First destination empty | Ensure that the volumes are not rearranged. If problem persists, start the AUDIT LIBRARY command. |
| 320 | X'140' | No inventory information | Start the AUDIT LIBRARY command. |
| 321 | X'141' | Read element status mismatch | Ensure that host bus adapter drivers and firmware are at current levels. Check the tape library interface for hardware errors. If there are no errors, contact IBM Storage Protect Support. |
| 322 | X'142' | Initialize range failed | Check the tape library interface for hardware errors. If there are no errors, contact IBM Storage Protect Support. |