SevOne Data Insight Appliance Insert

SevOne Documentation

All documentation is available from the IBM SevOne Support customer portal.

© Copyright International Business Machines Corporation 2023.

All right, title, and interest in and to the software and documentation are and shall remain the exclusive property of IBM and its respective licensors. No part of this document may be reproduced by any means nor modified, decompiled, disassembled, published or distributed, in whole or in part, or translated to any electronic medium or other means without the written consent of IBM.

IN NO EVENT SHALL IBM, ITS SUPPLIERS, NOR ITS LICENSORS BE LIABLE FOR ANY DAMAGES, WHETHER ARISING IN TORT, CONTRACT OR ANY OTHER LEGAL THEORY EVEN IF IBM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND IBM DISCLAIMS ALL WARRANTIES, CONDITIONS OR OTHER TERMS, EXPRESS OR IMPLIED, STATUTORY OR OTHERWISE, ON SOFTWARE AND DOCUMENTATION FURNISHED HEREUNDER INCLUDING WITHOUT LIMITATION THE WARRANTIES OF DESIGN, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT.

IBM, the IBM logo, and SevOne are trademarks or registered trademarks of International Business Machines Corporation, in the United States and/or other countries. Other product and service names might be trademarks of IBM or other companies. A current list of IBM trademarks is available on ibm.com/trademark.

Instructions

The instructions in this document do not apply if you are deploying SevOne Data Insight .ova to your own Linux machines. To deploy SevOne Data Insight using .ova, please refer to SevOne Data Insight Pre-Installation Guide for details.

For appliance-based installation, please execute the steps below.

  1. Unpack SevOne Data Insight appliance and identify each item.

    1. Rail Kit
    2. Cable Management Arm (CMA) Kit
    3. Faceplate/Bezel
    4. Power Cords
    5. SevOne Data Insight Appliance

  2. Install the appliance into a computer cabinet/rack. See the Rack Installation Instructions booklet located in the Rail Kit box.

    You will install the faceplate/bezel in a later step.

  3. Connect a keyboard and a monitor to the SevOne Data Insight appliance. Typically you use the connections on the front of the appliance, although you can use the connections on the back of the appliance.

    If you connect two monitors, only the monitor you connect to the front of the appliance displays.

  4. Connect the network RJ45 cable to the eth0 port on the back of the appliance.

  5. Plug in all applicable power cords: two cords for appliance (second for redundancy), one for monitor.

    A green light flashes on the back and the network port light flashes but you have yet to power on the appliance.

  6. Press the Power button on the top right corner on the front of the appliance to power on your SevOne Data Insight appliance and power on the monitor.

  7. Appliance front view.

    PASFrontView

    Item
    Ports, Panels, & Slots
    		 Icon Description
    		Left Control Panel N/A Contains the system health and system ID, status LED, and the iDRAC Quick Sync 2 (wireless) indicator.
    The iDRAC Quick Sync 2 indicator is available only on certain configurations.
    Status LED: Enables you to identify any failed hardware components. There are up to five status LEDs and an overall system health LED (Chassis health and system ID) bar.
    Quick Sync 2 (wireless): Indicates a Quick Sync enabled system. The Quick Sync feature is optional. This feature allows management of the system by using mobile devices. This feature aggregates hardware or firmware inventory and various system level diagnostic and error information that can be used in troubleshooting the system. For more information, see the Integrated Dell Remote Access Controller User’s Guide at http://dell.com/poweredgemanuals.
    		Drive Slots N/A Enable you to install drives that are supported on your system.
    		VGA Port images/vgaPort.jpg Enables you to connect a display device to the system.
    		Right Control Panel N/A Contains the power button, USB port, iDRAC Direct micro port, and the iDRAC Direct status LED.
    		Information Tag N/A The Information Tag is a slide-out label panel that contains system information such as Service Tag, NIC, MAC address, and so on.

  8. Appliance rear view.

    PASRearView

    Item
    Ports, Panels, & Slots
    		 Icon Description
    		PCIe expansion card slot(3) N/A The expansion slot(s) enable you to connect PCI Express expansion cards. If you have purchased an add-on NIC, it will be installed here.
    		Power supply unit (2) N/A Power supply.
    		NIC port (4) images/nicPort.png The NIC ports that are integrated on the network daughter card (NDC) provide network connectivity. eth0 will be the left-most port.
    		USB 3.0 port (2) images/usb3.0Port.png The USB ports are 9-pin and 3.0-compliant. These ports enable you to connect USB devices to the system.
    		VGA port images/vgaPort.jpg Enables you to connect a display device to the system.
    		Serial port images/serialPort.png Enables you to connect a serial device to the system.
    		iDRAC9 dedicated network port images/iDRAC9Port.png Use the iDRAC9 dedicated network port to securely access the embedded iDRAC on a separate management network, see the http://dell.com/poweredgemanuals.
    		System status indicator cable port N/A Enables you to connect the status indicator cable and view system status when the CMA is installed.
    		System identification button images/systemIdentificationButton.png The System Identification (ID) button is available on the front and back of the systems. Press the button to identify a system in a rack by turning on the system ID button. You can also use the system ID button to reset iDRAC and to access BIOS using the step through mode.

  9. Wait as the following messages appear when the appliance powers on (~ 3 minutes).

    1. Configure Memory
    2. BIOS Revision
    3. Select "Install SevOne DataInsight v6.6.0"

  10. When the console prompt appears, enter localhost login/password as sevone/sevone.

    sevone is the default password.

    You are required to change the default password as failure to do so presents a significant security risk.

  11. After successful deployment of each appliance, configure the network settings. Please refer to section Configure Network Settings in SevOne Data Insight Pre-Installation Guide for details.

SevOne Documentation

All SevOne Data Insight user documentation is available online from https://www.ibm.com/docs/en/sevone-npm

For help, contact IBM SevOne Support via phone (https://www.ibm.com/planetwide/)or go to IBM SevOne Support customer portal (https://www.ibm.com/mysupport/).