Problems with loading and starting the operating system (Linux)

If the system is running partitions from partition standby (LPAR), the following procedure addresses the problem in which one partition will not boot Linux while other partitions boot successfully and run the operating system successfully.

1. Is a management console attached to the managed system?
   • Yes: Continue with the next step.
   • No: Go to step 3.
2. Look at the service action event error log on the management console. Perform the actions necessary to resolve any open entries that affect devices in the boot path of the partition or that indicate problems with I/O cabling. Then try to reboot the partition. Does the partition reboot successfully?
   • Yes: This ends the procedure.
   • No: Continue with the next step.
3. Boot to the SMS main menu:
   • If you are rebooting a partition from partition standby (LPAR), go to the properties of the partition and select Boot to SMS, then activate the partition.
   • If you are rebooting from platform standby, access the ASMI. See Accessing the Advanced system Management Interface using a Web browser. Select Power/Restart Control, then Power On/Off System. In the Linux partition mode boot box, select Boot to SMS menu > Save Settings and Power On.

   At the SMS main menu, select Select Boot Options and verify whether the intended boot device is correctly specified in the boot list. Is the intended load device correctly specified in the boot list?

   • Yes: Perform the following steps:
     1. Remove all removable media from devices in the boot list from which you do not want to load the operating system.
     2. If you are attempting to load the operating system from a network, go to step 4.
     3. If you are attempting to load the operating system from a disk drive or an optical drive, go to step 7.
     4. No: Go to step 5.
4. If you are attempting to load the operating system from the network, perform the following steps:
   • Verify that the IP parameters are correct.
   • Use the SMS ping utility to attempt to ping the target server. If the ping is not successful, have the network administrator verify the server configuration for this client.
   • Check with the network administrator to ensure that the network is up. Also ask the network administrator to verify the settings on the server from which you are trying to load the operating system.
   • Check the network cabling to the adapter.

   Restart the partition and try loading the operating system. Does the operating system load successfully?

   • Yes: This ends the procedure.
   • No: Go to step 7.
5. Use the SMS menus to add the intended boot device to the boot sequence. Can you add the device to the boot sequence?
   • Yes: Restart the partition. This ends the procedure.
   • No: Continue with the next step.
6. Ask the customer or system administrator to verify that the device you are trying to load from is assigned to the correct partition. Then select List All Devices and record the list of bootable devices that displays. Is the device from which you want to load the operating system in the list?
   • Yes: Go to step 7.
   • No: Go to step 10.
7. Try to load and run standalone diagnostics against the devices in the partition, particularly against the boot device from which you want to load the operating system. You can run standalone diagnostics from an optical drive or a NIM server. To boot standalone diagnostics, follow the detailed procedures in Running the online and standalone diagnostics.
   Note: When attempting to load diagnostics on a partition from partition standby, the device from which you are loading standalone diagnostics must be made available to the partition that is not able to load the operating system, if it is not already in that partition. Contact the customer or system administrator if a device must be moved between partitions in order to load standalone diagnostics.

   Did standalone diagnostics load and start successfully?

   • Yes: Go to step 8.
   • No: Go to step 14.
8. Was the intended boot device present in the output of the option Display Configuration and Resource List, that is run from the Task Selection menu?
   • Yes: Continue with the next step.
   • No: Go to step 10.
9. Did running diagnostics against the intended boot device result in a No Trouble Found message?
   • Yes: Go to step 12.
   • No: Go to the list of service request numbers and perform the repair actions for the SRN reported by the diagnostics. When you have completed the repair actions, go to step 13.
10. Perform the following actions:
    1. Perform the first item in the action list below. In the list of actions below, choose SCSI or IDE based on the type of device from which you are trying to boot the operating system.
    2. Restart the system or partition.
    3. Stop at the SMS menus and select Select Boot Options.
    4. Is the device that was not appearing previously in the boot list now present?
       • Yes: Go to Verify a repair . This ends the procedure.
       • No: Perform the next item in the action list and then return to step 10.b. If there are no more items in the action list, go to step 11.
    Action list:
    Note: See System FRU locations for part numbers and links to exchange procedures.
    1. Verify that the SCSI or IDE cables are properly connected. Also verify that the device configuration and address jumpers are set correctly.
    2. Do one of the following:
       • SCSI boot device: If you are attempting to boot from a SCSI device, remove all hot-swap disk drives (except the intended boot device, if the boot device is a hot-swap drive).If the boot device is present in the boot list after you boot the system to the SMS menus, add the hot-swap disk drives back in one at a time, until you isolate the failing device.
       • IDE boot device: If you are attempting to boot from an IDE device, disconnect all other internal SCSI or IDE devices. If the boot device is present in the boot list after you boot the system to the SMS menus, reconnect the internal SCSI or IDE devices one at a time, until you isolate the failing device or cable.
    3. Replace the SCSI or IDE cables.
    4. Replace the SCSI backplane (or IDE backplane, if present) to which the boot device is connected.
    5. Replace the intended boot device.
    6. Replace the system backplane.
11. Choose from the following:
    • If the intended boot device is not listed, go to PFW1548: Memory and processor subsystem problem isolation procedure. This ends the procedure.
    • If an SRN is reported by the diagnostics, go to the list of service request numbers and follow the action listed. This ends the procedure.
12. Have you disconnected any other devices?
    • Yes: Reinstall each device that you disconnected, one at a time. After you reinstall each device, reboot the system. Continue this procedure until you isolate the failing device. Replace the failing device, then go to step 13.
    • No: Perform an operating system-specific recovery process or reinstall the operating system. This ends the procedure.
13. Is the problem corrected?
    • Yes: Go to Verify a repair . This ends the procedure.
    • No: If replacing the indicated FRUs did not correct the problem, or if the previous steps did not address your situation, go to PFW1548: Memory and processor subsystem problem isolation procedure. This ends the procedure.
14. Is a SCSI boot failure (where you cannot boot from a SCSI-attached device) also occurring?
    • Yes: Go to PFW1548: Memory and processor subsystem problem isolation procedure. This ends the procedure.
    • No: Continue to the next step.
15. Perform the following actions to determine if another adapter is causing the problem:
    1. Remove all adapters except the one to which the optical drive is attached and the one used for the console.
    2. Reload the standalone diagnostics. Can you successfully reload the standalone diagnostics?
       • Yes: Perform the following steps:
         1. Reinstall the adapters that you removed (and attach devices as applicable) one at a time. After you reinstall each adapter, retry the boot operation until the problem reoccurs.
         2. Replace the adapter or device that caused the problem.
         3. Go to Verify a repair . This ends the procedure.
       • No: Continue with the next step.
16. The graphics adapter (if installed), optical drive, IDE or SCSI cable, or system board is most likely defective. Does your system have a PCI graphics adapter installed?
    • Yes: Continue with the next step.
    • No: Go to step 18
17. Perform the following steps to determine if the graphics adapter is causing the problem:
    1. Remove the graphics adapter.
    2. Attach a TTY terminal to the system port.
    3. Try to reload standalone diagnostics. Do the standalone diagnostics load successfully?
       • Yes: Replace the graphics adapter. This ends the procedure.
       • No: Continue with the next step.
18. Replace the following (if not already replaced), one at a time, until the problem is resolved:
    1. Optical drive
    2. IDE or SCSI cable that goes to the optical drive
    3. System board that contains the integrated SCSI or IDE adapters.

    If this resolves the problem, go to Verify a repair . If the problem still persists or if the previous descriptions did not address your particular situation, go to PFW1548: Memory and processor subsystem problem isolation procedure.

    This ends the procedure.