HSCL14xx error codes

These error codes can be displayed in a window that is displayed on the HMC screen during system configuration and operations.
Back to HSCL error codes page
HSCL14xx error codes Message Recovery action
HSCL1400 The firmware operation failed. Try the task again. If the problem persists, contact your next level of support or your service provider.
HSCL1401 An error was detected using the current HMC's network configuration. A duplicate IP address and system hostname may be the cause of this problem. Verify this system's network settings via the 'Customize Network Settings' task. This HMC's network interface has been temporarily disabled and the hostname set to 'localhost.localdomain'.
  1. Ensure that the network setting is correct.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL1402 This operation failed due to following reasons: {0}.  
HSCL1403 Could not display the {0} dialog. Try the operation again.
  1. Refresh the graphical user interface. For details, see Updating managed system or frame information.
  2. Retry the operation.
  3. If it still fails, log off and then log back in to the HMC and try the operation again.
  4. If the problem persists, contact your next level of support or your service provider.
HSCL1450 There is an insufficient number of unallocated processors to perform the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1451 Attempted to allocate a number of processors below the minimum processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1452 Attempted to allocate a number of processors above the maximum processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1453 There is an insufficient amount of unallocated processing units to perform the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1454 Attempted to allocate an amount of processing units below the minimum processing unit setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1455 Attempted to allocate an amount of processing units above the maximum processing setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1456 The processor setting exceeds the maximum system configuration.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1457 There is an insufficient amount of unallocated memory to perform the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1458 Attempted to allocate an amount of memory below the minimum memory setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1459 Attempted to allocate an amount of memory above the maximum memory setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145A The minimum memory amount is below the required amount of memory with the maximum specified.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145B There is an insufficient amount of unallocated 5250 CPW to perform the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145C Attempted to allocate an amount of 5250 CPW below the minimum setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145D Attempted to allocate an amount of 5250 CPW above the maximum setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145E Attempted to allocate processing units greater than the maximum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL145F Attempted to allocate processing units less than the minimum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1460 Attempted to set maximum processing units greater than the maximum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1461 Attempted to set maximum processing units less than the minimum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1462 Attempted to set minimum processing units greater than the maximum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1463 Attempted to set minimum processing units less than the minimum capacity allowed with the specified virtual processor setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1464 The partition is not currently configured for shared processing.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1465 The partition is not currently configured for dedicated processing.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1466 The partition specified is not valid. Rebuild the managed system and try again.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1467 The type of partition specified is not compatible with the operation.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1468 The I/O pool ID specified is not valid.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1469 The shared processor pool ID specified is not valid.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL146A The I/O adapter: {0} is not valid.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL146B The partition name specified has already been used by another partition. Specify a different name.  
HSCL146C The partition name specified is not acceptable. Check the name and try again.  
HSCL146D The partition is currently in a state where this configuration change is not allowed. Rebuild the managed system and try again.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL146E The number of power controlling partitions for this partition is not valid. Check the setting and try again.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL146F Changing from shared to dedicated processing is not allowed with the current processing setting.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1472 The SNI adapter: {0} specified is not valid. Check the entry and try again.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1473 Cannot perform atomic operation. Atomic operations are not enabled.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL1474 The processing weight specified is not valid. Check the entry and try again.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1475 Unable to switch out or into manufacturing default configuration at this point.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL1477 Unable to perform atomic operation(s) at this point since one is already in progress.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL1478 The virtual I/O adapter type specified is not valid. Check the entry and try again.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL1479 The atomic operation failed.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL147A The RIO bus number: {0} is not valid. Check the entry and try again.
  1. Ensure that the setting is valid.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL147B The hardware page table ratio specified is not valid. Check the entry and try again.
  1. For details, see Updating managed system or frame information.
  2. Retry the task
  3. If the problem persists, contact your next level of support or your service provider.
HSCL147C The I/O adapter: {0} cannot be assigned to the pool specified.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL147D Cannot change the processing setting to uncapped.
  1. Rebuild the managed system. For details, see Updating managed system or frame information.
  2. Retry the task.
  3. If the problem persists, contact your next level of support or your service provider.
HSCL147E The OptiConnect pool specified is not acceptable by the managed system. Check the entry and try again.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL147F The HSL OptiConnect pool specified is not acceptable by the managed system. Check the entry and try again.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.
HSCL1481 Cannot perform this operation because the partition belongs to a workload management group joined by other partitions.
  1. Retry the task.
  2. If the problem persists, contact your next level of support or your service provider.