Defining LPAR parameters

LPAR parameters are parameters on the local LPAR that are required to customize Db2® Automation Expert.

1. Specify E next to the LPAR parameters field, and press Enter.
   The LPAR Parameters panel is displayed, as shown in the following figure:

    CCQPLPR            LPAR Parameters                                    10:34:05 
    Command ===>                                                  Scroll ===> CSR  
                                                                                   
    Ensure that values are specified for the required LPAR parameters. Press End   
    to save and exit.                                                              
                                                                                   
    Commands: SAVE  VERIFYOFF                                                      
                                                                       More:     + 
                                                                                   
    Job Entry Subsystem (JES) - common                                             
     *JES version  . . . . . . . . . . . . . . . 2                                 
                                                                                   
    ISPF Libraries - common                                                        
     *Message library  . . . . ISP.SISPMENU                                   Add  
     *ISPF table input library ISP.SISPTENU                                   Add  
                                                                                   
    Language Environment Libraries -common                                         
     *Load library . . . . . . CEE.SCEELLIB                                   Add  
                                                                                   
    Automation Expert LPAR Parameters                                              
     *Automation Expert PROCLIB                                                    
        DAJ.PROCLIB                                                                
      Job tracking started task PROC member  . . DAJPROC                           
     *Job tracking started task Parms data set                                     
        DAJ.PARMLIB(DAJPARM)                                                       
     *Job tracking started task ID . . . . . . . DAJT                              
     *Job tracking started task AUTHID . . . . . DB2USER                           
      Utility Generation address space PROC member                                 
        DAJPRUTG                                                                   
      Utility Execution address space PROC member                                  
        DAJPRUTX                                                                   
                                                                                   

   You can use the following primary commands on this panel:

   SAVE

   Saves the specified product or component parameter values.

   VERIFY / VERIFYOFF

   Use the VERIFY and VERIFYOFF commands to turn on and off parameter verification of LPAR parameters. Before you can generate customization jobs, you must verify that all required parameters are set to a valid value. The LPAR parameter status of Verify Values on the Customize Workplace panel indicates that the values have not been verified.

   Enter these commands either by typing them in the command field and pressing Enter or by positioning the cursor on the command and pressing Enter. When VERIFY is active, VERIFYOFF is displayed so that you can toggle between the two states. By default, verification is turned on when you display the LPAR Parameters panel, and the verification state is reset to VERIFY every time you exit the Customization Workplace panel by pressing PF3.

   Turning verification off is useful when you need to exit the panel before you have entered all of the required parameters, but you want to save the parameters that you have specified. When you disable verification, it is disabled only for the LPAR Parameters Values panel.

2. Specify values for all required parameters that are displayed.
   Many parameters have default values, which you can either accept or change.

   Tips:

   • In the command line, specify the KEYS command, and map EXPAND to one of the function keys.
   • For a detailed description of all input fields, put the cursor in the field, and press F1 or the key that is mapped to Help.
   • The following elements apply to specific fields:
     • Add is displayed when parameters can have multiple values but currently have only one value. To specify multiple values in these fields, place the cursor on Add, and press Enter. Use the displayed panel to add or delete additional values.
     • List is displayed when the complete list of valid values for the fields is too long to be displayed on the panel. To see the complete list of values, place the cursor on List, and press F1 or the key that is mapped to Help.
     • More is displayed when input fields contains multiple values. To see all of the values in the field, place the cursor on More, and press Enter.

   The following LPAR parameters can contain 1 - 64 values:

   • LPAR macro library
   • Message library
   • Panel library
   • Skeleton library
   • ISPF table input library
   • ISPF user profile library
   • File tailoring output library
   • Link list library
   • Command procedures library
   • Macro library
   • Link-edit library
   • Load library
   • Started task library name
3. Press End to save your changes and exit, or issue the SAVE command to save your changes and stay on the same panel.