KLVPM021 INPUT PROCESSING EXCEPTION: RC=rc,lu_name, modname,attention_code,fdbk, error_data,datastream
Explanation
An input message from the physical terminal has
caused an exception condition in PSM where:
- rc: Identifies the reason for the error. See the following reason code analysis table for more information.
- lu_name: Physical terminal LU name.
- modname: Module identifier.
- attention_code: Pending AID.
- fdbk: Feedback information internal to TMS:Engine.
- error_data: Two bytes of error data. See the following reason code analysis table for a description of the valid data.
- datastream: Up to first ten bytes of the input message causing the exception.
The following table lists possible reason codes for the
input exception with associated system action codes and user response
codes. After locating the reason code, refer to the appropriate system
action and user response following this table:
| Reason Code | Description | System Action | User Response |
|---|---|---|---|
| 0601 | Internal Exception Condition | 1 | 1 |
| 0602 | Internal Exception Condition | 1 | 1 |
| 0603 | Internal Exception Condition | 1 | 1 |
| 0604 | Internal Exception Condition | 1 | 1 |
| 0605 | Internal Exception Condition | 1 | 1 |
| 0606 | Internal Exception Condition | 2 | 1 |
| 0607 | Internal Exception Condition | 2 | 1 |
| 0608 | Internal Exception Condition | 2 | 1 |
| 0609 | Internal Exception Condition | 1 | 1 |
| 060A | Internal Exception Condition | 1 | 1 |
| 060B | Internal Exception Condition | 1 | 1 |
| 060C | Internal Exception Condition | 1 | 1 |
| 060D | Internal Exception Condition | 1 | 1 |
| 060E | Internal Exception Condition | 1 | 1 |
| 0901 | Internal Exception Condition | 1 | 1 |
| 0902 | Internal Exception Condition | 1 | 1 |
| 0903 | Internal Exception Condition | 1 | 1 |
| 0904 | Internal Exception Condition | 1 | 1 |
| 0905 | Unsupported AID received (error_data = unsupported aid) | 1 | 2 |
| 0906 | Invalid CLEAR/CLEAR partition | 1 | 2 |
| 0907 | Internal Exception Condition | 1 | 1 |
| 0908 | Internal Exception Condition | 1 | 1 |
| 0909 | Internal Exception Condition | 1 | 1 |
| 090A | Invalid buffer address (error_data = buffer address) | 1 | 2 |
| 090B | Invalid codepoint detected (error_data = codepoint) | 1 | 2 |
| 090C | Invalid value in Set Attribute (error_data = Set Attribute type/value pair) | 1 | 2 |
| 090D | Unexpected end of output (error_data = last 1 or 2 bytes) | 1 | 2 |
| 090E | Internal Exception Condition | 2 | 1 |
| 090F | Internal Exception Condition | 2 | 1 |
| 0910 | Internal Exception Condition | 2 | 1 |
| 0911 | Internal Exception Condition | 2 | 1 |
| 0912 | Internal Exception Condition | 2 | 1 |
| 0913 | Unexpected formatted input (error_data = buffer address) | 2 | 2 |
| 0914 | Input data from unknown field (error_data = buffer address) | 2 | 2 |
| 0915 | Attention key received during pre-popup read. | 2 | 2 |
| 0916 | Read modified already satisfied. | 2 | 2 |
System action
One of the following:
- Action 1. Error recovery displays the TERMINAL INPUT ERROR message on the terminal. The input message is rejected with an appropriate sense code and normal processing resumes.
- Action 2. Error recovery ignores the input message and normal processing resumes.
User response
One of the following:
- If the TERMINAL INPUT ERROR message displays, press ENTER to remove the message and continue normal operation. If the problem persists, the system administrator should obtain a VSSTRACE of the failure and a copy of any related error messages and contact IBM® Software Support.
- If the TERMINAL INPUT ERROR message displays, press ENTER to remove the message and continue normal operation. If the problem persists, the system administrator should analyze the failure and contact the appropriate hardware or software vendor.
Message Type
INFO