For the createNode command, the valid properties for a System Service Monitors agent include: SVCUSERNAME, SVCPASSWORD, SNMPPORT, SNMPCOMMUNITY, COEXIST, OVERWRITE, SERVER_GUI, MS_SNMP_OVERRIDE, DISABLE_SNMPV2, V3AUTHPROTOCOL, V3AUTHPASSWORD, V3PRIVPROTOCOL, CORE_ONLY, V3PRIVPASSWORD, MANUAL_SERVICE, CLUSTER_INST, CLUSTER_GROUP, CORE_CONFIG_DISK, AGENTLOG, BYPASS_RECONFIG, AGENTLOGSIZE, SNMPTRAPVER, CONFIGDIR, INST_CONSOLE. The values are to be specified in key=value format. Values can differ per system.
Property name in key format defined for createNode, updateAgent, configureSystem, and removeSystem commands | Property name in SECTION.KEY format required for createGroup, addGroupMember, and editGroupMember commands | Description |
---|---|---|
SVCUSERNAME | SSMCONFIG.
SVCUSERNAME |
For Windows® systems, this property sets the username used to register the Netcool/SSM service. If you specify this switch, you must also specify the SvcUserPassword parameter. On host computers with Active Directory installed (Windows 2000 domain controllers) this parameter is ignored and the local system account is used instead. The default: local system account. |
SVCPASSWORD | SSMCONFIG.
SVCPASSWORD |
For Windows systems, this property, sets the password used to register the Netcool/SSM service. If you specify this parameter, you must also specify the SvcUser switch. On host computers with Active Directory installed (Windows 2000 domain controllers) this parameter is ignored and the local system account is used instead. |
SNMPPORT | SSMCONFIG.
SNMPPORT |
The UDP port on which Netcool/SM Configuration listens for incoming SNMP requests. This port must be a number in the range 1-65535 inclusive and must not be in use by any other application. |
SNMPCOMMUNITY | SSMCONFIG.
SNMPCOMMUNITY |
The community string for SNMP v1 and v2. |
OVERWRITE | SSMCONFIG.
OVERWRITE |
For Windows systems, this property specifies that the current Netcool/Service Monitor Configuration installation is retained in the new installation: Y - configuration not retained, N - configuration retained. |
SERVER_GUI | SSMCONFIG.
SERVER_GUI |
For Windows systems, this property installs the Netcool/SSM agent GUI components on server computers. These components (the MIB Explorer, Service Controller, and Desktop Help) are usually only installed on desktop computers: Y - Netcool/SSM agent GUI components are installed on server computers, N - no Netcool/SSM agent GUI components are installed on server computers. |
MS_SNMP_OVERRIDE | SSMCONFIG.
MS_SNMP_ OVERRIDE |
For Windows systems, if OverrideSNMP is specified, the installer stops the Microsoft® SNMP service, sets its startup mode to manual, installs the Netcool/Service Monitor Configuration service and registers the Netcool/Service Monitor Configuration service in automatic startup mode. If OverrideSNMP is not specified, the installer leaves the Microsoft SNMP service running and registers the Netcool/ Service Monitor Configuration service in manual startup mode. |
DISABLE_SNMPV1 | SSMCONFIG.
DISABLE_SNMPV1 |
Set to enable Netcool/SM Configuration to respond to SNMP v1 requests. |
DISABLE_SNMPV2 | SSMCONFIG.
DISABLE_SNMPV2 |
Set to enable Netcool/SM Configuration to respond to SNMP v2 requests. |
V3User | SSMCONFIG.V3User | Sets the username used by Netcool/SM Configuration in SNMPv3 communication. |
V3AUTHPROTOCOL | SSMCONFIG.
V3AUTHPROTOCOL |
Sets the method of authentication used for the SNMP v3 protocol. Valid values are: NONE - No authentication, SHA - Secure Hash Algorithm, and MD5 - MD5 message digest algorithm. If you select a value other than NONE, you must also specify a password. |
V3AUTHPASSWORD | SSMCONFIG.
V3AUTHPASSWORD |
Sets the password used in SNMPv3 authentication. This password must be at least 8 characters in length and can contain spaces. |
V3PRIVPROTOCOL | SSMCONFIG.
V3PRIVPROTOCOL |
Sets the method used for encrypting SNMP v3 protocol messages. Valid values are: NONE - no encryption used and DES - Data Encryption Standard algorithm. If you set this parameter to a value other than NONE, you must also specify a password. |
V3PRIVPASSWORD | SSMCONFIG.
V3PRIVPASSWORD |
Sets the password used in SNMPv3 encryption. This password must be at least 8 characters in length and can contain spaces. |
CORE_ONLY | SSMCONFIG.
CORE_ONLY |
For Windows systems, this property sets the selection of components installed to core agent files only. |
MANUAL_SERVICE | SSMCONFIG.
MANUAL_SERVICE |
For Windows systems, this property registers Netcool/SSM service in manual mode and does not start it after installation. |
CLUSTER_INST | SSMCONFIG.
CLUSTER_INST |
For Windows systems, this property selects the cluster-aware installation mode for installing Netcool/SSM on a Windows server cluster node. |
CLUSTER_GROUP | SSMCONFIG.
CLUSTER_GROUP |
For Windows systems, this property specifies the name of the cluster group on which to install Netcool/SSM. |
CORE_CONFIG_DISK | SSMCONFIG.
CORE_CONFIG_DISK |
For Windows systems, this property specifies the name of the physical disk resource on which to install Netcool/SSM core configuration files. |
BYPASS_RECONFIG | SSMCONFIG.
BYPASS_RECONFIG |
For Windows systems, this property bypasses the installer configuration dialogs during an upgrade. |
AGENTLOG | SSMCONFIG.
AGENTLOG |
For UNIX® systems, this property specifies the path and filename of the agent log file. The default: agent.log. |
AGENTLOGSIZE | SSMCONFIG.
AGENTLOGSIZE |
For UNIX systems, this property specifies the maximum size of the agent log file (in bytes). The default: 1000000. |
SNMPTRAPVER | SSMCONFIG.
SNMPTRAPVER |
For UNIX systems, this property specifies the format of notifications sent by the agent: 1- SNMP v1 Trap or 2 - SNMPv2 Trap. The default: 1. |
CONFIGDIR | SSMCONFIG.
CONFIGDIR |
For UNIX systems, this property sets the agent configuration directory. The default: /opt/netcool/ssm/config. |
COEXIST | SSMCONFIG.
COEXIST |
For UNIX systems, this property specifies whether any existing Netcool/SSM installation in any path other than that indicated by INST_PATH is removed during installation. If you want to install Netcool/SSM in the same directory as the existing installation, specify n. This option is intended for testing multiple installations on one computer. The default: y. |
INST_CONSOLE | SSMCONFIG.
INST_CONSOLE |
For UNIX systems, this property selects whether the command console is installed: y - Command console installed and n - Command console not installed. The default: y. |
SERVER | SSMCONFIG.SERVER | Specify the hostname of the Tivoli® Enterprise Management Systems to run the command. If the server name specified is a remote monitoring server, the request is routed to the remote monitoring server to run. However, if the remote monitoring server is currently not connected to the hub monitoring server, the request is run at the hub monitoring server. The "TEMS Name" field of the output from the tacmd getdeploystatus command shows the monitoring server that the command is running. |
For information on RXA connection properties, see RXA connection properties.
[ Top of Page | Previous Page | Next Page ]