Remove the new Enclosure FRU from its packaging and install it
in onto the slide rails. Pull the slide rails forward 1 until
they click, twice, into place. Carefully lift the Enclosure FRU and
tilt it into position over the slide rails so that the rear posts 2 on
the Enclosure FRU line up with the rear slots 3 on
the slide rails. Slide the server down until the rear posts slip into
the two rear slots, and then slowly lower the front of the Enclosure
FRU 4 until the other posts slip into
the other slots on the slide rails. Make sure that the front latch 5 slides
over the posts.Figure 1. Install Enclosure FRU on Slide Rails
Note the location of the devices in the old 7226. Remove the Half
High Bay Blanks from those locations in the Enclosure FRU. To remove
the Half High Bay Blank, push the drive latch 1 toward
the Half High Bay Blank and begin to pull the blank out of the enclosure.
Grasp the Bay Blank 2 and pull it out
of the enclosure. Figure 2. Remove Half-High Bay Blanks
Remove the Tape Drives, RDX Docking stations, and Slim Drive Tray
Assemblies from the 7226. To remove the devices, push the drive latch 1 toward
the drive assembly and begin to pull the drive out of the enclosure.
Grasp the drive 2 and pull the assembly
out of the drive bay. Disconnect the cables 3 from
the drive assembly.
Note: Do not remove the DVD-Ram Drives or the re-driver
or converter cards from the Slim Drive Assemblies.
Figure 3. Removing a Drive Assembly
Install each device into Enclosure FRU into the its noted location.
To install the drive assemblies, attach the Drive Latch 1 to
the drive assembly 2 and insert both
into the drive bay until they click into place.Figure 4. Inserting a Drive
To remove the Top Cover of the Enclosure FRU, loosen the Top Cover
Thumb Screws 1.Figure 5. Top Cover Thumb Screws
Slide the Enclosure FRU Top Cover toward the rear of the enclosure 1 and
lift to remove 2.Figure 6. Top Cover
Note the location of each Interface Assembly in the 7226. To remove
each Interface assembly from the 7226, remove the Interface Assembly
from the drive connector 1 and remove
the power connector 2.Figure 7. Remove Interface Assembly
Note the locations of the Blank Back Plates to be removed
from the new Enclosure FRU. To remove a Blank Back Plate, pull the
back plate pin 1 to release the Blank
Back Plate, and remove the Blank Back Plate 2 from
the rear panel slot.Figure 8. Remove Blank Back Plate For a 7226 Storage Enclosure that
does not contain a Front USB port, go to step 14. For a
7226 Storage Enclosure installed in PureFlex systems with a Front
USB port, continue to step 11.
For the USB Interface (Front) Assembly
(PureFlex systems only), remove the Front USB bezel by pressing down
on the catch located on the top and bottom of the bezel. Remove the
USB Interface (Front) Assembly from the drive connector 1 and
remove the power connector 2.Figure 9. Remove USB Interface (Front) Assembly (PureFlex systems only)
Figure 10. Remove Interface Assembly (PureFlex systems only)
Insert the USB cable through the opening in the chassis
before snapping the bezel into place to attach the USB Interface (Front)
Assembly (only available on PureFlex systems).Figure 11. Insert the USB Interface (Front) Assembly (PureFlex systems only)
Attach the USB Interface (Front) Assembly (PureFlex systems
only) from the drive connector 1, and
attach the power connector 2.Figure 12. Attach USB Interface (Front) Assembly (PureFlex systems only)
Install each Interface Assembly into the
Enclosure FRU. Attach the Interface Assembly to the drive connector 1,
and attach the Power Connector 2. Attach
the power jumper 3. Figure 13. Attach Interface Assembly
To Insert the Interface Assembly into the rear panel slot, insert
the tab on the back plate into the indent in the back panel opening 1,
pull the pin on the back plate 2 and
push the back plate into the back panel opening 3 until
it clicks into place.Figure 14. Insert Interface Assembly Back Plate
Locate the repair identification (RID) tag (included with the
replacement Enclosure FRU). Write down the serial number of the failed
7226 Storage Enclosure unit on the RID Tag 1.
Affix the RID tag to the bottom of the replacement Enclosure FRU ,
as close as possible, but not covering the serial number of the replacement
enclosure 2.Figure 15. RID Tag
