PIOCARD

The multi-adapter bridge hardware that controls PCI adapters and PCI card slots detected an error.

1. Does the reference code start with B7xx?
   • Yes: Perform the following:
     1. Record the DSA, which is word 7 of the reference code.
     2. Locate the card specified in the DSA by going to MABIP53. Return here after locating the FRU and continue with the next step.
   • No: Continue with the next step..
2. Are you working from the serviceable event view and a card location is listed with this FRU?
   • Yes: The error is located at the listed card location. Go to step 6.
   • No: Perform the following:
     1. Record the DSA, which is word 7 of the reference code.
     2. Locate the card specified in the DSA by going to MABIP53. Return here after locating the FRU and continue with the next step.
3. Did you identify a single FRU location by using MABIP53?
   • Yes: This is the location of the failing item. Go to step 6.
   • No: Continue with the next step.
4. Perform the following, referring to the remove and replace procedures for each FRU location you determined (you can find links to the locations information, and from there to the remove and replace procedures, in the table at the end of this procedure):
   1. Remove all of the adapter and/or IOP cards in the locations that are identified in the given range of card slots. Do not remove any FRUs with embedded adapters, only FRUs in PCI card slots.
   2. Replace each card one at a time.
      Note: For i5/OS® adapters controlled by IOPs, replace the IOP before any of the adapters.
      Power on the unit (as instructed in the remove and replace procedure indicated by following the link in the following table) after you replace each card until either the problem reappears or you have replaced each card.
   3. Did the problem reappear?
      • Yes: The last card that you replaced before the problem appeared again is the failing item. This ends the procedure.
      • No: Continue with the next step.
5. Did you identify a FRU with embedded adapters when performing MABIP53?
   • Yes: The problem is in the FRU with the embedded adapter. Continue with the next step and exchange that FRU.
   • No: The problem may be intermittent. Contact your next level of support. This ends the procedure.
6. Use the links in the table below to locate and replace the failing item(s).

   Table 1. Failing item for symbolic FRU PIOCARD

   System model, expansion unit, or machine type	Name of FRU to exchange	FRU location	Link to locations information
   505	PCIX adapter card	-P1-C12-C1 -P1-C13-C1	Locations — model 505
   	Embedded adapters in system unit logic planar, PCI bridge set 0	P1
   510 and OpenPower® 710	PCI IOP or IOA card in PCI bridge set 0	-P2-C1 -P2-C2 -P2-C3	Locations — model 510 and OpenPower 710
   	Embedded adapters in system unit logic planar, PCI bridge sets 1 and 2	-P1
   515, 520, 525	Embedded adapters in system unit logic planar, PCI bridge sets 1 and 2	-P1-C1 -P1-C2 -P1-C4	Locations — model 515, 520, 525
   	PCI IOP or IOA card in PCI bridge set 2	-P1-C3 -P1-C5 -P1-C6
   	Embedded adapters in system unit logic planar, PCI bridge sets 1 and 2	-P1
   550 and OpenPower 720	PCI IOP or IOA card in PCI bridge set 1	-P1-C1 -P1-C2	Locations — OpenPower 720 and model 550
   	PCI IOP or IOA card in PCI bridge set 2	-P1-C3 -P1-C4 -P1-C5
   	Embedded adapters in system unit logic planar, PCI bridge sets 1 and 2	-P1
   570	PCI IOP or IOA card in PCI bridge set 2	-P1-C1 -P1-C2	Locations — model 570
   	PCI IOP or IOA card in PCI bridge set 3	-P1-C3 -P1-C4 -P1-C5 -P1-C6
   	Embedded adapters in system unit logic planar, PCI bridge sets 1, 2, and 3	-P1
   5074, 8079-002, 8093-002	PCI IOP or IOA in PCI bridge set 1	C01 C02 C03 C04	Locations — 5074, 8079-002, and 8093-002 expansion units
   	PCI IOP or IOA in PCI bridge set 2	C05 C06 C07 C09 C10
   	PCI IOP or IOA in PCI bridge set 3	C11 C12 C13 C14 C15
   5079	PCI IOP or IOA in PCI bridge set 1	C01 C02 C03 C04	Locations — 5079 expansion unit
   	PCI IOP or IOA in PCI bridge set 2	C05 C06 C07 C09 C10
   	PCI IOP or IOA in PCI bridge set 3	C11 C12 C13 C14 C15
   5088, 0588	PCI IOP or IOA in PCI bridge set 1	C01 C02 C03 C04	Locations — 5088 and 0588 expansion units
   	PCI IOP or IOA in PCI bridge set 2	C05 C06 C07 C08 C09
   	PCI IOP or IOA in PCI bridge set 3	C11 C12 C13 C14 C15
   5094, 5294, 8094-002	PCI IOP or IOA in PCI bridge set 1	C01 C02 C03 C04	Locations — 5094, 5294, and 8094-002 expansion units
   	PCI IOP or IOA in PCI bridge set 2	C05 C06 C07 C08 C09
   	PCI IOP or IOA in PCI bridge set 3	C11 C12 C13 C14 C15
   5095, 0595	PCI IOP or IOA in PCI bridge set 1	C01 C02 C03 C04	Locations — 5095 and 0595 expansion units
   	PCI IOP or IOA in PCI bridge set 2	C06 C07 C08
   Type 1519 — external xSeries® server	Integrated xSeries adapter card	Follow RIO/HSL cable	Locations — Integrated xSeries adapter card (IXA)
   7311-D10, 7311-D11, and 5790	PCI IOP or IOA in PCI bridge set 1	-P1-I1 -P1-I2 -P1-I3	Locations — 7311-D10, 7311-D11, and 5790 expansion units
   	PCI IOP or IOA in PCI bridge set 2	-P1-I4 -P1-I5 -P1-I6
   5791, 5794, and 7040-7040-61D	PCI IOP or IOA in PCI bridge set 1	-P1-I1 -P1-I2 -P1-I3 -P1-I4	Locations — 5791, 5794, and 7040-7040-61D expansion unit
   	PCI IOP or IOA in PCI bridge set 2	-P1-I5 -P1-I6 -P1-I7
   	PCI IOP or IOA in PCI bridge set 3	-P1-I8 -P1-I9 -P1-I10
   	Embedded adapters in I/O unit logic planar (left side), PCI bridge sets 2 and 3	-P1
   	PCI IOP or IOA in PCI bridge set 1	-P2-I1 -P2-I2 -P2-I3 -P2-I4
   	PCI IOP or IOA in PCI bridge set 2	-P2-I5 -P2-I6 -P2-I7
   	PCI IOP or IOA in PCI bridge set 3	-P2-I8 -P2-I9 -P2-I10
   	Embedded adapters in I/O unit logic planar (right side), PCI bridge sets 2 and 3	-P2