“In times of universal deceit, telling the truth will be a revolutionary act.”
-- George Orwell
Well, it has been over two years since I first covered IBM's acquisition of the XIV company. Amazingly, I still see a lot of misperceptions out in the blogosphere, especially those regarding double drive failures for the XIV storage system. Despite various attempts to [explain XIV resiliency] and to [dispel the rumors], there are still competitors making stuff up, putting fear, uncertainty and doubt into the minds of prospective XIV clients.
Clients love the IBM XIV storage system! In this economy, companies are not stupid. Before buying any enterprise-class disk system, they ask the tough questions, run evaluation tests, and all the other due diligence often referred to as "kicking the tires". Here is what some IBM clients have said about their XIV systems:
“3-5 minutes vs. 8-10 hours rebuild time...”
-- satisfied XIV client
“...we tested an entire module failure - all data is re-distributed in under 6 hours...only 3-5% performance degradation during rebuild...”
-- excited XIV client
“Not only did XIV meet our expectations, it greatly exceeded them...”
-- delighted XIV client
In this blog post, I hope to set the record straight. It is not my intent to embarrass anyone in particular, so instead will focus on a fact-based approach.
- Fact: IBM has sold THOUSANDS of XIV systems
XIV is "proven" technology with thousands of XIV systems in company data centers. And by systems, I mean full disk systems with 6 to 15 modules in a single rack, twelve drives per module. That equates to hundreds of thousands of disk drives in production TODAY, comparable to the number of disk drives studied by [Google], and [Carnegie Mellon University] that I discussed in my blog post [Fleet Cars and Skin Cells].
- Fact: To date, no customer has lost data as a result of a Double Drive Failure on XIV storage system
This has always been true, both when XIV was a stand-alone company and since the IBM acquisition two years ago. When examining the resilience of an array to any single or multiple component failures, it's important to understand the architecture and the design of the system and not assume all systems are alike. At it's core, XIV is a grid-based storage system. IBM XIV does not use traditional RAID-5 or RAID-10 method, but instead data is distributed across loosely connected data modules which act as independent building blocks. XIV divides each LUN into 1MB "chunks", and stores two copies of each chunk on separate drives in separate modules. We call this "RAID-X".
Spreading all the data across many drives is not unique to XIV. Many disk systems, including EMC CLARiiON-based V-Max, HP EVA, and Hitachi Data Systems (HDS) USP-V, allow customers to get XIV-like performance by spreading LUNs across multiple RAID ranks. This is known in the industry as "wide-striping". Some vendors use the terms "metavolumes" or "extent pools" to refer to their implementations of wide-striping. Clients have coined their own phrases, such as "stripes across stripes", "plaid stripes", or "RAID 500". It is highly unlikely that an XIV will experience a double drive failure that ultimately requires recovery of files or LUNs, and is substantially less vulnerable to data loss than an EVA, USP-V or V-Max configured in RAID-5. Fellow blogger Keith Stevenson (IBM) compared XIV's RAID-X design to other forms of RAID in his post [RAID in the 21st Centure].
- Fact: IBM XIV is designed to minimize the likelihood and impact of a double drive failure
The independent failure of two drives is a rare occurrence. More data has been lost from hash collisions on EMC Centera than from double drive failures on XIV, and hash collisions are also very rare. While the published worst-case time to re-protect from a 1TB drive failure for a fully-configured XIV is 30 minutes, field experience shows XIV regaining full redundancy on average in 12 minutes. That is 40 times less likely than a typical 8-10 hour window for a RAID-5 configuration.
A lot of bad things can happen in those 8-10 hours of traditional RAID rebuild. Performance can be seriously degraded. Other components may be affected, as they share cache, connected to the same backplane or bus, or co-dependent in some other manner. An engineer supporting the customer onsite during a RAID-5 rebuild might pull the wrong drive, thereby causing a double drive failure they were hoping to avoid. Having IBM XIV rebuild in only a few minutes addresses this "human factor".
In his post [XIV drive management], fellow blogger Jim Kelly (IBM) covers a variety of reasons why storage admins feel double drive failures are more than just random chance. XIV avoids load stress normally associated with traditional RAID rebuild by evenly spreading out the workload across all drives. This is known in the industry as "wear-leveling". When the first drive fails, the recovery is spread across the remaining 179 drives, so that each drive only processes about 1 percent of the data. The [Ultrastar A7K1000] 1TB SATA disk drives that IBM uses from HGST have specified 1.2 million hours mean-time-between-failures [MTBF] would average about one drive failing every nine months in a 180-drive XIV system. However, field experience shows that an XIV system will experience, on average, one drive failure per 13 months, comparable to what companies experience with more robust Fibre Channel drives. That's innovative XIV wear-leveling at work!
- Fact: In the highly unlikely event that a DDF were to occur, you will have full read/write access to nearly all of your data on the XIV, all but a few GB.
Even though it has NEVER happened in the field, some clients and prospects are curious what a double drive failure on an XIV would look like. First, a critical alert message would be sent to both the client and IBM, and a "union list" is generated, identifying all the chunks in common. The worst case on a 15-module XIV fully loaded with 79TB data is approximately 9000 chunks, or 9GB of data. The remaining 78.991 TB of unaffected data are fully accessible for read or write. Any I/O requests for the chunks in the "union list" will have no response yet, so there is no way for host applications to access outdated information or cause any corruption.
(One blogger compared losing data on the XIV to drilling a hole through the phone book. Mathematically, the drill bit would be only 1/16th of an inch, or 1.60 millimeters for you folks outside the USA. Enough to knock out perhaps one character from a name or phone number on each page. If you have ever seen an actor in the movies look up a phone number in a telephone booth then yank out a page from the phone book, the XIV equivalent would be cutting out 1/8th of a page from an 1100 page phone book. In both cases, all of the rest of the unaffected information is full accessible, and it is easy to identify which information is missing.)
If the second drive failed several minutes after the first drive, the process for full redundancy is already well under way. This means the union list is considerably shorter or completely empty, and substantially fewer chunks are impacted. Contrast this with RAID-5, where being 99 percent complete on the rebuild when the second drive fails is just as catastrophic as having both drives fail simultaneously.
- Fact: After a DDF event, the files on these few GB can be identified for recovery.
Once IBM receives notification of a critical event, an IBM engineer immediately connects to the XIV using remote service support method. There is no need to send someone physically onsite, the repair actions can be done remotely. The IBM engineer has tools from HGST to recover, in most cases, all of the data.
Any "union" chunk that the HGST tools are unable to recover will be set to "media error" mode. The IBM engineer can provide the client a list of the XIV LUNs and LBAs that are on the "media error" list. From this list, the client can determine which hosts these LUNs are attached to, and run file scan utility to the file systems that these LUNs represent. Files that get a media error during this scan will be listed as needing recovery. A chunk could contain several small files, or the chunk could be just part of a large file. To minimize time, the scans and recoveries can all be prioritized and performed in parallel across host systems zoned to these LUNs.
As with any file or volume recovery, keep in mind that these might be part of a larger consistency group, and that your recovery procedures should make sense for the applications involved. In any case, you are probably going to be up-and-running in less time with XIV than recovery from a RAID-5 double failure would take, and certainly nowhere near "beyond repair" that other vendors might have you believe.
- Fact: This does not mean you can eliminate all Disaster Recovery planning!
To put this in perspective, you are more likely to lose XIV data from an earthquake, hurricane, fire or flood than from a double drive failure. As with any unlikely disaster, it is best to have a disaster recovery plan than to hope it never happens. All disk systems that sit on a single datacenter floor are vulnerable to such disasters.
For mission-critical applications, IBM recommends using disk mirroring capability. IBM XIV storage system offers synchronous and asynchronous mirroring natively, both included at no additional charge.
For more about IBM XIV reliability, read this whitepaper [IBM XIV© Storage System: Reliability Reinvented]. To find out why so many clients LOVE their XIV, contact your local IBM storage sales rep or IBM Business Partner.
technorati tags: IBM, XIV, DDF, RAID-5, RAID-10, RAID-X, RAID-6, RAID-DP, HP, EVA, HDS, USP-V, EMC, CLARiiON, V-Max, Disaster Recovery, HGST, UltraStar, A7K1000