Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Tony Pearson is a Master Inventor and Senior Software Engineer for the IBM Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2016, Tony celebrates his 30th year anniversary with IBM Storage. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services. You can also follow him on Twitter @az990tony.
(Short URL for this blog: ibm.co/Pearson
Full VMware Vstorage API for Array Integration (VAAI). Back in 2008, VMware announced new vStorage APIs for its vSphere ESX hypervisor: vStorage API for Site Recovery Manager, vStorage API for Data Potection, vStorage API for Multipathing. Last July, VMware added a new API called vStorage API for Array Integration [VAAI] which offers three primitives:
Hardware-assisted Blocks zeroing. Sometimes referred to as "Write Same", this SCSI command will zero out a large section of blocks, presumably as part of a VMDK file. This can then be used to reclaim space on the XIV on thin-provisioned LUNs.
Hardware-assisted Copy. Make an XIV snapshot of data without any I/O on the server hardware.
Hardware-assisted locking. On mainframes, this is call Parallel Access Volumes (PAV). Instead of locking an entire LUN using standard SCSI reserve commands, this primitive allows an ESX host to lock just an individual block so as not to interfere with other hosts accessing other blocks on that same LUN.
Quality of Service (QoS) Performance Classes.
When XIV was first released, it treated all hosts and all data the same, even when deployed for a variety of different applications. This worked for some clients, such as [Medicare y Mucho Más]. They migrated their databases, file servers and email system from EMC CLARiiON to an IBM XIV Storage System. In conjunction with VMware, the XIV provides a highly flexible and scalable virtualized architecture, which enhances the company's business agility.
However, other clients were skeptical, and felt they needed additional "nobs" to prioritize different workloads. The new 10.2.4 microcode allows you to define four different "performance classes". This is like the door of a nightclub. All the regular people are waiting in a long line, but when a celebrity in a limo arrives, the bouncer unclips the cord, and lets the celebrity in. For each class, you provide IOPS and/or MB/sec targets, and the XIV manages to those goals. Performance classes are assigned to each host based on their value to the business.
Offline Initialization for Asynchronous Mirror.
Internally, we called this Truck Mode. Normally, when a customer decides to start using Asynchronous Mirror, they already have a lot of data at the primary location, and so there is a lot of data to send over to the new XIV box at the secondary location. This new feature allows the data to be dumped to tape at the primary location. Those tapes are shipped to the secondary location and restored on the empty XIV. The two XIV boxes are then connected for Asynchronous Mirroring, and checksums of each 64KB block are compared to determine what has changed at the primary during this "tape delivery time". This greatly reduces the time it takes for the two boxes to get past the initial synchronization phase.
IP-based Replication. When IBM first launched the Storwize V7000 last October, people commented that the one feature they felt missing was IP-based replication. Sure, we offered FCP-based replication as most other Enterprise-class disk systems offer today, but many midrange systems also offer IP-based repliation to reduce the need for expensive FCIP routers. [IBM Tivoli Storage FastBack for Storwize V7000] provides IP-based replication for Storwize V7000 systems.
Network Attached Storage
IBM announced two new models of the IBM System Storage N series. The midrange N6240 supports up to 600 drives, replacing the N6040 system. The entry-level N6210 supports up to 240 drives, and replaces the N3600 system. Details for both are available on the latest [data sheet].
IBM Real-Time Compression appliances work with all N series models to provide additional storage efficiency. Last October, I provided the [Product Name Decoder Ring] for the STN6500 and STN6800 models. The STN6500 supports 1 GbE ports, and the STN6800 supports 10GbE ports (or a mix of 10GbE and 1GbE, if you prefer). The IBM versions of these models were announced last December, but some people were on vacation and might have missed it. For more details of this, read the [Resources page], the [landing page], or [watch this video].
IBM System Storage DS3000 series
IBM System Storage [DS3524 Express DC and EXP3524 Express DC] models are powered with direct current (DC) rather than alternating current (AC). The DS3524 packs dual controllers and two dozen small-form factor (2.5 inch) drives in a compact 2U-high rack-optimized module. The EXP3524 provides addition disk capacity that can be attached to the DS3524 for expansion.
Large data centers, especially those in the Telecommunications Industry, receive AC from their power company, then store it in a large battery called an Uninterruptible Power Supply (UPS). For DC-powered equipment, they can run directly off this battery source, but for AC-powered equipment, the DC has to be converted back to AC, and some energy is lost in the conversion. Thus, having DC-powered equipment is more energy efficient, or "green", for the IT data center.
Whether you get the DC-powered or AC-powered models, both are NEBS-compliant and ETSI-compliant.
New Tape Drive Options for Autoloaders and Libraries
IBM System Storage [TS2900 Autoloader] is a compact 1U-high tape system that supports one LTO drive and up to 9 tape cartridges. The TS2900 can support either an LTO-3, LTO-4 or LTO-5 half-height drive.
IBM System Storage [TS3100 and TS3200 Tape Libraries] were also enhanced. The TS3100 can accomodate one full-height LTO drive, or two half-height drives, and hold up to 24 cartridges. The TS3200 offers twice as many drives and space for cartridges.
Continuing my discussion of this week's announcements of IBM storage products, I will cover the announcements that double storage capacity per footprint.
Linear Tape Open - Generation 5
IBM announced [LTO-5 drives], the TS2250 half-height and the TS2350 full-height drives, as well as support for LTO-5 drives in its various tape libraries: TS3100, TS3200, and TS3500. The native 1.5TB capacity of the LTO-5 cartridge is nearly double the 800GB capacity of the LTO-4 predecessor. With 2:1 compression, that's 3TB of data per cartridge! Performance-wise, the data transfer rate is 140 MB/sec, about 17 percent improvement over the 120MB/sec of the LTO-4 technology. The TS2250, TS2350, TS3100 and TS3200 now all offer dual-SAS ports for higher availability.
LTO-5 carries forward many of the advancements of past generations. For example, LTO-5 continues the G-2/G-1 "backward compatibility" architecture, which means that the LTO-5 drive can read LTO-3 and LTO-4 cartridges, and can write LTO-4 cartridges. Like the LTO-3 and LTO-4, the same LTO-5 drive can read and write WORM or regular rewriteable cartridges. Like the LTO-4, the LTO-5 offers drive-level data-at-rest encryption. These use a symmetric 256-bit AES key, managed by IBM Tivoli Key Lifecycle Manager (TKLM).
One thing that is new in LTO-5 is the Long Term File System [LTFS] available on the TS2250 and TS2350, which allows you to treat the tape as a hierarchical file system, with files and folders, that you can drag and drop like any other file system.
XIV storage system
IBM [doubles the capacity of the XIV storage system] by supporting 2TB SATA drives. A full 15-module frame can hold up to 161TB of usable capacity. The smallest 6-module system with 2TB can hold up to 55TB of usable capacity. At this time, all of the drives in an XIV must be the same type, so we do not yet allow intermix of 1TB and 2TB in the same frame. The 2TB are more energy efficient, with a full 15-module frame consuming on average 6.7 kVA, compared to 7.8 kVA for the 1TB drives. The performance is roughly the same, so if, for example, your application workload got 3700 IOPS per module with 1TB drives, it will get about the same 3700 IOPS per module with 2TB drives.
The EXN1000 and EXN3000 can now double in capacity with 2TB SATA drives. These can be attached to the N3000 entry-level models, such as the N3400.
DS3000 disk system
The DS3200, DS3300 and DS3400, as well as their related expansion drawers, now supports 2TB SATA drives. This means that a single control unit with three expansion drawers can hold up to 96TB of raw capacity (48 drives).
DS8700 disk system
The DS8700 also now supports 2TB SATA drives, for a maximum raw capacity over 2PB, as well as new 600GB Fibre Channel drives. Now that IBM offers [Easy Tier] functionality, pairing Solid State Drives with slower, energy-efficient SATA disk makes a lot of financial sense.
That's a lot of announcements! As always, feel free to dig into each of the links to learn more about each product.
Well, it's Tuesday again, and you know what that means! IBM Announcements!
Today also happens to be [Election Day] in the United States, and some have questioned IBM's logic of making major storage announcements on Election Day. During the campaigns, a major theme was to help Small and Medium size businesses, because these are the engines of economic growth and improved employment.
Hopefully, you all saw today's Launch Webcast on these announcements, but in case you missed it, waiting in line at the polling station to cast your vote, or caught without electricity or Internet access from [Superstorm Sandy], it is now available [On-Demand].
The 2U control enclosure can have up to four additional 2U expansion enclosures, for a maximum of 120 drives, or 180TB of raw disk capacity. Like the Storwize V7000, the Storwize V3700 supports a [large number of servers and operating systems.]
Many of the features you already know from the Storwize V7000 are carried forward:
1GbE iSCSI + 8GbFC
8GbFC, 10GbE iSCSI/FCoE, Statement of Direction for 6Gb SAS
8GB per canister
4GB per canister, upgradeable to 8GB
Up to 4 control enclosures in a clustered system, each with up to 9 expansion enclosures
Up to 4 expansion enclosures
Maximum Number of drives/TB
Up to 120 drives/180TB
RAID levels supported
GUI, CLI, SMI-S API
GUI, CLI, SMI-S API
Internal (included), external (optional)
Internal only (included)
Non-disruptive data migration
One-directional (migrate to Storwize V3700, included)
Statement of direction
Up to 256 targets (included)
Up to 64 targets (included) Statement of Direction for optional 2,040 targets
Metro Mirror and Global Mirror (optional)
Statement of Direction (optional)
The IBM Storwize V3700 is offered at attractive leasing options through IBM Global Financing.
IBM LTO-6 drives and midrange tape libraries
Last month, IBM's [Tape and Storage Hypervisor Announcements] included LTO-6 for the enterprise-class TS3500 tape library. Today, the LTO-6 support is complete with support for midrange tape drives and libraries.
There are two tape drive models. The TS2260 is based on the half-height drive, intended for occasional 9-to-5 usage. The TS2360 is based on the full-height drive, intended for 24x7 access. These drives can read LTO-4 and LTO-5 tape cartridge media, and can write LTO-5 cartridge media. The new LTO-6 tape cartridge media is expected to be available next month.
In addition to the IBM TS3500 Enterprise Tape Library, LTO-6 is now supported on all of the midrange tape libraries: TS2900, TS3100, TS3200 and TS3310.
IBM Linear Tape File System Library Edition V2.1.2
There are two levels of [Linear Tape File System], or LTFS for short. The first is the Single Drive Edition (LTFS-SDE), which allows you to attach an LTO-5, LTO-6 or TS1140 tape drive to a single workstation, and allow you to mount tape cartridges as easy as mounting USB memory sticks. This presents a full file system view that allows you to read, edit, create, and even drag-and-drop files to other file systems. The LTFS-SDE driver is available for Windows, Linux, and Mac OS.
The second is the Library Edition (LTFS-LE), which allows you to mount the entire tape library as a file system. Each tape cartridge in the library is presented as a subdirectory folder, that you can access like any file system on disk. This was only available for Linux systems, which could then export the files through NFS, FTP or HTTP protocols to other clients. Now, with release v2.1.2, LTFS-LE supports Windows servers, so that you can share the files with other clients through CIFS as well.