Safe Harbor Statement: The information on IBM products is intended to outline IBM's general product direction and it should not be relied on in making a purchasing decision. The information on the new products is for informational purposes only and may not be incorporated into any contract. The information on IBM products is not a commitment, promise, or legal obligation to deliver any material, code, or functionality. The development, release, and timing of any features or functionality described for IBM products remains at IBM's sole discretion.
Tony Pearson is a an active participant in local, regional, and industry-specific interests, and does not receive any special payments to mention them on this blog.
Tony Pearson receives part of the revenue proceeds from sales of books he has authored listed in the side panel.
Tony Pearson is not a medical doctor, and this blog does not reference any IBM product or service that is intended for use in the diagnosis, treatment, cure, prevention or monitoring of a disease or medical condition, unless otherwise specified on individual posts.
Tony Pearson is a Master Inventor and Senior IT Specialist for the IBM System Storage product line at the
IBM Executive Briefing Center in Tucson Arizona, and featured contributor
to IBM's developerWorks. In 2011, Tony celebrated his 25th year anniversary with IBM Storage on the same day as the IBM's Centennial. He is
author of the Inside System Storage series of books. This blog is for the open exchange of ideas relating to storage and storage networking hardware, software and services. You can also follow him on Twitter @az990tony.
(Short URL for this blog: ibm.co/Pearson
Well, we had another successful event in Second Life today.
Unlike our April 26 launch of our System Storage products for IBM Business Partners only, this time we decided this time to make it as a "Meet the Storage Experts" Q&A Panel format, and open up registration to everyone. Thesubject matter experts sat at the front of the room on four stools. We had six rows of chairs arrangedsemi-circularly.
Shown above, from left to right, are the avatars of our four experts:
IBM System Storage N series, focusing on recent N3000 disk system announcements
Harold Pike (holding the microphone while speaking)
IBM System Storage DS3000 and DS4000 series, focusing on recent DS3000 disk system announcements
IBM System Storage TS series, focusing on recent TS2230, TS3400 and TS7700 tape system announcements
IBM storage networking, focusing on recent IBM SAN256B director blade announcements
While Eric was a veteran Second Lifer, having presented at our April event, the other three were trainedon how to raise their hand, speak into the microphone, sit on the stool, and so on. I want to thank allof our experts for putting in this effort!
The event was produced by Katrina H Smith. She did a great job, and made sure we were on top ofall the issues and tasks required to get the job done. Running a Second Life event is every bit ashard as running a real face-to-face event. We had several meetings to discuss venue details, placementof chairs, placement of product demos, audio/video recording, wall decorations, tee-shirt and coffee mug design, logistics, and so on.
I acted as moderator/emcee for the event. That is my back in the picture above. The process wassimple, modeled after the "Birds of a Feather" sessions at events like SHARE and the IBMStorage and Storage Networking Symposium. We threw out a list of topics the experts would cover,and people in the audience would "raise their left hand". I, as the moderator, would then walkover to each person, and hold out the microphone for them to ask the question. I would then repeat the question and ask the appropriate expert to provide an answer. We defined gestures onhow to "raise hand" and "put hand down" that we gave to each registered participant.
We had four dedicated "camera-avatars" in world to capture both video and screenshots.Our video editors are now working to edit "highlight videos" that we can use at future events, for training materials, and for our internal "BlueTube" online video system.
The room was filled with examples of each of our products, made into 3D objects that were dimensionallycorrect, and "textured" with photographs of the actual products. If you click on an object, you get a "notecard" that provided more information. Special thanks to Scott Bissmeyer for making all of theseobjects for us.
We made posters of each expert and placed them in all four corners of the room. On the bottom of each coffee mug was a picture of each of the experts, and if you walked under each of the posters, you were"dispensed" a coffee mug matching the expert shown in the poster.Participants could "Collect all Four!" When you bring the coffee mug up to takea sip, the picture on the bottom of the mug is exposed for all to see.And as a final give-away to the audience, we made a variety of event tee-shirts and polo-shirts.
At the end of the session, we asked everyone to click on the "Survey" kiosk near the exit door. We askedsix simple questions using SurveyMonkey.com that took only a fewminutes to process. We found asking questions immediately at the end of the event was the best way tocapture this feedback.
From a "Green" perspective, we had people registered from the following countries: US, India, Mexico,Australia, United Kingdom, Brazil, Germany, Argentina, Chile, China, Canada, and Venezuela. Second Lifeallows all these people who probably could not travel, or could not afford the time and expense to travel,to participate in a simulated face-to-face meeting without energy consumption of traditional travel methods.
More importantly, we got several leads for business. People often ask "Yes, but is there any businessassociated with this?" This time, there was, based on the answers to the questions, several avatars asked for a real sales call to follow-up on the products and offerings they were discussed.
With such a great success, we have already scheduled our next Second Life event, November 8. Mark your calendars! I'll postmore details on the registration process of the November event when available.
With all the announcements we had in June, it is easy for some of the more subtle enhancements to get overlooked. While I was at Orlando for the IBM Edge conference, I was able to blog about some of the key featured announcements. Then, later, when I got back from Orlando to Tucson, I was able to then blog about [More IBM Storage Announcements]. For IBM's Scale-Out Network Attach Storage (SONAS), I had simply:
"SONAS v1.3.2 adds support for management by the newly announced IBM Tivoli Storage Productivity Center v5.1 release. Also, IBM now officially supports Gateway configurations that have the storage nodes connected to XIV or Storwize V7000 disk systems. These gateway configurations offer new flexible choices and options for our ever-expanding set of clients."
In my defense, IBM numbers its software releasees with version.release.modification, so 1.3.2 is Version 1, Release 3, Modification 2. Generally, modification announcements don't get much attention. The big announcement for v1.3.0 of SONAS happened last October, see my blog post [October 2011 Announcements - Part I] or
the nice summary post [IBM Scale-out Network Attached Storage 1.3.0] from fellow blogger Roger Luethy.
Here is a diagram showing the three configurations of SONAS.
I have covered the SONAS Appliance model in depth in previous blogs, with options for fast and slow disk speeds, choice of RAID protection levels, a collection of enterprise-class software features provided at no additional charge, and interfaces to support a variety of third party backup and anti-virus checking software.
The basics haven't changed. The SONAS appliance consists of 2 to 32 interface nodes, 2 to 60 storage nodes, and up to 7,200 disk drives. The maximum configuration takes up 17 frames and holds 21.6PB of raw disk capacity, which is about 17PB usable space when RAID6 is configured. An interface nodes has one or two hex-core processors with up to 144GB of RAM to offer up to 3.5GB/sec performance each. This makes IBM SONAS the fastest performing and most scalable disk system in IBM's System Storage product line.
I thought I would go a bit deeper on the gateway models. These models support up to ten storage nodes, organized in pairs. The key difference is that instead of internal disk controllers, the storage nodes connect to external disk systems. There is enough space in the base SONAS rack to hold up to six interface nodes, or you can add a second rack if you need more interface nodes for increased performance.
SONAS with XIV gateway
XIV offers a clever approach to storage that allows for incredibly fast access to data on relatively slow 7200 RPM drives. By scattering data across all drives and taking advantage of parallel processing, rebuild times for a failed 3TB drive are less than 75 minutes. Compare that to typical rebuild times for 3TB drives that could take as much as 9-10 hours under active I/O loads!
In the configuration, each pair of storage nodes can connect to external SAN Fabric switches that then connect to one or two XIV storage systems. How simple is that? These can be the original XIV systems that support 1TB and 2TB drives, or the new XIV Gen3 systems that support 400GB Solid-state drives (SSD) and 3TB spinning disk drives. In both cases, you can acquire additional storage capacity as little as 12 drives at a time (one XIV module holds 12 drives).
The maximum configuration of ten XIV boxes could hold 1,800 drives. At 3TB drive per drive, that would be 2.4PB usable capacity.
The SONAS with XIV gateway does not require the XIV devices to be dedicated for SONAS purposes. Rather, you can assign some XIV storage space for the SONAS, and the rest is available for other servers. In this manner, SONAS just looks like another set of Linux-based servers to the XIV storage system. This in effect gives you "Unified Storage", with a full complement of NAS protocols from the SONAS side (NFS, CIFS, FTP, HTTPS, SCP) as well as block-based protocols directly from the XIV (FCP, iSCSI).
SONAS with Storwize V7000 gateway
The other gateway offering is the SONAS with Storwize V7000. Like the SONAS with XIV gateway model, you connect a pair of SONAS storage nodes to 1 or 2 Storwize V7000 disk systems. However, you do not need a SAN Fabric switch in between. You can instead connect the SONAS storage nodes directly to the Storwize V7000 control enclosures.
To acquire additional storage capacity, you can purchase a single drive at a time. That's right. Not 12 drives, or 60 drives, at a time, but one at a time. The Storwize V7000 supports a wide range of SSD, SAS and NL-SAS drives at different sizes, speeds and capacities. The drives can be configured into various RAID protection levels: RAID 0, 1, 3, 5, 6 and 10.
Each Storwize V7000 control enclosure can have up to nine expansion drawers. If you choose the 2.5-inch 24-bay models, you can have up to 480 drives per storage node pair, for a total of 2,400 drives. If you choose the 3.5-inch 12-bay models, you can have up to 240 drives per node pair, 1,200 drives total. At 3TB per drive, this could be 3.6PB of raw capacity. The usable PB would depend on which RAID level you selected. Of course, you don't have to limit yourself all to one size or the other. Feel free to mix 2.5-inch and 3.5-inch drawers to provide different storage pool capabilities.
All three SONAS configurations support Active Cloud Engine. This is a collection of features that differentiate SONAS from the other scale-out NAS wannabees in the marketplace:
Policy-driven Data Placement -- Different files can be directed to different storage pools. You no longer have to associate certain file systems to certain storage technologies.
High-speed Scan Engine -- SONAS can scan 10 million files per minute, per node. These scans can be used to drive data migration, backups, expirations, or replications, for example. It is over 100 times faster than traditional walk-the-directory-tree approaches employed by other NAS solutions.
Policy-driven Migration -- You can migrate files from one storage pool to another, based on age, days since last reference, size, and other criteria. The files can be moved from disk to disk, or move out of SONAS and stored on external media, such as tape or a virtual tape library. A lot of data stored on NAS systems is dormant, with little or no likelihood of being looked at again. Why waste money keeping that kind of data on expensive disk? With SONAS, you can move those files to tape can save lots of money. The files are stubbed in the SONAS file system, so that an access request to a file will automatically trigger a recall to fetch the data from tape back to the SONAS system.
Policy-driven Expiration -- SONAS can help you keep your system clean, by helping you decide what files should be deleted. This is especially useful for things like logs and traces that tend to just hang around until some deletes them manually.
WAN Caching -- This allows one SONAS to act as a "Cloud Storage Gateway" for another SONAS at a remote location connected by Wide Area Network (WAN). Let's say your main data center has a large SONAS repository of files, and a small branch office has a smaller SONAS. This allows all locations to have a "Global" view of the all the interconnected SONAS systems, with a high-speed user experience for local LAN-based access to the most recent and frequently used files.
If you want to learn more, see the [IBM SONAS landing page]. Next week, I will be across the Pacific Ocean in [Taipei], to teach IBM Top Gun class to sales reps and IBM Business Partners. "Selling SONAS" will be one of the topics I will be covering!
Ten years ago, I travelled to New York City with my colleague, Randy Fleenor, to present the latest in IBM tape technology for the 50th Anniversary. On Thursday evening that week, the latest movie in the Star Wars saga, Episode II: Attack of the Clones was just released, and it was being shown using the new Digital Light Projection (DLP) technology just around the corner at the Ziegfeld theater! This movie was the first live-action film to be filmed entirely digital. George Lucas saw that digital video was the future, and started the process moving forward with this film.
I convinced Randy to join me, and we arrived at 11:10pm, the movie was scheduled to start at 11pm, so we figured we had only missed a few previews. We walked into a completely empty lobby. I asked for two tickets for the 11pm show at the ticket counter, and was told it was all sold out, and there was a huge line around the building for all the people waiting to see the 1:00am show, and that we might get in to see the 3:00am show.
Randy and I had meetings on Friday morning, so we were not going to wait in line all night to see a 3am show! Just then, a young man comes out of the theater. He said his girlfriend can't make it, and wanted a refund for his two tickets. I pulled out a twenty-dollar bill, offered to buy them directly at face value, and the theater employees approved the transaction. The seats were front row of the balcony section. By then we had missed all the previews and a short bit of the movie, but that was alright with us.
(FTC Disclosure: I am both an employee and stockholder in IBM. The U.S. Federal Trade Commission may consider this a paid, celebrity endorsement of LTO-5 tapes and the LTFS technology. References to other companies are for illustrative purposes and do not represent an endorsement of their products or services.)
Digital recording is ideal for all types of video, including movies, television, and commercial advertisements.
The latest excitement is over IBM's Linear Tape File System™ (LTFS), which IBM donated to the IT industry as open source so that everyone in the world can benefit. This allows tape cartridges to be treated like USB memory sticks, the ultimate in portability of data. It is supported for Windows, Mac OS, and Linux, and already well embraced by the Media-and-Entertainment (M&E) industry.
"The move to IBM technology has helped the network shrink its archive from 1,507 to just 388 square feet, representing dramatic systems and energy-cost savings."
"AlphaTV has been broadcasting since 1996, creating and storing all forms of video entertainment, from soap operas and documentaries, to movies and sporting events, and creating a vast video archive along the way. Initially, AlphaTV archived its programming on Sony Beta SP format video cassettes that stored up to 90 minutes of content. Not long after, in need of storage that offered greater density, it turned to DVCPRO format videos that stored up to 120 minutes. But even that format was not allowing the network to keep pace with its ballooning archive, a storage infrastructure that by 2011 spanned more than 1,507 square feet."
"'A Greek TV series stored on 100 DVCPRO tapes took up four shelves in our library, whereas on LTO-5 cartridge now takes up the space of a deck of playing cards,' Constantinos Colombus, chief technology officer at AlphaTV, said in a statement."
"IBM LTFS, an intuitive and graphical file system that provides direct access to data on LTO 5 drives, has enabled AlphaTV to manage, move and share video files much like they can with disk-management systems, by simply dragging and dropping. As a result, file management is easier to do and far more efficient, said Colombus."
To prepare for this anniversary, I spoke with Brad Johns, of [Brad Johns Consulting]. Brad was head of IBM tape marketing for a while, and ran tape customer councils to gather feedback from our largest customers. Brad was my mentor in marketing at IBM from 2003-2007 and has since retired from IBM to start his own consulting practice.
The comparison was made between Crossroad Systems' Strongbox® with Enterprise tape library, LTO-5 tapes using LTFS, versus a unified disk storage system offering NAS protocols on high-capacity 3TB drives. The findings: the tape-based archive had nearly 80 percent lower TCO than the disk-based solution!
You don't have to be in the middle of the Greek economy to real that is a good value!
Last week, on January 31, two of my colleagues retired from IBM. At IBM, retirements always happen on the last day of the month. Here is my memories of each, listed alphabetically by last name.
Mark Doumas retires after working 32 years with IBM. Mark was my manager for a few months in 2003. Back then, IBM was working on launching a variety of new products, including the IBM SAN File System (SFS), the IBM SAN Volume Controller (SVC), a new release of Tivoli Storage Manager (TSM), and TotalStorage Productivity Center (TPC), which was later renamed to IBM Tivoli Storage Productivity Center.
Mark was manager of the portfolio management team, and I was asked to manage the tape systems portfolio. I am no stranger to tape, as one of my 19 patents is for the pre-migration feature of the IBM 3494 Virtual Tape Server (VTS). The portfolio included LTO and Enterprise tape drives, tape libraries and virtual tape systems. My job was to help decide how much of IBM's money we should invest in each product area. This was less of a technical role, and more of a business-oriented project management position
Portfolio management is actually part of a chain of project management roles. At the lowest level are team leads that manage individual features, referred to as line items of a release. Release managers are responsible for all the line items of a particular release. Product managers determine which line items will be shipped in which release, and often have to balance across three or more releases. Architects help determine which products in a portfolio should have certain features. Since I was chief architect for DFSMS and Productivity Center, stepping up to portfolio manager was naturally the next rung on the career ladder.
(Side note: If you were wondering why I was only a few months on the job, it was because I was offered an even better position as Technical Evangelist for SVC. See my 2007 blog post [The Art of Evangelism] for a humourous glimpse of the kind of trouble I got in with that title on my business card!)
While my stint in this role was brief, I am still considered an honorary member of the tape development team. Nearly every week I present an overview of our tape systems portfolio at the Tucson Executive Briefing Center, or on the road at conferences and marketing events.
This year, 2012, marks the 60th anniversary of IBM Tape, but I will save that for a future post!
Jim is an IBM Fellow for IBM Systems and Technology Group. There are only 73 IBM Fellows currently working for IBM, and this is the highest honor IBM can bestow on an employee. He has been working with IBM since 1968 and now retires after 44 years! Jim was tasked with predicting the future of IT, and help drive strategic direction for IBM. Cost pressures, requirements for growth, accelerating innovation and changing business needs help influence this direction.
Many consider Jim one of the fathers of server virtualization. For those who think VMware invented the concept of running multiple operating systems on a single host machine, guess again! IBM developed the first server hypervisor in 1967, and introduced the industry's first [offical VM product on August 2, 1972] for the mainframe.
When I joined IBM in 1986, my first job was to work on what was then called DFHSM software for the MVS operating system. Each software engineer had unlimited access to his or her own VM instance of a mainframe for development and testing. This was way better than what we had in college, having to share time on systems for only a few minutes or hours per day. Today, DFHSM is now called the DFSMShsm component of DFSMS, an element of the z/OS operating system.
At various conferences like [SHARE] and [WAVV] we celebrated VM's 25th anniversary in 1997, and its 30th anniversary in 2002. Today, it is called z/VM and IBM continues to invest in its future. Last October, IBM announced [z/VM 6.2] release which provides Live Guest Relocation (LGR) to seemlessly move VM guest images from one mainframe to another, similar to PowerVM's Live Partition Mobility or VMware's VMotion.
Lately, it seems employees at other companies jump from job to job, and from employer to employer, on average every 4.1 years. According to [National Longitudinal Surveys] conducted by the [US. Government's Bureau of Labor Statistics], the average baby boomer holds 11 jobs. In contrast, it is quite common to see IBMers work the majority of their career at IBM.
The next time you have a tasty beverage in your hand, raise your glass! To Mark and Jim, you have earned our respect, and you both have certainly earned your retirement!
This week I was aboard the Queen Mary in Long Beach, California! This was a business event organized by [Key Info Systems], a valued IBM Business Partner. Key Info resells IBM servers, storage and switches.
The Queen Mary retired in 1967, and has been converted into a hotel and events venue. The locals just parked their car and walked on board, but I got to stay Tuesday through Thursday in one of the cabins. It was long and narrow, with round windows! There were four dials for the bathtub: Cold Salt, Hot Fresh, Cold Fresh, and Hot Salt.
Stepping on the boat was like walking back in time through history! If you decide to go see it, check out the [Art Deco bar at the front of the Promenade deck. The ship is still in the water, but is permanently docked. It is sectioned off to prevent the ocean waves from affecting it, so we did not have the nauseous moving back and forth normally associated with cruise ships.
(It is with a bit of irony that we are on the Queen Mary just days after the tragedy of the [Costa Concordia], the largest Italian cruise ship that ran aground near Isola de Giglio. The captain will have to explain how he [fell into a lifeboat] before he had a chance to wait for everyone else to get safely off the shipwreck. He was certainly no [Captain Sulley]! I am thankful that most of the 4,200 people survived the incident.)
Lief Morin, Founder and Chief Executive for Key Info Systems, kicked off the meeting with highlights of 2011 successes. I have known Lief for years, as Key Info comes to the Tucson EBC on a frequent basis. This event was designed to give his sellers an update of what is the latest for each product line, and what to look forward to in the next 12-18 months.
The next speaker was from Vision Solutions that provides High Availability solutions for IBM i on Power Systems. In 2010, their company nearly doubled in size with the acquisition of Double-Take, which provides data replication for x86 servers running Windows, Linux, VMware, Hyper-V and other hypervisors. The capabilities of Double-Take sounded similar to what IBM offers with [Tivoli Storage Manager FastBack] and [Tivoli Storage Manager for Virtual Environments].
Dinner at Sir Winston's
Rather than take the "Ghosts and Legends" tour, I opted for dinner at the Queen Mary's signature restaurant, Sir Winston's. This is a fancy place, so dress accordingly. If you want the Raspberry soufflé, order it early as it takes 30 minutes to prepare!
[Storwize V7000], including the new Storwize V7000 Unified configuration
Storage is an important part of the Key Info Systems revenue stream, so I was glad to have lots of questions and interactions from the audience.
Murder Mystery Dinner
The acting troupe from [Dinner Detective] put on quite the show for us! With all that is going on in the world, it is good to laugh out loud every now and then.
In other murder mystery dinners I have participated in, each person is assigned a "character" and given a script of what to say and when to say it. This was different, we got to pick our own characters. I chose "Doctor Watson", from the Sherlock Holmes series. Several attendees thought it was a double meaning with [IBM Watson], the computer that figured out the clues on Jeopardy! television game show, and has since been [put to work at Wellpoint] to help out the Healthcare industry.
After the "murder" happened, two actors portraying policemen selected members of the audience to answer questions. We didn't get a script of what to say, so everyone had to "ad lib". I was singled out as a suspect, and had fun playing along in character. One of the attendees afterwards said he was impressed that I was able to fabricate such amusing and elaborate responses to their personal and embarassing questions. As a public speaker for IBM, I have had a lot of practice thinking quickly on my feet.
Fibre Channel and Ethernet Switches
The next two speakers gave us an update on Fibre Channel and Ethernet switches, and their thoughts on the inevitability of Fibre Channel over Ethernet (FCoE). One of the exciting new developments is the [Brocade Network Subscription] which creates a flexible pay-per-use Ethernet port rental model for customers. This is especially timely given the Financial Accounting Standards Board proposed [FASB Change 13] that affects operating leases in the balance sheet.
With the Brocade Network Subscription, you pay monthly for the ports you are using. Need more ports, Brocade will install the added gear. Use fewer ports, Brocade will take the equipment back. There is no term endpoint or residual value like tradtional leasing, so when you are done using the equipment, give it back any time. This is ideal for companies that may need to have a lot of Ethernet ports for the next 2-3 years, but then plan to taper down, and don't want to get stuck with a long-term commitment or capital depreciation.
The last speaker was from VMware. IBM is the #1 reseller of VMware, and VMware commands an impressive 81 percent marketshare in the x86 virtualization space. The speaker presented VMware's strategy going forward, which aligns well with IBM's own strategy, to help companies Cloud-enable their existing IT infrastructures, in preparation for eventual moves to Hybrid or Public cloud deployments.
Special thanks to Lief Morin for sponsoring this event, Raquel Hernandez from IBM for coordinating my travel, and Pete, Christina and Kendrell from Key Info Systems for organizing the activities!
During lunch, people were able to take a look at our solutions. Here are Dan Thompson and Brett Cooper striking a pose.
Hyper-Efficient Backup and Recovery
The afternoon was kicked off by Dr. Daniel Sabbah, IBM General Manager of Tivoli software. He started with some shocking statistics: 42 percent of small companies have experienced data loss, 32 percent have lost data forever. IBM has a solution that offers "Unified Recovery Management". This involves a combination of periodic backups, frequent snapshots, and remote mirroring.
IBM Tivoli Storage Manager (TSM) was introduced in 1993, and was the first backup software solution to support backup to disk storage pools. Today, TSM is now also part of Cloud Computing services, including IBM Information Protection Services. IBM announced today a new bundle called IBM Storwize Rapid Application Backup, which combines IBM Storwize V7000 midrange disk system, Tivoli FlashCopy Manager, implementation services, with a full three-year hardware and software warranty. This could be used, for example, to protect a Microsoft Exchange email system with 9000 mailboxes.
IBM also announced that its TS7600 ProtecTIER data deduplication solutions have been enhanced to support many-to-many bi-direction remote mirroring. Last year, University of Pittsburgh Medical Center (UPMC) reported that they were average 24x data deduplication factor in their environment using IBM ProtecTIER.
"You are out of your mind if you think you can live without tape!"
-- Dick Crosby, Director of System Administration, Estes
The new IBM TS1140 enterprise class tape drive process 2.3 TB per hour, and provides a density of 1.2 PB per square foot. The new 3599 tape media can hold 4TB of data uncompressed, which could hold up to 10TB at a 2.5x compression ratio.
The United States Golfers Association [USGA] uses IBM's backup cloud, which manages over 100PB of data from 750 locations across five continents.
Customer Testimonial - Graybar
Randy Miller, Manager of Technical System Administration at Graybar, provided the next client testimonial. Graybar is an employee-owned company focused on supply-chain management, serving as a distributor for electical, lighting, security, power and cooling equipment.
Their problem was that they had 240 different locations, and expecting local staff to handle tape backups was not working out well. They centralized their backups to their main data center. In the event that a system fails in one of their many remote locations, they can rebuild a new machine at their main data center across high-speed LAN, and then ship overnight to the remote location. The result, the remote location has a system up and running by 10:30am, faster than they would have had from local staff trying to figure out how to recover from tape. In effect, Graybar had implemented a "private cloud" for backup in the 1990s, long before the concept was "cool" or "popular".
In 2001, they had an 18TB SAP ERP application data repository. To back this up, they took it down for 1 minute per day, six days a week, and 15 minutes down on Sundays. The result was less than 99.8 percent availability. To fix this, they switched to XIV, and use Snapshots that are non-disruptive and do not impact application performance.
Over 85 percent of the servers at Graybar are virtualized.
Their next challenge is Disaster Recovery. Currently, they have two datacenters, one in St. Louis and the other in Kansas City. However, in the aftermath of Japan's earthquakes, they realize there is a nuclear power plan between their two locations, so a single incident could impact both data centers. They are working with IBM, their trusted advisors, to investigate a three-site solution.
This week, May 15-22, I am in Auckland, New Zealand teaching IBM Storage Top Gun sales class. Next week, I will be in Sydney, Australia.
Continuing my week in Washington DC for the annual [2010 System Storage Technical University], I presented a session on Storage for the Green Data Center, and attended a System x session on Greening the Data Center. Since they were related, I thought I would cover both in this post.
Storage for the Green Data Center
I presented this topic in four general categories:
Drivers and Metrics - I explained the three key drivers for consuming less energy, and the two key metrics: Power Usage Effectiveness (PUE) and Data Center Infrastructure Efficiency (DCiE).
Storage Technologies - I compared the four key storage media types: Solid State Drives (SSD), high-speed (15K RPM) FC and SAS hard disk, slower (7200 RPM) SATA disk, and tape. I had comparison slides that showed how IBM disk was more energy efficient than competition, for example DS8700 consumes less energy than EMC Symmetrix when compared with the exact same number and type of physical drives. Likewise, IBM LTO-5 and TS1130 tape drives consume less energy than comparable HP or Oracle/Sun tape drives.
Integrated Systems - IBM combines multiple storage tiers in a set of integrated systems managed by smart software. For example, the IBM DS8700 offers [Easy Tier] to offer smart data placement and movement across Solid-State drives and spinning disk. I also covered several blended disk-and-tape solutions, such as the Information Archive and SONAS.
Actions and Next Steps - I wrapped up the talk with actions that data center managers can take to help them be more energy efficient, from deploying the IBM Rear Door Heat Exchanger, or improving the management of their data.
Greening of the Data Center
Janet Beaver, IBM Senior Manager of Americas Group facilities for Infrastructure and Facilities, presented on IBM's success in becoming more energy efficient. The price of electricity has gone up 10 percent per year, and in some locations, 30 percent. For every 1 Watt used by IT equipment, there are an additional 27 Watts for power, cooling and other uses to keep the IT equipment comfortable. At IBM, data centers represent only 6 percent of total floor space, but 45 percent of all energy consumption. Janet covered two specific data centers, Boulder and Raleigh.
At Boulder, IBM keeps 48 hours reserve of gasoline (to generate electricity in case of outage from the power company) and 48 hours of chilled water. Many power outages are less than 10 minutes, which can easily be handled by the UPS systems. At least 25 percent of the Computer Room Air Conditioners (CRAC) are also on UPS as well, so that there is some cooling during those minutes, within the ASHRAE guidelines of 72-80 degrees Fahrenheit. Since gasoline gets stale, IBM runs the generators once a month, which serves as a monthly test of the system, and clears out the lines to make room for fresh fuel.
The IBM Boulder data center is the largest in the company: 300,000 square feet (the equivalent of five football fields)! Because of its location in Colorado, IBM enjoys "free cooling" using outside air temperature 63 percent of the year, resulting in a PUE of 1.3 rating. Electricity is only 4.5 US cents per kWh. The center also uses 1 Million KwH per year of wind energy.
The Raleigh data center is only 100,000 Square feet, with a PUE 1.4 rating. The Raleigh area enjoys 44 percent "free cooling" and electricity costs at 5.7 US cents per kWh. The Leadership in Energy and Environmental Design [LEED] has been updated to certify data centers. The IBM Boulder data center has achieved LEED Silver certification, and IBM Raleigh data center has LEED Gold certification.
Free cooling, electricity costs, and disaster susceptibility are just three of the 25 criteria IBM uses to locate its data centers. In addition to the 7 data centers it manages for its own operations, and 5 data centers for web hosting, IBM manages over 400 data centers of other clients.
It seems that Green IT initiatives are more important to the storage-oriented attendees than the x86-oriented folks. I suspect that is because many System x servers are deployed in small and medium businesses that do not have data centers, per se.
The technology industry is full of trade-offs. Take for example solar cells that convert sunlight to electricity. Every hour, more energy hits the Earth in the form of sunlight than the entire planet consumes in an entire year. The general trade-off is between energy conversion efficiency versus abundance of materials:
Get 9-11 percent efficiency using rare materials like indium (In), gallium (Ga) or cadmium (Cd).
Get only 6.7 percent efficiency using abundant materials like copper (Cu), tin (Sn), zinc (Zn), sulfur (S), and selenium (Se)
A second trade-off is exemplified by EMC's recent GeoProtect announcement. This appears similar to the geographic dispersal method introduced by a company called [CleverSafe]. The trade-off is between the amount of space to store one or more copies of data and the protection of data in the event of disaster. Here's an excerpt from fellow blogger Chuck Hollis (EMC) titled ["Cloud Storage Evolves"]:
"Imagine a average-sized Atmos network of 9 nodes, all in different time zones around the world. And imagine that we were using, say, a 6+3 protection scheme.
The implication is clear: any 3 nodes could be completely lost: failed, destroyed, seized by the government, etc.
-- and the information could be completely recovered from the surviving nodes."
For organizations worried about their information falling into the wrong hands (whether criminal or government sponsored!), any subset of the nodes would yield nothing of value -- not only would the information be presumably encrypted, but only a few slices of a far bigger picture would be lost.
Seized by the government?falling into the wrong hands? Is EMC positioning ATMOS as "Storage for Terrorists"? I can certainly appreciate the value of being able to protect 6PB of data with only 9PB of storage capacity, instead of keeping two copies of 6PB each, the trade-off means that you will be accessing the majority of your data across your intranet, which could impact performance. But, if you are in an illicit or illegal business that could have a third of your facilities "seized by the government", then perhaps you shouldn't house your data centers there in the first place. Having two copies of 6PB each, in two "friendly nations", might make more sense.
(In reality, companies often keep way more than just two copies of data. It is not unheard of for companies to keep three to five copies scattered across two or three locations. Facebook keeps SIX copies of photographs you upload to their website.)
ChuckH argues that the governments that seize the three nodes won't have a complete copy of the data. However, merely having pieces of data is enough for governments to capture terrorists. Even if the striping is done at the smallest 512-byte block level, those 512 bytes of data might contain names, phone numbers, email addresses, credit cards or social security numbers. Hackers and computer forensics professionals take advantage of this.
You might ask yourself, "Why not just encrypt the data instead?" That brings me to the third trade-off, protection versus application performance. Over the past 30 years, companies had a choice, they could encrypt and decrypt the data as needed, using server CPU cycles, but this would slow down application processing. Every time you wanted to read or update a database record, more cycles would be consumed. This forced companies to be very selective on what data they encrypted, which columns or fields within a database, which email attachments, and other documents or spreadsheets.
An initial attempt to address this was to introduce an outboard appliance between the server and the storage device. For example, the server would write to the appliance with data in the clear, the appliance would encrypt the data, and pass it along to the tape drive. When retrieving data, the appliance would read the encrypted data from tape, decrypt it, and pass the data in the clear back to the server. However, this had the unintended consequences of using 2x to 3x more tape cartridges. Why? Because the encrypted data does not compress well, so tape drives with built-in compression capabilities would not be able to shrink down the data onto fewer tapes.
(I covered the importance of compressing data before encryption in my previous blog post
[Sock Sock Shoe Shoe].)
Like the trade-off between energy efficiency and abundant materials, IBM eliminated the trade-off by offering compression and encryption on the tape drive itself. This is standard 256-bit AES encryption implemented on a chip, able to process the data as it arrives at near line speed. So now, instead of having to choose between protecting your data or running your applications with acceptable performance, you can now do both, encrypt all of your data without having to be selective. This approach has been extended over to disk drives, so that disk systems like the IBM System Storage DS8000 and DS5000 can support full-disk-encryption [FDE] drives.
Am I dreaming? On his Storagezilla blog, fellow blogger Mark Twomey (EMC) brags about EMC's standard benchmark results, in his post titled [Love Life. Love CIFS.]. Here is my take:
A Full 180 degree reversal
For the past several years, EMC bloggers have argued, both in comments on this blog, and on their own blogs, that standard benchmarks are useless and should not be used to influence purchase decisions. While we all agree that "your mileage may vary", I find standard benchmarks are useful as part of an overall approach in comparing and selecting which vendors to work with, and which architectures or solution approaches to adopt, and which products or services to deploy. I am glad to see that EMC has finally joined the rest of the planet on this. I find it funny this reversal sounds a lot like their reversal from "Tape is Dead" to "What? We never said tape was dead!"
Impressive CIFS Results
The Standard Performance Evaluation Corporation (SPEC) has developed a series of NFS benchmarks, the latest, [SPECsfs2008] added support for CIFS. So, on the CIFS side, EMC's benchmarks compare favorably against previous CIFS tests from other vendors.
On the NFS side, however, EMC is still behind Avere, BlueArc, Exanet, and IBM/NetApp. For example, EMC's combination of Celerra gateways in front of V-Max disk systems resulted in 110,621 OPS with overall response time of 2.32 milliseconds. By comparison, the IBM N series N7900 (tested by NetApp under their own brand, FAS6080) was able to do 120,011 OPS with 1.95 msec response time.
Even though Sun invented the NFS protocol in the early 1980s, they take an EMC-like approach against standard benchmarks to measure it. Last year, fellow blogger Bryan Cantrill (Sun) gives his [Eulogy for a Benchmark]. I was going to make points about this, but fellow blogger Mike Eisler (NetApp) [already took care of it]. We can all learn from this. Companies that don't believe in standard benchmarks can either reverse course (as EMC has done), or continue their downhill decline until they are acquired by someone else.
(My condolences to those at Sun getting laid off. Those of you who hire on with IBM can get re-united with your former StorageTek buddies! Back then, StorageTek people left Sun in droves, knowing that Sun didn't understand the mainframe tape marketplace that StorageTek focused on. Likewise, many question how well Oracle will understand Sun's hardware business in servers and storage.)
What's in a Protocol?
Both CIFS and NFS have been around for decades, and comparisons can sometimes sound like religious debates. Traditionally, CIFS was used to share files between Windows systems, and NFS for Linux and UNIX platforms. However, Windows can also handle NFS, while Linux and UNIX systems can use CIFS. If you are using a recent level of VMware, you can use either NFS or CIFS as an alternative to Fibre Channel SAN to store your external disk VMDK files.
The Bigger Picture
There is a significant shift going on from traditional database repositories to unstructured file content. Today, as much as [80 percent of data is unstructured]. Shipments this year are expected to grow 60 percent for file-based storage, and only 15 percent for block-based storage. With the focus on private and public clouds, NAS solutions will be the battleground for 2010.
So, I am glad to see EMC starting to cite standard benchmarks. Hopefully, SPC-1 and SPC-2 benchmarks are forthcoming?
IBM makes another breakthrough today with an announcement about tape data density. Unlike hard disk drive technologies that are hitting physical limits, IBM is proving that tape technology still has plenty of life in its future.
When I first started working for IBM in Tucson, back in 1986, a 3420 tape reel held only 180MB of data, and a 3480 tape cartridge improved this to 200MB of data. Today's enterprise tapes, like 3592 cartridges for the TS1130 drives, or LTO4 cartridges for the IBM TS1040 drives, are half-inch wide, half-mile long, and can store 1 TB or more of data per cartridge, depending on how well the data can compress. To increase cartridge capacity, designers can make changes in three dimensions:
Wider tape: The film industry tried this, going from 35mm to 70mm film, only to find that most cinemas did not want to upgrade their equipment. Keeping the media dimensions to half inch wide allows much of the engineering hardware to continue unchanged.
Longer tape: The problem with longer tape is that either the reel inside gets fatter, or you need to develop flatter media to fit within the existing cartridge dimensions. Wider reels means a bigger tape cartridge external dimensions, forcing changes to shelving units, cartridge trays, and carrying units. The media just can't get any flatter without risking getting more brittle.
Denser bit recording: once a convenient width and length were established, improving bit density turned out to be the best way to increase cartridge capacity.
Working with FujiFilm Corporation of Japan, my colleagues at IBM Research facility in Zurich were able to demonstrate an incredible 29.5 Gigabits per square inch, nearly 40 times more dense than today's commercial tape technology. In the near future, we will be able to hold a 35TB tape cartridge in our hand. There was actually a lot to make this happen, improved giant magentoresistive read/write heads, better servo patterns to stay on track, thinner tracks less than a micron thick, and better signal-to-noise processing to accomplish this. To learn more, you can read the [Press Release] or watch this quick [4-minute YouTube video].
Well, it's Tuesday, and that means IBM announcements! Today is bigger, as there are a lot of Dynamic Infrastructure announcements throughout the company with a common theme, cloud computing and smart business systems that support the new way of doing things. Today, IBM announced its new "IBM Smart Archive" strategy that integrates software, storage, servers and services into solutions that help meet the challenges of today and tomorrow. IBM has been spending the past few years working across its various divisions and acquisitions to ensure that our clients have complete end-to-end solutions.
IBM is introducing new "Smart Business Systems" that can be used on-premises for private-cloud configurations, as well as by cloud-computing companies to offer IT as a service.
IBM [Information Archive] is the first to be unveiled, a disk-only or blended disk-and-tape Information Infrastructure solution that offers a "unified storage" approach with amazing flexibility for dealing with various archive requirements:
For those with applications using the IBM Tivoli Storage Manager (TSM) or IBM System Storage Archive Manager (SSAM) API of the IBM System Storage DR550 data retention solution, the Information Archive will provide a direct migration, supporting this API for existing applications.
For those with IBM N series using SnapLock or the File System Gateway of the DR550, the Information Archive will support various NAS protocols, deployed in stages, including NFS, CIFS, HTTP and FTP access, with Non-Erasable, Non-Rewriteable (NENR) enforcement that are compatible with current IBM N series SnapLock usage.
For those using NAS devices with PACS applications to store X-rays and other medical images, the Information Archive will provide similar NAS protocol interfaces. Information Archive will support both read-only data such as X-rays, as well as read/write data such as Electronic Medical Records.
Information Archive is not just for compliance data that was previously sent to WORM optical media. Instead, it can handle all kinds of data, rewriteable data, read-only data, and data that needs to be locked down for tamper protection. It can handle structured databases, emails, videos and unstructured files, as well as objects stored through the SSAM API.
The Information Archive has all the server, storage and software integrated together into a single machine type/model number. It is based on IBM's General Parallel File System (GPFS) to provide incredible scalability, the same clustered file system used by many of the top 500 supercomputers. Initially, Information Archive will support up to 304TB raw capacity of disk and Petabytes of tape. You can read the [Spec Sheet] for other technical details.
For those who prefer a more "customized" approach, similar to IBM Scale-Out File Services (SoFS), IBM has [Smart Business Storage Cloud]. IBM Global Services can customize a solution that is best for you, using many of the same technologies. In fact, IBM Global Services announced a variety of new cloud-computing services to help enterprises determine the best approach.
In a related announcement, IBM announced [LotusLive iNotes], which you can think of as a "business-ready" version of Google's GoogleApps, Gmail and GoogleCalendar. IBM is focused on security and reliability but leaves out the advertising and data mining that people have been forced to tolerate from consumer-oriented Web 2.0-based solutions. IBM's clients that are already familiar with on-premises version of Lotus Notes will have no trouble using LotusLive iNotes.
There was actually a lot more announced today, which I will try to get to in later posts.
Over on his Backup Blog, fellow blogger Scott Waterhouse from EMC has a post titled
[Backup Sucks: Reason #38]. Here is an excerpt:
Unfortunately, we have not been able to successfully leverage economies of scale in the world of backup and recovery. If it costs you $5 to backup a given amount of data, it probably costs you $50 to back up 10 times that amount of data, and $500 to back up 100 times that amount of data.
If anybody can figure out how to get costs down to $40 for 10 times the amount of data, and $300 for 100 times the amount of data, they will have an irrefutable advantage over anybody that has not been able to leverage economies of scale.
I suspect that where Scott mentions we in the above excerpt, he is referring to EMC in general, with products like
Legato. Fortunately, IBM has scalable backup solutions, using either a hardware approach, or one purely with software.
The hardware approach involves using deduplication hardware technology as the storage pool for IBM Tivoli Storage Manager (TSM). Using this approach, IBM Tivoli Storage Manager would receive data from dozens, hundreds or even thousands
of client nodes, and the backup copies would be sent to an IBM TS7650 ProtecTIER data deduplication appliance, IBM TS7650G gateway, or IBM N series with A-SIS. In most cases, companies have standardized on the operating systems and applications used on these nodes, and multiple copies of data reside across employee laptops. As a result, as you have more nodes backing up, you are able to achieve benefits of scale.
Perhaps your budget isn't big enough to handle new hardware purchases at this time, in this economy. Have no fear,
IBM also offers deduplication built right into the IBM Tivoli Storage Manager v6 software itself. You can use sequential access disk storage pool for this. TSM scans and identifies duplicate chunks of data in the backup copies, and also archive and HSM data, and reclaims the space when found.
If your company is using a backup software product that doesn't scale well, perhaps now is a good time to switch over to IBM Tivoli Storage Manager. TSM is perhaps the most scalable backup software product in the marketplace, giving IBM an "irrefutable advantage" over the competition.
Continuing my week in Chicago, for the IBM Storage Symposium 2008, I attended two presentations on XIV.
XIV Storage - Best Practices
Izhar Sharon, IBM Technical Sales Specialist for XIV, presented best practices using XIV in various environments.He started out explaining the innovative XIV architecture: a SATA-based disk system from IBM can outperformFC-based disk systems from other vendors using massive parallelism. He used a sports analogy:
"The men's world record for running 800 meters was set in 1997 by Wilson Kipketer of Denmark in a time of 1:41.11.
However, if you have eight men running, 100 meters each, they will all cross the finish line in about 10 seconds."
Since XIV is already self-tuning, what kind of best practices are left to present? Izhar presented best practicesfor software, hosts, switches and storage virtualization products that attach to the XIV. Here's some quickpoints:
Use as many paths as possible.
IBM does not require you to purchase and install multipathing software as other competitors might. Instead, theXIV relies on multipathing capabilities inherent to each operating system.For multipathing preference, choose Round-Robin, which is now available onAIX and VMware vSphere 4.0, for example. Otherwise, fixed-path is preferred over most-recently-used (MRU).
Encourage parallel I/O requests.
XIV architecture does not subscribe to the outdated notion of a "global cache". Instead, the cache is distributed across the modules, to reduce performance bottlenecks. Each HBA on the XIV can handle about 1400requests. If you have fewer than 1400 hosts attached to the XIV, you can further increase parallel I/O requests by specifying a large queue depth in the host bus adapter (HBA).An HBA queue depth of 64 is a good start. Additional settings mightbe required in the BIOS, operating system or application for multiple threads and processes.
For sequential workloads, select host stripe size less than 1MB. For random, select host stripe size larger than 1MB. Set rr_min_io between ten(10) and the queue depth(typically 64), setting it to half of the queue depth is a good starting point.
If you have long-running batch jobs, consider breaking them up into smaller steps and run in parallel.
Define fewer, larger LUNs
Generally, you no longer need to define many small LUNs, a practice that was often required on traditionaldisk systems. This means that you can now define just 1 or 2 LUNs per application, and greatly simplifymanagement. If your application must have multiple LUNs in order to do multiple threads or concurrent I/O requests, then, by all means, define multiple LUNs.
Modern Data Base Management Systems (DBMS) like DB2 and Oracle already parallelize their I/O requests, sothere is no need for host-based striping across many logical volumes. XIV already stripes the data for you.If you use Oracle Automated Storage Management (ASM), use 8MB to 16MB extent sizes for optimal performance.
For those virtualizing XIV with SAN Volume Controller (SVC), define manage disks as 1632GB LUNs, in multiple of six LUNs per managed disk group (MDG), to balance across the six interface modules. Define SVC extent size to 1GB.
XIV is ideal for VMware. Create big LUNs for your VMFS that you can access via FCP or iSCSI.
Organize data to simplify Snapshots.
You no longer need to separate logs from databases for performance reasons. However, for some backup productslike IBM Tivoli Storage Manager (TSM) for Advanced Copy Services (ACS), you might want to keep them separatefor snapshot reasons. Gernally, putting all data for an application on one big LUNgreatly simplifies administration and snapshot processing, without losing performance.If you define multiple LUNs for an application, simply put them into the same "consistencygroup" so that they are all snapshot together.
OS boot image disks can be snapshot before applying any patches, updates or application software, so that ifthere are any problems, you can reboot to the previous image.
Employ sizing tools to plan for capacity and performance.
The SAP Quicksizer tool can be used for new SAP deployments, employing either the user-based orthroughput-based sizing model approach. The result is in mythical unit called "SAPS", which represents0.4 IOPS for ERP/OLTP workloads, and 0.6 IOPS for BI/BW and OLAP workloads.
If you already have SAP or other applications running, use actual I/O measurements. IBM Business Partners and field technical sales specialists have an updated version of Disk Magic that can help size XIV configurations fromPERFMON and iostat figures.
Lee La Frese, IBM STSM for Enteprise Storage Performance Engineering, presented internal lab test results forthe XIV under various workloads, based on the latest hardware/software levels [announced two weeks ago]. Three workloadswere tested:
Web 2.0 (80/20/40) - 80 percent READ, 20 percent WRITE, 40 percent cache hits for READ.YouTube, FlickR, and the growing list at [GoWeb20] are applications with heavy read activity, but because of[long-tail effects], may not be as cache friendly.
Social Networking (50/50/50) - 50 percent READ, 50 percent WRITE, 50 percent cache hits for READ.Lotus Connections, Microsoft Sharepoint, and many other [social networking] usage are more write intensive.
Database (70/30/50) - 70 percent READ, 30 percent WRITE, 50 percent cache hits for READ.The traditional workload characteristics for most business applications, especially databases like DB2 andOracle on Linux, UNIX and Windows servers.
The results were quite impressive. There was more than enough performance for tier 2 application workloads,and most tier 1 applications. The performance was nearly linear from the smallest 6-module to the largest 15-module configuration. Some key points:
A full 15-module XIV overwhelms a single SVC 8F4 node-pair. For a full XIV, consider 4 to 8 nodes 8F4 models, or 2 to 4 nodes of an 8G4. For read-intensive cache-friendly workloads, an SVC in front of XIV was able to deliver over 300,000 IOPS.
A single node TS7650G ProtecTIER can handle 6 to 9 XIV modules. Two nodes of TS7650G were needed to drivea full 15-module XIV. A single node TS7650 in front of XIV was able to ingest 680 MB/sec on the seventh day with17 percent per-day change rate test workload using 64 virtual drives. Reading the data back got over 950 MB/sec.
For SAP environments where response time 20-30 msec are acceptable, the 15-module XIV delivered over 60,000 IOPS. Reducing this down to 25,000-30,000 cut the msec response time to a faster 10-15 msec.
These were all done as internal lab tests. Your mileage may vary.
Not surprisingly, XIV was quite the popular topic here this week at the Storage Symposium. There were many moresessions, but these were the only two that I attended.
Continuing my week in Chicago for the IBM Storage and Storage Networking Symposium and System x and BladeCenter Technical Conference, I presented a variety of topics.
Hybrid Storage for a Green Data Center
The cost of power and cooling has risen to be a #1 concern among data centers. I presented the following hybrid storage solutions that combine disk with tape. These provide the best of both worlds, the high performance access time of disk with the lower costs and reduced energy consumption of tape.
IBM [System Storage DR550] - IBM's Non-erasable, Non-rewriteable (NENR) storage for archive and compliance data retention
IBM Grid Medical Archive Solution [GMAS] - IBM's multi-site grid storage for PACS applications and electronic medical records[EMR]
IBM Scale-out File Services [SoFS] - IBM's scalable NAS solution that combines a global name space with a clustered GPFS file system, serving as the ideal basis for IBM's own[Cloud Computing and Storage] offerings
Not only do these help reduce energy costs, they provide an overall lower total cost of ownership (TCO) thantraditional WORM optical or disk-only storage configurations.
The Convergence of Networks - Understanding SAN, NAS and iSCSI in the Data Center Network
This turned out to be my most popular session. Many companies are at a crossroads in choosing data and storage networking solutions in light of recent announcements from IBM and others. In the span of 75 minutes, I covered:
Block storage concepts, storage virtualization and RAID levels
File system concepts, how file systems map files to block storage
Network Attach Storage, the history of the NFS and CIFS protocols, Pros and Cons of using NAS
Storage Area Networks, the history of SAN protocols including ESCON, FICON and FCP, Pros and Cons of using SAN
IP SAN technologies, iSCSI and Fibre Channel over Ethernet (FCoE), Pros and Cons of using this approach
Network Convergence with Infiniband and Fibre Channel over Convergence Enhanced Ethernet (FCoCEE), why Infiniband was not adopted historically in the marketplace as a storage protocol, and the features and enhancements of Convergence Enhanced Ethernet (CEE) needed to merge NAS, SAN and iSCSI traffic onto a single converged data center network [DCN]
Yes, it was a lot of information to cover, but I managed to get it done on time.
IBM Tivoli Storage Productivity Center version 4.1 Overview and Update
In conferences like these, there are two types of product-level presentations. An "Overview" explains howproducts work today to those who are not familiar with it. An "Update" explains what's new in this version of the product for those who are already familiar with previous releases. I decided to combine these into one sessionfor IBM's new version of [Tivoli Storage Productivity Center].I was one of the original lead architects of this product many years ago, and was able to share many personalexperiences about its evolution in development and in the field at client facilities.Analysts have repeatedly rated IBM Productivity Center as one of the top Storage Resource Management (SRM) tools available in the marketplace.
Information Lifecycle Management (ILM) Overview
Can you believe I have been doing ILM since 1986? I was the lead architect for DFSMS which provides ILM support for z/OS mainframes. In 2003-2005, I spent 18 months in the field performingILM assessments for clients, and now there are dozens of IBM practitioners in Global Technology Services andSTG Lab Services that do this full time. This is a topic I cover frequently at the IBM Executive Briefing Center[EBC], because it addressesseveral top business challenges:
Reducing costs and simplifying management
Improving efficiency of personnel and application workloads
Managing risks and regulatory compliance
IBM has a solution based on five "entry points". The advantage of this approach is that it allows our consultants to craft the right solution to meet the specific requirements of each client situation. These entry points are:
Tiered Information Infrastructure - we don't limit ourselves to just "Tiered Storage" as storage is only part of a complete[information infrastructure] of servers,networks and storage
Storage Optimization and Virtualization - including virtual disk, virtual tape and virtual file solutions
Process Enhancement and Automation - an important part of ILM are the policies and procedures, such as IT Infrastructure Library [ITIL] best practices
Archive and Retention - space management and data retention solutions for email, database and file systems
I did not get as many attendees as I had hoped for this last one, as I was competing head-to-head in the same time slot as Lee La Frese covering IBM's DS8000 performance with Solid State Disk (SSD) drives, John Sing covering Cloud Computing and Storage with SoFS, and Eric Kern covering IBM Cloudburst.
I am glad that I was able to make all of my presentations at the beginning of the week, so that I can then sit back and enjoy the rest of the sessions as a pure attendee.
Well, it's Tuesday, and you know what that means? IBM announcements!
Today we had several for the IBM System Storage product line. Here are some of them:
DS8000 gets thinner, leaner and faster
The 4.3 level of microcode for the IBM System Storage DS8000 series disk systems [announced enhancements] for both fixed block architecture (FBA) LUNs and count key data (CKD) volumes.
For FBA LUNs that attach to Linux, UNIX and Windows distributed systems, IBM announced DS8000 Thin Provisioning native support. Of course, many people already had this by putting IBM System Storage SAN Volume Controller (SVC) in front, but now DS8000 clients out there without SVC can also achieve benefits ofthin provisioning. This support also improves quick initialization a whopping 2.6 times faster.
For CKD volumes attached to z/OS on System z mainframes, IBM announced zHPF multitrack support for z/OS 1.9 and above. zHPF provide high performance FICON performance, and can now handle multitrack I/O transfers foreven better performance for zFS, HFS, PDSE, and extended striped data sets.
XIV gets better connected
A lot of XIV[announced enhancements] and preview announcements centered around better connectivity. Here's a run down:
Better host attachment connectivity by beefing up the interface modules that hold the FCP and iSCSI interface cards. XIV disk arrays have 3 to 6 of these in different configurations, and since they manage both their own disks,as well as receive host I/O requests for other disks, are basically doing double-duty.These interface modules can now be ordered as [Dual-CPU] modules.
Better infrastructure management by connecting XIV with the industry standard SMI-S interface to IBM Tivoli Storage Productivity Center. Now, XIV can be part of the single pane of glass console that manages all of your other disk arrays, tape libraries and SAN fabrics.
Better copy services for backups by connecting XIV with IBM Tivoli Storage Manager Advanced Copy Services. TSM for Advanced Copy Services is application aware and can coordinate XIV Snapshots similar to its current support for SVC and DS8000 FlashCopy capabilities.
Better connectivity to security systems by supporting LDAP credentials. Before, you had individual userid and passwords for each XIV, and these were probably different than all the other userid/password combinations you have for every other box on your data center floor. IBM is working on getting all products to support theLightweight Directory Access Protocol, or [LDAP] so that we can reach the nirvana of "single sign-on",one userid/password per administrator for all IT devices in the company.
Better support with flexible warranty periods and non-disruptive code load options.
Better remote copy support by connecting to sites far, far away. IBM previewed that it will provideasynchronous disk mirroring from one XIV to another XIV natively. Before this, XIV's synchronous mirroring was limited to 300km distances. Many of our clients do long distance global mirroring of their XIV today behind an SVC, but again, for those out there that don't yet have an SVC, this can be a reasonable alternative.
TS7650 ProtecTIER data deduplication appliance now offers "no dedupe" option
In what some might consider a surprising move, IBM announced a "no dedupe" licensing option on their premiere deduplication solution, which somewhat reminds me of IBM's NOCOPY option on DS8000 FlashCopy. At first I thought "Are you kidding me?!?!" However, this new license option allows the TS7650 appliance to compete with other virtual tape libraries (VTL) that do not offer deduplication capability on an even playing field. It also allows TS7650 to be used for data that doesn'tdedupe very well, such as seismic recordings, satellite images, or what have you. There are also clients who do not yet feel comfortable to dedupe their financial records for compliance reasons.This option now allows IBM to withdraw from marketing the TS7530 non-dedupe library. Having one technology thatdoes both dedupe and no-dedupe is better than offering two separate libraries based on different technologies.
The ProtecTIER series also announced [IP remote distance replication]. This can be used to replicate virtualtape cartridges in one ProtecTIER over to another ProtecTIER at a remote location. You can decide to replicateall or just a subset of your virtual tapes, and this feature can be used to migrate, merge or split ProtecTIERconfigurations as your needs grow. Before this support, our TS7650G clients replicated the disk repositoryusing native disk array replication technology, such as Global Mirror on the DS8000, but that meant that all data was replicated over to the secondary site. Now, with this new IP replication feature, you can be selective, and replicate only those virtual tapes that are mission critical.
The appliance now supports up to 36TB of disk capacity, and the new "IBM i" operating system on System i servers,formerly known as i5/OS.
GPFS does Windows
IBM's General Parallel File System (GPFS) has the lion's marketshare of file systems used in the [Top 500 Supercomputers]. For a while, it was limited to just Linux and AIX operating system support, but version 3.3 [extends this to Windows 2008 on 64-bit architectures]. GPFS isthe file system used in IBM's Scale-Out File Services, the underlying technology of IBM's Cloud Computing and Storage offerings.
Now that the frozen economy is starting to thaw, I have been traveling like crazy this month. So far, I have been to Rochester, MN, Los Angeles and San Diego, CA, and now currently in Austin, TX. On the plus side, I was able to enjoy the [Fourth of July] holiday weekend on the beaches of San Diego.
(If you have not been to California beaches lately, here's a quick [video] reminder)
So the big news this week is that the auction over Data Domain is over, and EMC's bid finally won over NetApp. Both NetApp and EMC have data deduplication capabilities in their existing product lines, but neither could compete against IBM's TS7650G ProtecTIER Data Deduplication gateway and TS7650 ProtecTIER appliances, and so were hell-bent to buy Data Domain for large amounts. The final price agreed upon was over two billion US dollars for Data Domain.
For the most part, Data Domain's products are targeted towards small and medium sized businesses, whereas IBM's TS7650 and TS7650G products targets medium and larger sized enterprises.So now that EMC has a viable data deduplication solution, it looks like it will be yet another IBM-vs-EMC debate going forward.
Continuing this week's theme of doing important things without leaving town, I present our results foran exciting project I started earlier this year.
For seven weeks, my coworker Mark Haye and I voluntarily led a class of students here in Tucson, Arizona in an after-school pilot project to teach the ["C" programming language] using [LEGO® Mindstorms® NXT robots]. The ten students, boys and girls ages 9 to 14 years old, were already part of the FIRST [For Inspiration and Recognition of Science and Technology] program, and participated in FIRST Lego League[FLL] robot competitions.Since the students were already familiar building robots, and programming them with a simple graphical system of connecting blocks that perform actions. However, to compete in the next level of robot competitions, FIRST Tech Challenge [FTC],we need to leave this simple graphical programming behind, and upgrade to more precise "C" programming.
Mark is a software engineer for IBM Tivoli Storage Manager and has participated in FLL competitions over the past nine years. This week, he celebrates his 25th anniversary at IBM, and I celebrate my 23rd. The teacher, Ms. Ackerman, and the students referred to us as "Coach Mark" and "Coach Tony".
This was the first time I had worked with LEGO NXT robots. For those not familiar with these robots, you can purchase a kit at your localtoy store. In addition to regular LEGO bricks, beams, and plates, there are motors, wheels, and sensors. A programmable NXT brick has three outputs (marked A,B, and C) to control three motors, and four inputs (marked 1,2,3,4) to receive values from sensors. Programs are written and compiled on laptops and then downloaded to the NXT programmable brick through an USB cable, or wirelessly via Bluetooth.
In the picture shown, an image of the Mars planetary surface is divided into a grid with thick black lines.A light sensor between the front two wheels of the robot is over the black line.
We used the [RobotC programming firmware] and integrated development environment (IDE) from [Carnegie Mellon University].The idea of this pilot was to see how well the students could learn "C". With only a few hours after class on each Wednesday, could we teach young students "C" programming in just seven weeks?
My contribution? I have taught both high school and college classes, and spent over 15 years programming for IBM, so Mark asked me to help.We started with a basic lesson plan:
A brief history of the "C" language
Understanding statements and syntax
Setting motor speed and direction
Compiling and downloading your first program
Understanding the "while" loop
Retrieving input sensor values
Understanding the "if-then-else" statement
Defining variables with different data types
Manipulating string variables
Writing a program for the robot to track along a black line on a white background.
Understanding local versus global scope variables
Writing a program for a robot to count black lines as it crosses them.
Perform left turns, right turns, and to cross a specific number of lines on a grid pattern to move the robot to a specific location.
Weeks 6 and 7
Mission Impossible: come up with a challenge to make the robot do something that would be difficult to accomplish using the previous NXT visual programming language.
At the completion of these seven weeks, I sat down to interview "Coach Mark"on his thoughts on this pilot project.
This is a practical programming skill. The "C" language is used throughout the world to program everything from embedded systems to operating systems, and even storage software. This would allow the robots to handle more precise movements, more accurate turns, and more complicated missions.
Can kids learn "C" in only seven weeks?
Part of the pilot project was to see how well the students could understand the material. They were already familiar with building the robots, and understood the basics of programming sensors and motors, so we were hoping this was a good foundation to work from. Some kids managed very well, others struggled.
Did everything go according to plan?
The first two weeks went well, turning on motors and having robots move forward and backward were easy enough. We seemed to lose a few students on week 3, and things got worse from there. However, several of the students truly surprised us and managed to implement very complicated missions. We were quite pleased with the results.
What kind of problems did the kids encounter?
Touch sensor required loops waiting for pressing. Motors did not necessarily turn as expected until more advanced methods were used. Making 90 degree left and right turns accurately was more difficult than expected.
Any funny surprises?
Yes, we had a Challenge Map representing the Mars planetary surface from a previous FLL competition that was dark red and divided into squares with thick black lines. An active light sensor returns a value of "0" (complete darkness) to "100" (bright white).However, the Mars surface had craters that were dark enough to be misinterpreted as a black line causing some unusual results. This required some enhanced programming techniques to resolve.
Did robots help or hurt the teaching process?
I think they helped. Rather than writing programs that just display "Hello World!" on a computer screen, the students can actually see robots move, and either do what they expect, or not!
And when the robots didn't do what they were expected to?
The students got into "debug" mode. They were already used to doing this from previous FLL competitions, but with RobotC, you can leave the USB cable connected (or use wireless Bluetooth) and actually gather debugging information while the robot is running, to see the value of sensors and other variables and help determine why things are not working properly.
Any applicability to the real world of storage?
We have robots in the IBM System Storage TS3500 tape library. These robots scan bar code labels, pull tapes out of shelves and mount them into drives.The programming skills are the same needed for storage software, suchas IBM Tivoli Storage Manager or IBM Tivoli Storage Productivity Center.
The world is becoming smarter, instrumented with sensors, interconnected over a common network, and intelligent enough to react and respond correctly. The lessons of reading sensor values and moving motors can be considered the first step in solutions that help to make a smarter planet.
This week I am in Costa Rica to celebrate[Earth Day] and promote IBM's [Smarter Planet strategy] to help solve the world's energy and environmental problems. This is thethird in the series. The first two posts were:
Here in Costa Rica, they separate their recyclables, and encourage even the hotel guests from other countries to do the same. See my photo on the left for an example.
This is more than most in the United States will do. We're lucky to get North Americans to just separate all recyclables in one bin separate from all trash in a second bin.
Leaving Arenal, I went to Escazu, a suburb of San Jose, the capital of this country. I met with Patrick, one of the owners of [Exclusive Excursions Travel] that helped me organize the eco-tourism portion of this trip to Costa Rica.
Most people are familiar with the [star rating system] that rank most hotels from one star (budget class/economy) to five stars (deluxe/luxury). The nicest hotel I've been to was the [Burj Al Arab] in Dubai, which claims a seven star rating. For eco-tourism, there is a similar "Green Leaf" rating system. According to Patrick,the Instituto Costarricense de Turismo [ICT] (tourism board of Costa Rica) rates hotels from one leaf (adopting some measures, like separating recyclables shown above) to five leaves (entirely carbon neutral).This Green Leaf system seems more important to European and Canadian tourists, but those from United States may not even be aware of it.
The food at these hotels vary. The typical dish here for breakfast, lunch and dinner is the Casado, consisting of mostly rice and beans. I have found thatCosta Rica has come up with as many creative ways to combine rice and beans in various proportions as Starbucks® serve various combinations of coffee and milk.The locals might be accustomed to a steady diet of rice and beans for every meal of every day, but those of us from North America aren't! Not counting tourist flatulence, Costa Rica has[pledged to be carbon neutral by 2021], the country's 200th birthday.
Sadly, most folks in the United States don't categorize their hotels with a Green Leaf rating system, nor do they even bother to categorize their recyclables. I spent 18 months in the field doing Information Lifecycle Management (ILM) assessments for clients, and most didn't categorize their data either.So, the next time you have some combination of coffee and milk, whether its a Latte, Misto, Espresso, or Macchiato, remember that the coffee came from acountry trying to be more environmentally responsible, grown by a farmerwho eats a simple diet of rice and beans, and has no problem separating different categories of recyclables. Perhaps you will remember to separate your data, and store it on an information infrastructure based on an environmentally-responsible combination of SSD, FC, SATA and tape, to reduce your costs and minimize your carbon footprint.
With mixed emotions, Jon Peake announced he will retire from IBM next week. Jon is known as thefather of IBM Virtual Tape Server (VTS), the industry's first virtual tape system, announced in 1996and generally available in 1997.One of my 19 patents was for the VTS pre-migration capability, and as lead architect for DFSMS, I worked closely with Jon and his tape systems team to ensure its success.
From left to right:
Chris Telford, IBM Development manager for Enterprise Tape Integration
Jon Peake, IBM Distinguished Engineer and Master Inventor
Annette Estelle, Jon's global admin assistant
At his retirement celebration, Jon was awarded the coveted "Project Bulldog" jacket, which has an interesting history.
In response to IBM's 1996 VTS announcement, the top StorageTek (STK) tape sales teams and most of the dedicated tape technicians were invited to a global assembly at a fancy resort in Winter Park, CO (about 90 miles west of STK's Louisville headquarters) in early 1997. The gathering was named Project Bulldog, after Ron Korngiebel, STK's director of competitive marketing, who I am told had voice and facial resemblance to justify the project moniker. Ron had recruited Fred Moore, Steve Blenderman, and other prized engineers as speakers. I have seen both Fred and Steve speak at various conferences such as SHARE and GUIDE, and agree they are high quality speakers.
The goal was to have STK's brightest in Louisville go down in the trenches, work the field guys into a frenzy, defend STK Tape at any cost, and send IBM packing. At the end of the two day fest, many participants received the coveted Project Bulldog jacket.
Former STKers who now work at IBM can remember this meeting involved:
Bashing of the [IBM Seascape] architecture approach. The use of commodity servers and componentsto build storage systems continues today in the IBM System Storage DS8000, SAN Volume Controller,XIV, and TS7650 Deduplication solutions.
Explanations how and why IBM's VTS would never work, and how only STK virtual tape would make it in the market. Today, IBM is the leader in storage virtualization, both for disk and tape.
Mock interview videos with claims that IBM could never figure out how to attach IBM drives to the STK Silo. I was a big proponent of this, having visited customers who specifically asked for IBM to sell its better, faster IBM drives into their existing STK silos. At first, upper management was hesitant to do this, but the IBMengineers worked out what changes were needed, and today many STK tape automation libraries run with IBM tape drives.
While some analysts frowned on Sun's [2005 acquisition of StorageTek], IBM was delighted, given Sun's previous track record in storagecompany acquisitions. I joke that we are still picking up confetti in the hallways of IBM's Tucsonlab. I was in New York city when I heard Sun's announcement, and it didn't take long for STKemployees offering me their resumes.Since then, many STK engineers, technicians and sales team have left Sun, many coming over to IBM.Back then, there were many intelligent and talented people working for StorageTek, and IBM is gladto have hired them.
With the resurgence of interest in tape systems, from dealing with new legislation for long term retention of electronic data to a focus on energy efficiency, Jon leaves much like a champion retiring at the top of his game.
Jon, I am going to miss you! Enjoy your retirement!